mikey_golds Posted May 27, 2020 Share Posted May 27, 2020 55 minutes ago, mayassa said: Search this channel https://www.youtube.com/watch?v=eUW9kh5Esok&t=429s. He has a couple of set up videos. I think you could have any questions answered with a facetime. oh for sure i watched like all of gavins stuff, just figured someone relatively close i shot one other NJ guy in here a PM could run me through the quirks they worked out . Link to comment Share on other sites More sharing options...
MikeyScuba Posted May 27, 2020 Share Posted May 27, 2020 I’m starting to get a little pi**ed off as I’m missing a case feeder pole and a mounting plate (international unit). Not sure why Misty is having problems finding my unit (??) but the fact I had to load 1100 rounds on my 650 is getting tiresome. And my revo pro is sitting right next to my 650..... Link to comment Share on other sites More sharing options...
DJRyan13 Posted May 27, 2020 Share Posted May 27, 2020 20 minutes ago, MikeyScuba said: I’m starting to get a little pi**ed off as I’m missing a case feeder pole and a mounting plate (international unit). Not sure why Misty is having problems finding my unit (??) but the fact I had to load 1100 rounds on my 650 is getting tiresome. And my revo pro is sitting right next to my 650..... They don’t have the best quality control. When I ordered my first Revo, they sent me the big case feeder when I paid for the small one. I did the right thing and told them.. They also forgot to send me a powder measure in that order. Second Revo went better. They need someone to initial the purchase order when they pack and maybe have someone do a second review. They will set it straight. Link to comment Share on other sites More sharing options...
Lyle2231 Posted June 2, 2020 Share Posted June 2, 2020 Regarding the manual machines, has anyone obtained a .223 Rem machine? How’s it working out? Link to comment Share on other sites More sharing options...
mikey_golds Posted June 3, 2020 Share Posted June 3, 2020 19 hours ago, Lyle2231 said: Regarding the manual machines, has anyone obtained a .223 Rem machine? How’s it working out? i have a second toolhead for .223 all good Link to comment Share on other sites More sharing options...
OptimiStick Posted June 3, 2020 Share Posted June 3, 2020 On 5/26/2020 at 8:08 PM, DJRyan13 said: They don’t have the best quality control. When I ordered my first Revo, they sent me the big case feeder when I paid for the small one. I did the right thing and told them.. They also forgot to send me a powder measure in that order. Second Revo went better. They need someone to initial the purchase order when they pack and maybe have someone do a second review. They will set it straight. I ordered a a new primer guide - that little plastic guide piece for the primer collator, and some extra nylon-tipped screws for the shell-plate nut. so like....$20 worth of stuff? and they sent me a new bullet-sense and mirror. Heh. Link to comment Share on other sites More sharing options...
Thetimb Posted June 21, 2020 Share Posted June 21, 2020 On 6/3/2020 at 3:46 PM, OptimiStick said: I ordered a a new primer guide - that little plastic guide piece for the primer collator, and some extra nylon-tipped screws for the shell-plate nut. so like....$20 worth of stuff? and they sent me a new bullet-sense and mirror. Heh. Bank error In your favor. Link to comment Share on other sites More sharing options...
MikeyScuba Posted June 21, 2020 Share Posted June 21, 2020 I figured out Friday I have decap sense installed but I didn’t order it. Did anyone get primer sense installed from factory? That was my first stab at my putting my machine together - by taking it apart lol. I discovered a week before I had the wrong case feed tube and the initial shipment of missing parts had the wrong pole setup for the bulletfeeder pro. Just got my amazon order of red’n’tacky, starett oil, grease gun and syringe. I preprocess my brass so decap sense isn’t needed. Link to comment Share on other sites More sharing options...
slavex Posted June 22, 2020 Share Posted June 22, 2020 @MikeyScuba what syringe did you order? I got 3 off Amazon but they won't reach through the core to get to the crank grease point unless I remove the grease zerk from the swage cam. I have a gen 1 core without the oval access hole in it, mine is just round and lines up directly to the pin that needs greasing. The newer cores have an oval hole and allows the syringe easier access Link to comment Share on other sites More sharing options...
MikeyScuba Posted June 22, 2020 Share Posted June 22, 2020 https://www.amazon.ca/gp/product/B07SF8JYQS/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 I have not checked yet to see if it fits. Link to comment Share on other sites More sharing options...
slavex Posted June 23, 2020 Share Posted June 23, 2020 @MikeyScuba I ordered mine from Amazon USA got 4 for the same price, but if yours fits better I'll probably just order a couple from Amazon CA Link to comment Share on other sites More sharing options...
Thetimb Posted June 23, 2020 Share Posted June 23, 2020 On 6/22/2020 at 1:26 AM, slavex said: @MikeyScuba what syringe did you order? I got 3 off Amazon but they won't reach through the core to get to the crank grease point unless I remove the grease zerk from the swage cam. I have a gen 1 core without the oval access hole in it, mine is just round and lines up directly to the pin that needs greasing. The newer cores have an oval hole and allows the syringe easier access are you using moly grease on that swage zerk or red and tacky? Link to comment Share on other sites More sharing options...
slavex Posted June 24, 2020 Share Posted June 24, 2020 Red and Tacky everywhere that needs grease. Link to comment Share on other sites More sharing options...
JatCarver Posted August 2, 2020 Share Posted August 2, 2020 I searched the thread and couldn’t find it. Can anyone point me toward pics or video of a Evo with the on board primer collator? I’m considering upgrading from my mk7 1050.... Link to comment Share on other sites More sharing options...
slavex Posted August 3, 2020 Share Posted August 3, 2020 there is a new collator coming for the Evo, there are some pics of it around somewhere Link to comment Share on other sites More sharing options...
JatCarver Posted August 4, 2020 Share Posted August 4, 2020 Looking for the one they currently have. Link to comment Share on other sites More sharing options...
TheStagePlan Posted August 4, 2020 Share Posted August 4, 2020 (edited) Quick Update Last Friday I order a Mark7 Evolution from Shooters Connection, 5 days later it arrived in the west coast total setup time was about 3 hours. other then a molex cable that was pinned incorrectly on the primer sense the machine has been running flawlessly. Here is a quick video of it running around 800 rounds per hour. Mark 7 evo + auto drive powder sense swage sense primer orientation sense Lyman pro series dies Please Like and Subscribe lots more product content on the way Edited August 4, 2020 by TheStagePlan Link to comment Share on other sites More sharing options...
Furrly Posted August 4, 2020 Share Posted August 4, 2020 13 minutes ago, TheStagePlan said: Quick Update Last Friday I order a Mark7 Evolution from Shooters Connection, 5 days later it arrived in the west coast total setup time was about 3 hours. other then a molex cable that was pinned incorrectly on the primer sense the machine has been running flawlessly. Here is a quick video of it running around 800 rounds per hour. Mark 7 evo + auto drive powder sense swage sense primer orientation sense Lyman ori series dies Please Like and Subscribe lots more product content on the way What Lyman dies did you say they where??? Link to comment Share on other sites More sharing options...
TheStagePlan Posted August 4, 2020 Share Posted August 4, 2020 1 minute ago, Furrly said: What Lyman dies did you say they where??? those would be the typo version of the dies lol thanks. They are pro series dies Link to comment Share on other sites More sharing options...
Furrly Posted August 4, 2020 Share Posted August 4, 2020 1 minute ago, TheStagePlan said: those would be the typo version of the dies lol thanks. They are pro series dies I have been tossing the idea about that set, what are your thoughts on those dies??? Link to comment Share on other sites More sharing options...
TheStagePlan Posted August 4, 2020 Share Posted August 4, 2020 So far so good I am coming from a manual 1050 with Dillion dies so having the adjustability is amazing for me. I love having the micrometer's on the dies the machined texture provides excellent grip for adjustments plenty of space for a proper snap on box end wrench for tightening the lock rings setup instructions for the dies were clear with good detail for there adjustment settings they look even more impressive then the press itself Link to comment Share on other sites More sharing options...
TheStagePlan Posted August 6, 2020 Share Posted August 6, 2020 A Quick look at the Lyman pro series die set https://youtu.be/0u5-Pcxpe98 Link to comment Share on other sites More sharing options...
TheStagePlan Posted August 10, 2020 Share Posted August 10, 2020 (edited) Can anyone tell me the purpose of the 3D printed part and that sprung clamp for the cases feeder? I’m not sure it’s function is other then create clogs and jams I’m guessing I have is setup wrong. I’m guessing they are still working on the instructions manual I was attempting to load some shell shock cases with 50 percent of the cases coming down the feeder upside down I removed the 3D printed part when loading brass as it was constantly jamming and flipping off the case feeder. I tossed it back in for the shell shocks with the same results. I’m on My last bag of those cases. I now pick them up with a magnet and throw them straight in the trash. I would avoid using these cases with these dies after about 2 hours of loading I managed to load 150 rounds and it appear it chewed through a new Lyman pro series die Edited August 10, 2020 by TheStagePlan Link to comment Share on other sites More sharing options...
cool Posted August 10, 2020 Share Posted August 10, 2020 Hello no more jam problem since I adjusted this little aluminum part.and in 9mm the cases would turn over by tapping the plastic rim of the funnel, a simple piece of paper inside the funnel, no more cases being turned upside down in the feed tube.The funnel is too short for 9mm. Link to comment Share on other sites More sharing options...
TheStagePlan Posted August 10, 2020 Share Posted August 10, 2020 I adjusted the spring flipper and still in the case you are using the shell shocks cases they still tend to flip with the mouth facing down : ( I like the idea of your funnel extender I think I am going to have a 3d part designed to improve this here is a quick video of my experience Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now