wyliearms Posted September 25, 2017 Share Posted September 25, 2017 Guys, if you have not tried Shooters World Clean Shot in your PCC you are missing out. I will try and take a picture of my comp after 3 matches using this powder. You do get some small goldish particles down in the lower but it is no where near as dirty as most of the other fast powders like TG. It burns really clean and is comparable to 231 as far as burn rate is concerned. It also meters like water. Link to comment
selecw Posted October 10, 2017 Share Posted October 10, 2017 Scorpion load for 16" barrel : 3.0 Autocomp with 147 Bayou comes in at 125PF. I tested 105, 120, 124, 147 and 160. This load gave me the least dot bounce at 25 yards. OAL is 1.160. I use Fiocchi SPP. This has proved totally reliable in USPSA matches to date. In fact I have only cleaned the gun once since buying it a year ago. The only issue - 147 Bayou don't run well in the CZC extensions. They bulge too much. The problem goes away with the Taylor Freelannce extension. Link to comment
Aircooled6racer Posted October 17, 2017 Share Posted October 17, 2017 Hello: Anyone have a good 124 grain load they like for there Sig MPX? I am using 115's right now but want to try some 124's or close to that. Thanks, Eric Link to comment
KzBoost Posted October 18, 2017 Share Posted October 18, 2017 Looking for suggestions on loading 9mm for PCC. Im using 124gr coated lead, VV N320, and a JP Barrel. Anyone got a suggestion that works well for them? My JP's chamber is really long, wondering on what OAL to go with. Link to comment
phoenixsomd Posted October 18, 2017 Share Posted October 18, 2017 Looking for suggestions on loading 9mm for PCC. Im using 124gr coated lead, VV N320, and a JP Barrel. Anyone got a suggestion that works well for them? My JP's chamber is really long, wondering on what OAL to go with.I'm using 135g Bayou RN coated bullets over 3.1g of e3. The OAL is 1.12 which is driven by getting reliable magazine feeding; Taylor Freelance extensions. Sent from my SM-G935V using Tapatalk Link to comment
L9X25 Posted October 18, 2017 Share Posted October 18, 2017 I have shot Winchester White Box ammo (115gr FMJ) that is commonly 1.165 - 1.170 long, through my Glock/TF mags, with my JP13, with no problems at all. The mags and rifle function perfectly at this length, although I would caution going any longer than that as there is not much room left in the magazines. Link to comment
Bwilmot Posted October 20, 2017 Share Posted October 20, 2017 (edited) Psa 16" tacfire bcg w/wieght removed MBX buffer system MBX Fang hiperfire 24c taccom small muzzle break 3.5 Titegroup under a 124gr RMR RN also. 3.8 Titegroup under a 115gr RMR RN depends on what Bullets I have at the time. Both loads you can feel in the shoulder but the dot barely moves. 20yd Bill Drill is with in 6" and .18-.20 splits Edited October 20, 2017 by Bwilmot Link to comment
Roons Posted October 20, 2017 Share Posted October 20, 2017 (edited) 1. PCC details, barrel length, brand and mods? JP GMR-15 14.5 barrel with pinned 3-port comp 2. Bullet weight, type and brand? 115 RN Blue Bullet 3. Powder and charge weight? 3.8 Titegroup 4. Primers? CCI Small Pistol 5. OAL? 1.150 6. Reliability? 100% 7. Accuracy? TBD 8. How does it shoot? Soft? Snappy? Slightly snappy 9. Split times? Below 0.15 10. Dot movement? Minimal I started with 3.4 Titegroup with a 125g RN Blue Bullet (everything else the same). While it feels soft, it had a more "push" feel to it. When I tried the 115 with 3.8 Titegroup, the GMR felt as it ran faster and the dot moved less. I'm now working on accuracy loads with different bullet manufacturers (Bayou 115 RNs and Xtreme 115 RN HPCB) in addition to reducing leading of the comp (not sure if Blue Bullets with Titegroup related). Hopefully the Xtreme HPCB or Bayou work out to reduce leading. I've used Bayou for years in Limited and would rather use them due to costs; however, accuracy will be key. Edited October 20, 2017 by Roons Link to comment
Tonka Posted October 23, 2017 Share Posted October 23, 2017 Sig MPX 16" with springer precision comp MG 121 4.2 N320 133 pf 1.130 length dot has very little movement but what there is, is straight up shots will touch if I'm doing my job Link to comment
jtrump Posted October 23, 2017 Share Posted October 23, 2017 (edited) Anyone have a few loads for a GMR-13/15 for a PD 115g JHP with titegroup? Roons should be close. I'm thinking about switching bullets, or should I stick with JHP? new to this pcc game. Seems as if the RN/FMJ seems to be more of the goto over the JHP. Edited October 23, 2017 by jtrump Link to comment
L9X25 Posted October 23, 2017 Share Posted October 23, 2017 I would start with Roons's load and chrono. I think that I may have the slowest barrel in history, so my charge weights might not be safe in a "normal" barrel. I started with 4.0 TG and a 115 FMJ @ 1.155" and it was way too slow, but it was a good starting point. You also want to load the JHP's shorter than FMJ because of the profile. Link to comment
IntenseImage Posted October 24, 2017 Share Posted October 24, 2017 1. AR9, 16" Faxon, NERD Comp, Taccom BCG, Blitzkrieg buffer, limited bolt travel too2. Xtreme 124 3. 3.7 WSF4. S&B5. 1.146. 100% reliable7. Haven't really tried for groups but it seems to be doing well8. Shoots pretty soft. Not all that snappy9. NA10. Easy to track as it goes high right and snaps back to center.1. MPX w 8" barrel and KVP Linear Comp2. Xtreme 1473. 3.7 WSF4. S&B5. 1.146. 100% reliable7. Again haven't shot groups but it's doing well8. It's an MPX ... It's soft no matter what!9. NA10. Dot really just vibratesDisclaimer ... I have no clue what PF these are doing in the PCCs. The 147 load is my normal uspsa/3gun load that makes a 130-132 in our M&Ps. If you noticed I just swap the heads from 147 to 124 for the AR9 as the dot tracking was simply better. I can also run the 124s in my MPX and it's stupidly soft.Sent from my SM-G955U using Tapatalk Link to comment
James3Gunna Posted October 24, 2017 Share Posted October 24, 2017 I have been running 3.9 gr of Titegroup behind 124 gr Xtreme RN bullets with great success in my MPX. Link to comment
Aircooled6racer Posted October 29, 2017 Share Posted October 29, 2017 Hello: Anyone have a good 135 grain plated bullet load for a Sig MPX? I shot some Freedom 135 reman loads in the MPX and they shot pretty good. The chrono showed a pretty wide spread on these so I want to load my own up. Thanks, Eric Link to comment
Shadyscott999 Posted October 29, 2017 Share Posted October 29, 2017 On 10/17/2017 at 7:25 PM, Aircooled6racer said: Hello: Anyone have a good 124 grain load they like for there Sig MPX? I am using 115's right now but want to try some 124's or close to that. Thanks, Eric 124 PD JHP @ 1.12 with 4.3 of HP38 is the cats ass out of an MPX with a taccom comp. Stupid flat and 140 pf Link to comment
Neomet Posted October 29, 2017 Share Posted October 29, 2017 34 minutes ago, Shadyscott999 said: 124 PD JHP @ 1.12 with 4.3 of HP38 is the cats ass out of an MPX with a taccom comp. Stupid flat and 140 pf 1.12?? Any particular reason why so short or just because? I'm headed out for some HP38 on Monday. Link to comment
Aircooled6racer Posted October 29, 2017 Share Posted October 29, 2017 Hello: I am loading my coated 115 grain bullets to 1.125" OAL. They seem to feed just fine and the bullet does not touch the lands. Going to try some HP38/231, Universal Clays, Tite Group and maybe some Unique. Thanks, Eric Link to comment
Neomet Posted October 29, 2017 Share Posted October 29, 2017 Cool. I have run my 115s and 121s at 1.135 and 1.145 and neither touches the lands. I was wondering if it was maybe for better feeding, but I was just pulling that out of the air. Link to comment
L9X25 Posted October 29, 2017 Share Posted October 29, 2017 9 minutes ago, Neomet said: Cool. I have run my 115s and 121s at 1.135 and 1.145 and neither touches the lands. I was wondering if it was maybe for better feeding, but I was just pulling that out of the air. When I got my JP I did not have a press set up to load 9mm, so I went to Wally World and purchased 1,000 rds of 115gr FMJ WWB. In the bulk packs that is loaded to 1.160 and, to my surprise, that works great in the mags and rifle. JP's are known for deep chambers and those were no problem. When I set-up the press, I left the OAL alone and it has worked great. YMMV. Link to comment
jtrump Posted October 29, 2017 Share Posted October 29, 2017 (edited) 1. GMR with blitzkrief buffer system 2. Precision Delta 115 JHP 3. 4.3g Titegroup 4. Win 5. 1.145 6. 100% reliable 7. Can shoot out a pasty at 25 yards when you turn the dot down 8. Titegroup has a little pop, the buffer system helps but the dot tracks great 9. NA 10. Nice up and down dot movement. I'm wanting to try some WSF Edited October 29, 2017 by jtrump Link to comment
nickbfishn Posted October 30, 2017 Share Posted October 30, 2017 I think I’ve found my steel load for my taccom ULW with Jp SCS (3 steel weights, 1 tungsten, green spring, h11 smalley spring) 124 rn bayou 3.2gr n320 1.12 oal I ran a full steel match yesterday without any hiccups and it shot soft and flat. I also loaded up some bayou 147’s with 2.7gr but did not try it because the 124’s were fantastic! Link to comment
gerritm Posted October 30, 2017 Share Posted October 30, 2017 For both of my PCC's. Taccom ULW with his light buffer and JP 14.5 barrel with pinned JP tactical comp with same Taccom ULW buffer. Steel load: 2.9grs Titegroup, 115gr SNS Casting RN, 1.12OAL Very soft, accurate, and reliable. USPSA load: 3.1grs Titegroup, 147gr SNS Casting RN, 1.12OAL. Red dot bounces a little more in the Taccom, but super soft in the JP barrel. gerritm Link to comment
KzBoost Posted October 31, 2017 Share Posted October 31, 2017 9 hours ago, nickbfishn said: I think I’ve found my steel load for my taccom ULW with Jp SCS (3 steel weights, 1 tungsten, green spring, h11 smalley spring) 124 rn bayou 3.2gr n320 1.12 oal I ran a full steel match yesterday without any hiccups and it shot soft and flat. I also loaded up some bayou 147’s with 2.7gr but did not try it because the 124’s were fantastic! what pf are you making with this load? Im working on my 125gr with 1.130 oal and 3.8gr n320. I'm hoping to land somewhere near 140pf with this on a 14.5" JP barrel. Link to comment
nickbfishn Posted October 31, 2017 Share Posted October 31, 2017 7 minutes ago, KzBoost said: what pf are you making with this load? Im working on my 125gr with 1.130 oal and 3.8gr n320. I'm hoping to land somewhere near 140pf with this on a 14.5" JP barrel. I have not chrono’d them yet as I made them strictly for steel. However, I suspect they’ll be at about 115-120pf. The rounds I made up for matches is the same as yours except mine are 1.12oal. I made these up based on a buddy who shoots production XDM with a 5.25” Barrel and he makes 130+/- so I suspect mine will be very similar. That load oit of your barrel should eaily hit 140, I would guess closer to 145. Link to comment
KzBoost Posted October 31, 2017 Share Posted October 31, 2017 (edited) 11 minutes ago, nickbfishn said: I have not chrono’d them yet as I made them strictly for steel. However, I suspect they’ll be at about 115-120pf. The rounds I made up for matches is the same as yours except mine are 1.12oal. I made these up based on a buddy who shoots production XDM with a 5.25” Barrel and he makes 130+/- so I suspect mine will be very similar. That load oit of your barrel should eaily hit 140, I would guess closer to 145. Thanks for the info! Any reason you're loading 1.120 and not longer? I was told to load as long as possible as long as it passes plunk test and feeds well. Edited October 31, 2017 by KzBoost Link to comment
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now