dillon Posted August 17, 2019 Share Posted August 17, 2019 For those interested, the XL750 manual is now added to the Dillon website; https://www.dillonprecision.com/manuals.html Link to comment Share on other sites More sharing options...
hrh Posted August 17, 2019 Share Posted August 17, 2019 (edited) I see the 750 has a "limited lifetime warranty". Dillon will either repair or replace defective parts on an exchange basis. I hope you don't have to send Dillon broken springs and other small parts to get replacements. Edited August 17, 2019 by hrh spelling Link to comment Share on other sites More sharing options...
Jim Watson Posted August 17, 2019 Share Posted August 17, 2019 On 8/16/2019 at 9:51 AM, Chills1994 said: Where are all the videos of people cranking out ammo on their new 750's? My thought exactly. Where's dub, he's had his for 11 days now. Link to comment Share on other sites More sharing options...
George16 Posted August 17, 2019 Share Posted August 17, 2019 16 hours ago, hrh said: I see the 750 has a "limited lifetime warranty". Dillon will either repair or replace defective parts on an exchange basis. I hope you don't have to send Dillon broken springs and other small parts to get replacements. What do you mean by limited lifetime warranty? The box has “No B.S. warranty” emblazoned on it just like the XL650. Link to comment Share on other sites More sharing options...
Chills1994 Posted August 18, 2019 Share Posted August 18, 2019 11 hours ago, Jim Watson said: My thought exactly. Where's dub, he's had his for 11 days now. I've had my second 650 for less time than that, and I have already cranked out some .308 Winchester rounds. Link to comment Share on other sites More sharing options...
MarilynMonbro Posted August 18, 2019 Share Posted August 18, 2019 On 8/16/2019 at 9:51 AM, Chills1994 said: Where are all the videos of people cranking out ammo on their new 750's? I'm getting mine this week but no case feeder. I plan on making a short video when I get the dies set Link to comment Share on other sites More sharing options...
Derek45 Posted August 20, 2019 Share Posted August 20, 2019 I can't help but wonder, if the redesigned primer system was driven by liability and rumor or 650 primer kabooms. My 650 is several years old, and primes more reliably than my 550b Watching the way some you-tubers slam the machine up & down, I don't blame Dillon. ...I plan on keeping my 650 for a long time. Link to comment Share on other sites More sharing options...
dillon Posted August 20, 2019 Share Posted August 20, 2019 Dillon will continue to replace small parts, such as springs, ring indexers, nylon parts, etc, without requiring the damaged parts be sent in. On some larger parts, such as shellplates, powder measures, we reserve the right to have the damaged part sent in first, before a replacement is sent. This allows us to ensure the part being replaced is actually a Dillon OEM part, that the part was damaged or broken, and not lost (lost parts are not covered under warranty), and that the damage is not due to misuse (such as adding a auto drive), and so R&D can examine the damage, to see if changes should be made to a part design. Link to comment Share on other sites More sharing options...
hrh Posted August 21, 2019 Share Posted August 21, 2019 9 hours ago, dillon said: Dillon will continue to replace small parts, such as springs, ring indexers, nylon parts, etc, without requiring the damaged parts be sent in. On some larger parts, such as shellplates, powder measures, we reserve the right to have the damaged part sent in first, before a replacement is sent. This allows us to ensure the part being replaced is actually a Dillon OEM part, that the part was damaged or broken, and not lost (lost parts are not covered under warranty), and that the damage is not due to misuse (such as adding a auto drive), and so R&D can examine the damage, to see if changes should be made to a part design. Thanks for clarifying that. Link to comment Share on other sites More sharing options...
George16 Posted August 21, 2019 Share Posted August 21, 2019 On 8/19/2019 at 8:39 PM, Derek45 said: My 650 is several years old, and primes more reliably than my 550b ...I plan on keeping my 650 for a long time. I’m hoping so too. I just got a brand new 650 for a very nice price and just finish mounting it yesterday next to my 550. Of by the way, kudos to Dillons customer service. I had a very old powder measure for my 550 that doesn’t have the fail safe rod giving me fits with the clanking. I said enough with it and decided to call Dillon last week and asked what to do. Ron, told me told that since I have the old powder measure; just gave me an rma to box and send it back to them to be replaced with a new one. New replacement powder measure will be arriving Friday according to fedex. Thanks Dillon. Link to comment Share on other sites More sharing options...
dfox Posted August 23, 2019 Share Posted August 23, 2019 I just got a xl750 and because of the new angle of the powder measure and it’s return rod you cannot run a powder check and bullet feeder together on this machine. The new priming system is a little better but I never had a problem with the xl 650 priming system. I will have to use a different powder measure if I want to use powder check and mr bullet feeder. Maybe not a big deal but to some it maybe. Now if someone would design a tool head to use bullet feeding through a station of its own that would be ideal. Link to comment Share on other sites More sharing options...
dogdoc1 Posted August 23, 2019 Share Posted August 23, 2019 Dfox could you run an rcbs lockout die (powder check) with your bullet feeder? Is the priming system as reliable as the 650s? thanks dogdoc Link to comment Share on other sites More sharing options...
dfox Posted August 23, 2019 Share Posted August 23, 2019 The problem is the angle of the powder measure. When the powder slide goes back it hits the mr bullet feeder. The xl650 powder measure points in a different direction so it clears everything. The priming system works great. I’ll see about posting a picture of the problem. Link to comment Share on other sites More sharing options...
Superpipe9 Posted August 24, 2019 Share Posted August 24, 2019 On 8/23/2019 at 8:59 AM, dfox said: The problem is the angle of the powder measure. When the powder slide goes back it hits the mr bullet feeder. The xl650 powder measure points in a different direction so it clears everything. The priming system works great. I’ll see about posting a picture of the problem. So can you still run a bullet feeder without problem or is this a issue? I don’t run a powder check so not worried about that. How is the rest of the press? Is it a worthy upgrade or should people just stick with a xl650. Thanks Link to comment Share on other sites More sharing options...
dfox Posted August 25, 2019 Share Posted August 25, 2019 You can run bullet feeder right after powder measure and not use a powder check.. press runs great, primer system I like a little better than the xl 650. I also bought the variable speed case feeder . I don’t see any difference in reliability over the standard. I used a Mark 7 autodrive on the xl650 and the std case feeder ran fine. On my xl650 I used snowshooze ( eBay) mods for 100.00 and it made it a great machine. I think with the snowshooze mods the xl650 is as good as the xl750 and the xl650 you can run powder check and bullet feeder with no interference. For now I am running a Hornady powder measure and everything works like I want it to. Maybe Dillion will come up with a fix or even the snowshooze guy might. Don’t think I would have upgraded from my xl650 to the xl750 knowing what I know now. Link to comment Share on other sites More sharing options...
KaNooM Posted December 7, 2019 Share Posted December 7, 2019 On 7/25/2019 at 3:34 PM, 223to45 said: Good, maybe I can pick up some 650's cheap when people upgrade Sent from my SM-G930V using Tapatalk I’ll sell mine new never used Link to comment Share on other sites More sharing options...
jejb Posted December 7, 2019 Share Posted December 7, 2019 On 8/24/2019 at 8:33 PM, dfox said: You can run bullet feeder right after powder measure and not use a powder check.. press runs great, primer system I like a little better than the xl 650. I also bought the variable speed case feeder . I don’t see any difference in reliability over the standard. I used a Mark 7 autodrive on the xl650 and the std case feeder ran fine. On my xl650 I used snowshooze ( eBay) mods for 100.00 and it made it a great machine. I think with the snowshooze mods the xl650 is as good as the xl750 and the xl650 you can run powder check and bullet feeder with no interference. For now I am running a Hornady powder measure and everything works like I want it to. Maybe Dillion will come up with a fix or even the snowshooze guy might. Don’t think I would have upgraded from my xl650 to the xl750 knowing what I know now. Thanks for the honest review. I've heard that same conclusion from a couple of guys at the range too. I'm sure the 750 is a good machine and would certainly be the one I'd buy if I were in that market. But it makes little to no sense to get rid of a working 650 to get one, IMO. Link to comment Share on other sites More sharing options...
jejb Posted December 7, 2019 Share Posted December 7, 2019 On 8/23/2019 at 6:34 AM, dogdoc1 said: Dfox could you run an rcbs lockout die (powder check) with your bullet feeder? Is the priming system as reliable as the 650s? thanks dogdoc If you run the RCBS seating/crimping die, it opens up a station. Works great on my 650. Link to comment Share on other sites More sharing options...
looking4reloadingdeals Posted December 7, 2019 Share Posted December 7, 2019 If you run the RCBS seating/crimping die, it opens up a station. Works great on my 650.Only problem is you can’t seat and crimp in the same step with lead/coated bullets, it causes lead shaving. But, that would affect the guys running lead/coatedSent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
jejb Posted December 15, 2019 Share Posted December 15, 2019 On 12/7/2019 at 9:54 AM, looking4reloadingdeals said: Only problem is you can’t seat and crimp in the same step with lead/coated bullets, it causes lead shaving. But, that would affect the guys running lead/coated I did not know that, thanks. I've only ever loaded copper coated bullets over the last 30 years or so of loading. Link to comment Share on other sites More sharing options...
looking4reloadingdeals Posted December 15, 2019 Share Posted December 15, 2019 I did not know that, thanks. I've only ever loaded copper coated bullets over the last 30 years or so of loading.No problem. IIRC, it’s because when doing both steps at once, the case can start being crimped before the bullet is fully seated, which causes the case to lose its bell obviously and can catch the side of the billet causing lead scraping. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
DubfromGA Posted February 23, 2020 Share Posted February 23, 2020 On 8/17/2019 at 7:01 PM, Jim Watson said: My thought exactly. Where's dub, he's had his for 11 days now. Mine is still sitting in the box......waiting on me to set it...and the new 550C up. Between working 13+ hour shifts and assisting my with through her battle with cancer there hasn't been much time for anything. It's comical how few range sessions I've had in the last year+. On the sidelines, waiting to get in the game. I have a long weekend off next weekend. If things line up like I hope....then I may get some progress on getting it done. I really want to get it cranking out good ammo before the 750B is released, lol. I have been ordering some powder, primers and such. Link to comment Share on other sites More sharing options...
EEH Posted February 23, 2020 Share Posted February 23, 2020 Shooting and reloading would be the last thing on my mind in your case. Good luck Link to comment Share on other sites More sharing options...
DubfromGA Posted February 24, 2020 Share Posted February 24, 2020 9 hours ago, EEH said: Shooting and reloading would be the last thing on my mind in your case. Good luck Thank you. Reading these forums, manuals, load data and such has been a pleasant distraction when time allows. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now