George16

I had been using mine with my X5 for a year now without any problems at all.

6.63 lbs. Sig MPX PCC

For me, it wasn’t. I don’t have any problems with CCI, Winchester and federal primers plus factory ammo with my setup of factory firing pin and spring with the CGW 11.5# hammer spring. I used this setup when my reduced power firing pin spring broke during a match.

I can’t remember it but it’s on CZ USA website.

The old style mag release on the older TSO will do that. I alleviated that by grinding down, drilling and tapping the mag release and installed a shadow 2 pad. It also helped me after I removed the slide stop and installed just the side stop pin and taped the hole where that slide release once was.

Same here. Ordered 4K of the 124 Gr JHP. Great prices.

What ammo are you using and at what distance are you shooting at? Shadow 2s were sighted in at the factory using 124 Gr FMJ at 25 yards. Even if you were shooting a different type of ammo, it shouldn’t be shooting that far off unless there is something wrong (loose setscrew) on the rear sight itself. I have seen and experienced a loose set screw on mine and didn’t realize until I let a friend shot it. First thing he asked me after shooting it was, “did you check if the set screws are tight..” of course it wasn’t.

TTI has 25% off of parts using TTIParts25 code. Bought some mag extensions, magwell and MPX stock adaptor yesterday.

Thanks. Just ordered some mag extensions for my MPX.

Very nice setup Mo! Which grip are you using? Is that aluminum shroud threaded and then pinned and welded to the barrel?

Damn! I was just talking to him via pm last week. RIP Mike.

It’s free shipping from RMR regardless of quantity.

I have the Luth MBA 3 linked in the previous post on my 308 and it helps a lot since I have a big scope on my rifle. It gives me a higher cheek weld when shooting with it.

7.3 Gr @ 1.149-1.151” OAL for my Czechmate. PF is around 169 PF for 115 Gr PD JHP. 6.51 Gr @ 1.149-1.151” OAL for 124 Gr PD JHP.

Favorite of the Chief Petty Officers mess in the Navy on both ships I have was on. Good stuff. I tried it while in active duty but didn’t like but I’m now a 2-3 cup drinker after retiring from the Navy.

Depending on the load or ammo your shooting, you might not need to. The TSO comes with 3 recoil springs; 11, 13 and 16. The 16# comes installed in the gun and can be used with either 9 or .40 without any adverse effects. But you might have to use the lighter spring depending on your ammo or reloads if you do shoot your own reloads. I know my 9mm TSO didn’t have any problems with factory federal and Winchester ammo with the stock 16# recoil spring when I shot it out of the box.

Another vote for the TSO. Got one myself. Get the .40 instead of the 9mm. With the .40, you can buy the barrel and mags later on if you wat to shoot 9mm too. It’s simpler to go from .40 to 9mm compared to going from 9mm to .40.

Great job! You’re video tutorial made it look very easy to do. Showing also the materials and where you got them is a plus. Thank you very much.

I’m using 115 Gr RMR FMJ Rn and precision delta 115 JHP. No, my barrel hasn’t been throated or reamed.

I’m loading mine with 7.2 Gr CFE pistol at 1.155.

That has an old style trigger guard used by the older and the newest TSO. I have a TSO with that trigger guard while my cm has the new thinner .trigger guard

What were you trying to accomplish?

What size did you opened up your gas port to?

Get the CGW extended firing pin and reduced power firing pin spring. I’m currently using an 11.5# hammer spring from CGW and I don’t have any light strike problems using CCI primers or factory ammo.

What mounting system are you using on your pouches? Thanks.