Johnnymazz Posted July 10, 2021 Share Posted July 10, 2021 11 hours ago, HOGRIDER said: The reason I asked was that a couple of days ago I decided to clean my primer pickup tubes and primer system magazine, and I noticed the magazine took several alcohol patches to clean all the primer residue out. I only use Federal Match primers, and have loaded less than 5,000 rounds.......... All reloaded brass is processed off-machine. Right now I'm wondering if I need to remove the Primer Slide Indexing Assembly and the Primer Slide in order to clean the Slide track of any residue/debris? Also wondering if the slide track can be successfully cleaned without removing the shell plate? Thanks! Watch the video, after you do it a few times. It only takes 20 minutes for a full teardown and cleaning. I also grease the zerk fittings. Good luck Link to comment Share on other sites More sharing options...
Johnnymazz Posted July 10, 2021 Share Posted July 10, 2021 Just now, Johnnymazz said: Watch the video, after you do it a few times. It only takes 20 minutes for a full teardown and cleaning. I also grease the zerk fittings. Good luck Also wipe everything down with alcohol Link to comment Share on other sites More sharing options...
Johnnymazz Posted July 10, 2021 Share Posted July 10, 2021 Another thing I did was polish the primer bar. That intales wet sanding it with 1000 grit sand paper followed by 2000 grit then 3000 grit. Also do the machine itself. Your primer bar will slide like butter after that. Link to comment Share on other sites More sharing options...
ddc Posted July 10, 2021 Share Posted July 10, 2021 (edited) @Cuzwhere did all the powder go? 125 rounds is a lot of powder.... just sayin... Edited July 10, 2021 by ddc Link to comment Share on other sites More sharing options...
HOGRIDER Posted July 10, 2021 Share Posted July 10, 2021 56 minutes ago, Johnnymazz said: Also wipe everything down with alcohol Thanks for all the info! Link to comment Share on other sites More sharing options...
Johnnymazz Posted July 10, 2021 Share Posted July 10, 2021 9 hours ago, HOGRIDER said: Thanks for all the info! Np, the RL1100 is a fine loading machine, it just needs proper maintenance and adjustments to keep it running smoothly. Link to comment Share on other sites More sharing options...
Johnnymazz Posted July 10, 2021 Share Posted July 10, 2021 9 hours ago, HOGRIDER said: Thanks for all the info! Np, the RL1100 is a fine loading machine, it just needs proper maintenance and adjustments to keep it running smoothly. Link to comment Share on other sites More sharing options...
Johnnymazz Posted July 10, 2021 Share Posted July 10, 2021 One last tip, when you remove the index paw, file down the sharp edges, this will keep the indexing running smoothly Link to comment Share on other sites More sharing options...
Cuz Posted July 10, 2021 Author Share Posted July 10, 2021 10 hours ago, ddc said: @Cuzwhere did all the powder go? 125 rounds is a lot of powder.... just sayin... Right into the bin with the loaded rounds. Normally I dump that bin into another bin every 25-30 rounds, but I was going for the record to see how fast I could load 100. I guess it’s time to order the Hornady collet bullet puller and to dust off the single stage press a friend gave me some years ago. Never thought I’d be using it. Link to comment Share on other sites More sharing options...
clw42 Posted February 2, 2022 Share Posted February 2, 2022 So, a little thread resurrection since this seems to be the most pertinent place to put this. I just received and installed my 1100. I decided to remove the ratchet to make it more like my 650. I've seen several posts about this process and I'm a bit confused. All I did was remove the ratcheting mechanism from the tool head and it no longer ratchets. I've seen posts saying that the coinciding parts on the press are to be removed as well. Is there a reason for this? I'll also add, that using the 1100 then going back to the 650 was a bit of a surprise. It's much beefier in operation and build quality. I've obviously seen folks make those same comments, but experiencing it was a little eye opening. Link to comment Share on other sites More sharing options...
Cuz Posted February 2, 2022 Author Share Posted February 2, 2022 4 hours ago, clw42 said: So, a little thread resurrection since this seems to be the most pertinent place to put this. I just received and installed my 1100. I decided to remove the ratchet to make it more like my 650. I've seen several posts about this process and I'm a bit confused. All I did was remove the ratcheting mechanism from the tool head and it no longer ratchets. I've seen posts saying that the coinciding parts on the press are to be removed as well. Is there a reason for this? I'll also add, that using the 1100 then going back to the 650 was a bit of a surprise. It's much beefier in operation and build quality. I've obviously seen folks make those same comments, but experiencing it was a little eye opening. you can do it either way. Some folks take off the ratchet from the toolhead. Others think that may weaken the bolt that works the primer slide because now it screws in further. Or you can take out the ratchet part of the press and leave the part on the toolhead. somewhere there is a whole discussion on this subject, but I don’t recall where at the moment. Link to comment Share on other sites More sharing options...
ddc Posted February 2, 2022 Share Posted February 2, 2022 Just now, Cuz said: you can do it either way. Some folks take off the ratchet from the toolhead. Others think that may weaken the bolt that works the primer slide because now it screws in further. Or you can take out the ratchet part of the press and leave the part on the toolhead. somewhere there is a whole discussion on this subject, but I don’t recall where at the moment. I've done it both ways. And then ended up removing everything ratchet related. The less crap to collect crap the better. I did put a washer behind the primer slide bolt to approximate the original orientation and geometry. Link to comment Share on other sites More sharing options...
clw42 Posted February 2, 2022 Share Posted February 2, 2022 24 minutes ago, Cuz said: you can do it either way. Some folks take off the ratchet from the toolhead. Others think that may weaken the bolt that works the primer slide because now it screws in further. Or you can take out the ratchet part of the press and leave the part on the toolhead. somewhere there is a whole discussion on this subject, but I don’t recall where at the moment. Yeah, that's where I was reading about it. You and ddc...the same guys responding to me here. 21 minutes ago, ddc said: I've done it both ways. And then ended up removing everything ratchet related. The less crap to collect crap the better. I did put a washer behind the primer slide bolt to approximate the original orientation and geometry. That's a good point about less crap to collect crap. I guess I'll do both. I did add washers to mimic the thickness of ratchet as well. I saw that in the other thread and figured I'd do the same. Thanks guys!! Link to comment Share on other sites More sharing options...
George16 Posted February 2, 2022 Share Posted February 2, 2022 I removed everything ratchet related for simplicity and less things to worry about. I mainly use my 1100 for processing and loading 9mm and .223. Link to comment Share on other sites More sharing options...
clw42 Posted February 2, 2022 Share Posted February 2, 2022 22 minutes ago, George16 said: I removed everything ratchet related for simplicity and less things to worry about. I mainly use my 1100 for processing and loading 9mm and .223. That's exactly what I'm using it for. Link to comment Share on other sites More sharing options...
Cuz Posted February 9, 2022 Author Share Posted February 9, 2022 On 2/2/2022 at 1:16 PM, ddc said: I've done it both ways. And then ended up removing everything ratchet related. The less crap to collect crap the better. I did put a washer behind the primer slide bolt to approximate the original orientation and geometry. This is probably what I’ll do too the next time I clean the press. I should be getting a light kit in soon so that will motivate me to take it apart. Link to comment Share on other sites More sharing options...
clw42 Posted February 9, 2022 Share Posted February 9, 2022 2 hours ago, Cuz said: This is probably what I’ll do too the next time I clean the press. I should be getting a light kit in soon so that will motivate me to take it apart. I ended up doing it. One screw to take off the frame mounted parts, and the ratchet from the tool head. Super smooth! Link to comment Share on other sites More sharing options...
clw42 Posted February 20, 2022 Share Posted February 20, 2022 Just curious if anyone is using the number 5 or the number 3 shell plate for both 9mm and 223? The 5 seems to be a little more snug for both size cases, but I'm not sure if that's okay for the 9mm. Link to comment Share on other sites More sharing options...
XL6504ME Posted February 21, 2022 Share Posted February 21, 2022 On 2/19/2022 at 4:40 PM, clw42 said: Just curious if anyone is using the number 5 or the number 3 shell plate for both 9mm and 223? The 5 seems to be a little more snug for both size cases, but I'm not sure if that's okay for the 9mm. I didn't know that was possible learn something new everyday. Link to comment Share on other sites More sharing options...
clw42 Posted February 21, 2022 Share Posted February 21, 2022 6 hours ago, XL6504ME said: I didn't know that was possible learn something new everyday. With my 650, I used the #5 for both, but the fit wasn't quite as snug on the 9mm as it is with the 1100 shell plate Link to comment Share on other sites More sharing options...
AHI Posted February 21, 2022 Share Posted February 21, 2022 1050/1100 shell plates are maid a different way 9 than 550,650,750.( More like a true shell holder) 9mm shell plate #5 223 shell plate #3 both use #3 buttons. Link to comment Share on other sites More sharing options...
clw42 Posted February 22, 2022 Share Posted February 22, 2022 Case feeder crapped out on me today. Got almost a month out of it before it died. Not sure how that stacks up. Luckily I was able to move the one from my 650 over. So needless to say, I'm not a fan of this new variable speed feeder. My 650 case feeder with the high/low setting (newer old style with the all plastic hopper) has been great, no issues whatsoever in five or six years. Link to comment Share on other sites More sharing options...
jejb Posted February 23, 2022 Share Posted February 23, 2022 That sucks. How much is the new motor? FWIW, mine has been fine since buying my RL1100 new last August. At least 10K rounds of 9mm and .223 through it. Link to comment Share on other sites More sharing options...
Boomstick303 Posted February 23, 2022 Share Posted February 23, 2022 21 hours ago, clw42 said: Got almost a month out of it before it died If your press is fairly new I would contact Dillon. Link to comment Share on other sites More sharing options...
clw42 Posted February 23, 2022 Share Posted February 23, 2022 8 minutes ago, Boomstick303 said: If your press is fairly new I would contact Dillon. Oh yeah, I did that immediately. I have a service ticket already, just waiting to hear back from them. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now