haze10 Posted April 29, 2007 Share Posted April 29, 2007 Whats the best case lube out there and the easiest to use. How do you clean it off a finsihed round - want to progressive reload so the lube would be on the finished round. Link to comment Share on other sites More sharing options...
Shawn Knight Posted April 29, 2007 Share Posted April 29, 2007 I use Imperial Wax. You can apply it while you inspect your cases with just your finger tips. When the rounds are finished you dump them into a tumbler with coarse corn cob media and it will get the lube off. Link to comment Share on other sites More sharing options...
foxtrotuniformlima Posted April 29, 2007 Share Posted April 29, 2007 Best - Dillon Pump Easiest - Hornady One Shot For Rifle cases I really like the Dillon. I have never had a stuck case w/Dillon. Even using SB RCBS dies. My issue with it is makes a mess. It is lanolin in alcohol. Alcohol evaporates and lanolin lubes. The case feeder and tube on my Dillon need to be cleaned more often than with Oneshot. Link to comment Share on other sites More sharing options...
Run n Gun Posted April 29, 2007 Share Posted April 29, 2007 Honady One-Shot is the easiest to use and I've never had a .223 case stick with it, but others have... Ed Link to comment Share on other sites More sharing options...
EricW Posted April 29, 2007 Share Posted April 29, 2007 I've been through hell with One Shot and rifle brass. Stick with the Dillon (Lanolin Spray) - lasts forever, and works. I'm still on my first bottle. Link to comment Share on other sites More sharing options...
hopalong Posted April 29, 2007 Share Posted April 29, 2007 I've had great success with a muzzle loading product called bore butter. put a little on your hands and just pick your brass up and rub it all together. You'll have to lube the necks but I have yet to have any rifle brass stick (.223 up to .300 win mag). You'll want to tumble afterwards or not....it doesn't matter unless it is quite warm then it gets kind of "slick". Not the easiest, not the least messy, but unless your doing 500+ at a time no different than any other rifle case lubes. Hopalong Link to comment Share on other sites More sharing options...
et45 Posted April 29, 2007 Share Posted April 29, 2007 I like the Hornady One Shot also have never stuck one with it either. Link to comment Share on other sites More sharing options...
stubbicatt Posted April 30, 2007 Share Posted April 30, 2007 I like the Lee lube that comes in the toothpaste tube. If you mix it 10 to one with iso and put in a spray it is the poor man's Hornady One Shot. Even better, while I've stuck cases with the one shot, never stuck one yet with this stuff. FWIW. Link to comment Share on other sites More sharing options...
George Posted April 30, 2007 Share Posted April 30, 2007 Dillon spray lube is the best way to lube for rifle sizing on a progressive loader. If you are loading single stage and only a very small batch at a time (50-100), then the Imperial Sizing Wax is maybe the best choice, but for bulk, nothing beats the Dillon spray. Just leave the lube on and shoot them. If it bothers you, tumble them for 10-15 minutes. Link to comment Share on other sites More sharing options...
Bullzeye Posted April 30, 2007 Share Posted April 30, 2007 +1 on the Hornady One Shot. Love that stuff. Paul Link to comment Share on other sites More sharing options...
straightshooter1 Posted April 30, 2007 Share Posted April 30, 2007 I love the Hornady One Shot, but I have had a couple of stuck cases in 30'06 (and IIRC, one in 223), so I am using the Dillon for rifle IF I am full length resizing (which you need to do with an AR or other semi-auto). For neck sizing with a bolt action, the One Shot is perfect. Bob Link to comment Share on other sites More sharing options...
Bollocks Posted May 1, 2007 Share Posted May 1, 2007 Imperial Sizing Wax here at the moment but I also have good experiences with the dillon lube. Greetings from Holland, BolloX Link to comment Share on other sites More sharing options...
docatru Posted May 2, 2007 Share Posted May 2, 2007 You'll want to tumble afterwards or not....it doesn't matter unless it is quite warm then it gets kind of "slick". _____________ OK Here's my question. I'm new to reloading. Just to double check --- it is OK to tumble completed rounds in corn cob without any danger? Can the pointed tips of bullets strike primers? I'm currently reloading .223 and .45 LC - adding .308 and .45 ACP soon. Thanks, DOC Link to comment Share on other sites More sharing options...
ima45dv8 Posted May 3, 2007 Share Posted May 3, 2007 Can the pointed tips of bullets strike primers? I would characterize it as a "touch", rather than a "strike". I wouldn't worry about it. Link to comment Share on other sites More sharing options...
Shawn Knight Posted May 3, 2007 Share Posted May 3, 2007 Can the pointed tips of bullets strike primers? I would characterize it as a "touch", rather than a "strike". I wouldn't worry about it. Maybe more of massaging. Link to comment Share on other sites More sharing options...
benos Posted May 8, 2007 Share Posted May 8, 2007 Since I get this question a lot on the phone... For bottleneck cases and with either Dillon's spray or Hornady's One Shot, what is your preferred application method? How do you keep from getting too much lube on the shoulder? be Link to comment Share on other sites More sharing options...
GentlemanJim Posted May 9, 2007 Share Posted May 9, 2007 I put about 1 hundred in a shallow box..two squirts of dillon then roll and shake a bunch let dry a few...then run them thru. Jim Link to comment Share on other sites More sharing options...
D.Hayden Posted May 9, 2007 Share Posted May 9, 2007 (edited) First: I always use the Dillon spray.. I dump a hundred or so cases into a big plastic 'jar'.. maybe it's 1.5 gallions? give a little spray, shake repeat a couple times (maybe max 300-350 cases) If it feels rough going through the sizer, I add a little more. But it's really just a touch anyways.. Then I tumble ni CornCob, it removes the lube, and breaks off the little bits from the trimming.. Edited May 9, 2007 by BerKim Link to comment Share on other sites More sharing options...
George Posted May 9, 2007 Share Posted May 9, 2007 I have an old RCBS powder measure box lid that holds about 50 .223 cases laying on their sides (as many as I usually choose to size without a break). I spritz the batch with 2-3 pumps of the Dillon and shake the box like it's jiffy pop and let it sit for a few minutes. As each case is picked up, I roll it in my fingers to make sure the shoulder is lubed (my main issue is not too much there, but too little) and then press the neck over a brush I have threaded into a holder. That brush is spritzed with lube and this gets the expander ball lubed a little. I feel like this method gives me control over the lube applicattion and optimizes the die operation by lubing the expander ball so the case neck isn't scuffed badly on the inside. I only pay this kind of attention to rifle cases, pistol cases don't deserve this level of concern in most cases (pun intended). Link to comment Share on other sites More sharing options...
anyracoon Posted May 9, 2007 Share Posted May 9, 2007 I use a large Zip Lock Freezer bag, throw a couple of hand fulls of brass in, spray with one shot, close bag and shake. Than load, brass does not come in contact with any surfaces that would transfer any grit or dirt. Link to comment Share on other sites More sharing options...
benos Posted May 11, 2007 Share Posted May 11, 2007 Thanks for the details everyone. be Link to comment Share on other sites More sharing options...
RePete Posted May 11, 2007 Share Posted May 11, 2007 +2 for the Lee Case Lube. Best part is that you don't have to remove it after sizing and it doesn't degrade the powder or primer. Link to comment Share on other sites More sharing options...
steel1212 Posted May 24, 2007 Share Posted May 24, 2007 I've been using the frankford arsenal pump stuff. Just put the brass in a plastic box and spray. I don't tumble it off just run through like normal then shoot at the end. Link to comment Share on other sites More sharing options...
dhenry132 Posted June 18, 2009 Share Posted June 18, 2009 100% liquid lanolin 4 oz mixed with 20oz of isopropyl alcohol = > 99% Works better than most. I have stuck one case out of over 100000 cases Link to comment Share on other sites More sharing options...
uscbigdawg Posted June 18, 2009 Share Posted June 18, 2009 Dillon Case Lube and you're good to go. Rich Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now