Rifle/Shotgun

2,035 topics in this forum

1. 6.5 Creedmoor

   By prairiefire, February 26, 2014
   • 10 replies
   • 909 views
   • 
   • shootsforfun
   • April 21, 2014
2. • 
   • 
   • 

3. Need Varget?

   By Noximus03, April 6, 2014
   • 5 replies
   • 985 views
   • 
   • Noximus03
   • April 16, 2014

4. Small Magnum Primers

   By 02Fatboy, April 7, 2014
   • 20 replies
   • 1.1k views
   • 
   • 02Fatboy
   • April 15, 2014

5. Narrowing down powders

   By JeffJ99, April 9, 2014
   • 8 replies
   • 887 views
   • 
   • JeffJ99
   • April 11, 2014

6. Sizing 300 AAC

   By thl, April 8, 2014
   • 2 replies
   • 655 views
   • 
   • Tom Freeman
   • April 9, 2014

7. .223 Case Prep with Dillon Rapid Trim and lube die on 650?

   By zsavage81, March 18, 2014
   • 5 replies
   • 1.8k views
   • 
   • mgrs
   • April 6, 2014

8. cleaning brass (308) using the stainless steel tumbling

   By M ammo, February 25, 2014   

   • Squeaky clean
   • 14 replies
   • 1.3k views
   • 
   • Steve RA
   • April 5, 2014

9. What happened here

   By johnsons1480, March 20, 2014
   • 24 replies
   • 1.3k views
   • 
   • bigedp51
   • April 1, 2014

10. Dillon .223 carbide or steel resizer

    By Prebaned, March 29, 2014
    • 0 replies
    • 344 views
    • 
    • Prebaned
    • March 29, 2014

11. Dillon .223 carbide or steel resizer

    By Prebaned, March 29, 2014
    • 0 replies
    • 314 views
    • 
    • Prebaned
    • March 29, 2014

12. Resizing .223 on a progressive press 1 2

    By Overscore, March 10, 2014
    • 37 replies
    • 3.6k views
    • 
    • gigs
    • March 24, 2014

13. Problems with Montana Gold 223 Bullets? 1 2 3 4

    By blairmckenzie1, May 3, 2013
    • 85 replies
    • 10.5k views
    • 
    • Alaskapopo
    • March 22, 2014

14. 223/556 Chrono Data with AR COMP Powder

    By Taildraggerdave, September 5, 2011
    • 6 replies
    • 9.1k views
    • 
    • dauntedfuture
    • March 20, 2014

15. Wrong primers

    By 225 Fireman, March 19, 2014
    • 8 replies
    • 667 views
    • 
    • Alaskapopo
    • March 20, 2014

16. Cleaning Stained & Tarnished Brass

    By Reshoot, March 12, 2014   

    • Acid solution??
    • 23 replies
    • 2.1k views
    • 
    • DWFAN
    • March 14, 2014

17. Need advice for .308 head stamps

    By gatnfans, February 9, 2014
    • 6 replies
    • 1.9k views
    • 
    • rhett45acp
    • March 11, 2014

18. Optimum velocity for 69 grain .223 loads for an AR

    By SteveU, February 22, 2014   

    • 3 gun
    • 3-gun
    • 20 replies
    • 12.6k views
    • 
    • 38superman
    • March 7, 2014

19. 6.5 Creedmoor

    By prairiefire, March 3, 2014
    • 2 replies
    • 437 views
    • 
    • 427Cobra
    • March 5, 2014

20. 6.5 Creedmoor

    By prairiefire, March 3, 2014
    • 0 replies
    • 342 views
    • 
    • prairiefire
    • March 3, 2014

21. switching from a 2 die setup to a 3 die set-up (223)

    By usmc90, February 24, 2014
    • 15 replies
    • 847 views
    • 
    • fltbed
    • March 2, 2014

22. Starting loads for AR

    By Pasley, February 27, 2014
    • 3 replies
    • 759 views
    • 
    • Youngeyes
    • March 2, 2014

23. Case length vs velocity.

    By Therealkoop, February 18, 2014
    • 1 reply
    • 598 views
    • 
    • 427Cobra
    • February 26, 2014

24. Annealed Neck Color OK? - Slight Copper'ish Tint

    By Steve D., February 21, 2014
    • 1 reply
    • 522 views
    • 
    • jmorris
    • February 21, 2014

25. Belted mag powder system

    By bubba04, February 11, 2014
    • 12 replies
    • 828 views
    • 
    • Doc Hunter
    • February 17, 2014

26. Any pet loads for N540 and 77 grain SMK's

    By Alaskapopo, February 13, 2014
    • 5 replies
    • 817 views
    • 
    • Dan Sierpina
    • February 15, 2014