PA_USPSA Posted October 10, 2023 Share Posted October 10, 2023 I'm using a CZ Custom 13# hammer spring with a stock firing pin and reduced firing pin spring and haven't had any issues with CCI and Winchester primers. Link to comment Share on other sites More sharing options...
Stafford Posted October 10, 2023 Author Share Posted October 10, 2023 1 hour ago, ColoradoNick said: Who makes a 14? What is stock? I’m using CCI’s and Fiocchi’s so I will test. With the extended firing pin I’ve had zero issues with the 11.5# I think the S2 is a 14 stock. Don't know about the compact. Link to comment Share on other sites More sharing options...
ColoradoNick Posted October 10, 2023 Share Posted October 10, 2023 4 hours ago, PA_USPSA said: I'm using a CZ Custom 13# hammer spring with a stock firing pin and reduced firing pin spring and haven't had any issues with CCI and Winchester primers. Good to know. I'm going to go ahead and do the entire cajun package minus the extended firing pin. I'll post up thoughts afterwards. I'm going to try and put 1000 rounds through it first. Link to comment Share on other sites More sharing options...
ramnj Posted October 11, 2023 Share Posted October 11, 2023 (edited) 11 hours ago, ColoradoNick said: ...but I’m debating doing the full cajun gun works package minus the extended firing pin or just a flat trigger and short reset disconnect. Thoughts? From what I can tell the extended firing pin is the only thing they don’t recommend for a carry gun. If I don’t go lighter than the 13# main spring reliability should be fine correct? I installed the CGW Pro package with the 11.5lbs main spring and the CGW flat trigger on my S2C after about 100 rounds. It now has over 1k rounds of 115gr, 124gr and 147gr. I carry it with Underwood Defense ammo. I’ve used it in IDPA and Steel Challenge but haven’t shot it yet in USPSA. It’s been very reliable and haven’t had a FTF/FTE. I carry it in decock position. Edited October 11, 2023 by ramnj Link to comment Share on other sites More sharing options...
ColoradoNick Posted October 11, 2023 Share Posted October 11, 2023 30 minutes ago, ramnj said: I installed the CGW Pro package with the 11.5lbs main spring and the CGW flat trigger on my S2C after about 100 rounds. It now has over 1k rounds of 115gr, 124gr and 147gr. I carry it with Underwood Defense ammo. I’ve used it in IDPA and Steel Challenge but haven’t shot it yet in USPSA. It’s been very reliable and haven’t had a FTF/FTE. I carry it in decock position. Thanks! Link to comment Share on other sites More sharing options...
ES13Raven Posted November 15, 2023 Share Posted November 15, 2023 On 8/26/2023 at 2:42 PM, eerw said: with 14rnd CZ mag @eerw Stuart, are there any thin basepads that you know of, that will work with the old 14-round magazines, and still fit the IDPA CCP box? Link to comment Share on other sites More sharing options...
1911vm Posted November 15, 2023 Share Posted November 15, 2023 Does a shadow 2 safety fit the compact? Link to comment Share on other sites More sharing options...
Douglee25 Posted November 15, 2023 Share Posted November 15, 2023 25 minutes ago, 1911vm said: Does a shadow 2 safety fit the compact? Or the decocker from the P01? Link to comment Share on other sites More sharing options...
ben370 Posted November 15, 2023 Share Posted November 15, 2023 On 10/10/2023 at 12:19 PM, eerw said: old style 14rnd mag is fine. just have to find them. hahaha this is going to be unfair in idpa Link to comment Share on other sites More sharing options...
Racinready300ex Posted November 15, 2023 Share Posted November 15, 2023 11 minutes ago, ben370 said: hahaha this is going to be unfair in idpa I don't know, the ultimate gamer is a 38oz 2011. Or a steel framed P01. Link to comment Share on other sites More sharing options...
eerw Posted November 15, 2023 Share Posted November 15, 2023 3 hours ago, ES13Raven said: @eerw Stuart, are there any thin basepads that you know of, that will work with the old 14-round magazines, and still fit the IDPA CCP box? with CZ 14rnd mag. we have this pad that seems to fit the box with the factory sight. Link to comment Share on other sites More sharing options...
ramnj Posted November 15, 2023 Share Posted November 15, 2023 2 hours ago, 1911vm said: Does a shadow 2 safety fit the compact? Yes it does. I have it installed on mine. Link to comment Share on other sites More sharing options...
1911vm Posted November 15, 2023 Share Posted November 15, 2023 11 minutes ago, ramnj said: Yes it does. I have it installed on mine. 12 minutes ago, ramnj said: Yes it does. I have it installed on mine. Perfect thank you Link to comment Share on other sites More sharing options...
Andy9 Posted November 17, 2023 Share Posted November 17, 2023 Has anyone worked on a reduced weight slide spring? IDPA PF for CCP is 105 and working a light load i don't get a consistent full slide cycle. It comes with the captured flat spring, and it doesn't look like it can be taken apart easily. Link to comment Share on other sites More sharing options...
CZsandSigs Posted November 17, 2023 Share Posted November 17, 2023 27 minutes ago, Andy9 said: Has anyone worked on a reduced weight slide spring? IDPA PF for CCP is 105 and working a light load i don't get a consistent full slide cycle. It comes with the captured flat spring, and it doesn't look like it can be taken apart easily. I received from CGW today my SS guide rod and 13# P07 / P10C recoil spring (that's what works in a S2C per CGWs website) that I've seen suggested elsewhere but haven't had a chance to try it yet. Might / probably need to go lighter for a PF that low. Link to comment Share on other sites More sharing options...
msr Posted November 29, 2023 Share Posted November 29, 2023 (edited) The flat safety is not working for me. On the wait list for a left side extended safety. Are these showing up at all in the US or have they been completely unavailable. Edited November 29, 2023 by msr Link to comment Share on other sites More sharing options...
ramnj Posted November 29, 2023 Share Posted November 29, 2023 4 hours ago, msr said: The flat safety is not working for me. On the wait list for a left side extended safety. Are these showing up at all in the US or have they been completely unavailable. I ordered mine from Eric Graffel’s store in France. Link to comment Share on other sites More sharing options...
GJM Posted December 23, 2023 Share Posted December 23, 2023 The DA pull on mine is just over 9 pounds, SA feels good. If I wanted to reduce the DA, and maintain full reliability, is 15 the way to go, and is the part the same as for a regular Shadow 2? Anything else I would need to change? Link to comment Share on other sites More sharing options...
ColoradoNick Posted December 23, 2023 Share Posted December 23, 2023 35 minutes ago, GJM said: The DA pull on mine is just over 9 pounds, SA feels good. If I wanted to reduce the DA, and maintain full reliability, is 15 the way to go, and is the part the same as for a regular Shadow 2? Anything else I would need to change? If you’re talking about a main spring a 13# ignites everything I have tried. Link to comment Share on other sites More sharing options...
ColoradoNick Posted December 23, 2023 Share Posted December 23, 2023 36 minutes ago, GJM said: The DA pull on mine is just over 9 pounds, SA feels good. If I wanted to reduce the DA, and maintain full reliability, is 15 the way to go, and is the part the same as for a regular Shadow 2? Anything else I would need to change? If you’re talking about a main spring a 13# ignites everything I have tried. Link to comment Share on other sites More sharing options...
HesedTech Posted December 23, 2023 Share Posted December 23, 2023 3 hours ago, GJM said: Anything else I would need to change? Like the bigger brother, there are internal parts (besides the main spring) which need to be polished or changed if you want to optimize the trigger pull. Check with Cajon GW if you don't want to do the work yourself. Link to comment Share on other sites More sharing options...
msr Posted December 26, 2023 Share Posted December 26, 2023 Any update on holster availability? Link to comment Share on other sites More sharing options...
ES13Raven Posted December 26, 2023 Share Posted December 26, 2023 2 minutes ago, msr said: Any update on holster availability? Red Hill Tactical and Legacy Firearms have S2C holsters. Link to comment Share on other sites More sharing options...
shotgunone Posted December 30, 2023 Share Posted December 30, 2023 On 11/15/2023 at 3:59 PM, eerw said: with CZ 14rnd mag. we have this pad that seems to fit the box with the factory sight. So where do you find these 14 round mags? I know CZ's have several different mags for different guns. Which one's are these? Link to comment Share on other sites More sharing options...
eerw Posted December 30, 2023 Share Posted December 30, 2023 New 14 are harder to find, as CZ changed to the 15rnd mag about two years ago. rami 14 mags seem to be still in stock and take off the sleeve and they seem to work. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now