FALAR Posted December 26, 2018 Share Posted December 26, 2018 So I picked up my new Stock II today. Immediately I noticed "man, this trigger is awful and gritty" then I went to drop the mag and it was gritty as well. I broke the gun down and there was metallic dust everywhere, and I mean everywhere. Some larger flakes as well. I spent about 30m with compressed air trying to get it all, but some seemed stuck (oil/grease will do that) so I did a thorough flush with WD 40 to push it all out. Some grit remains in the trigger and I suspect its because I can't really flush in between the trigger bar and the sides of the frame and there must still be metal dust in there. I only have one other Tanfoglio (a Stock III) and it most certainly did not arrive like this. I am not the type to want to tear down the frame to its base components (too much of a PITA for my limited patience) and found it odd to arrive with so much metal dust inside. I'm also going to check the barrel fitment because the rear most lug has the tiniest little sliver of wear already just from the test firing. Gun was made just last month. Link to comment Share on other sites More sharing options...
Craig0ry Posted December 26, 2018 Share Posted December 26, 2018 Honestly nothing surprises me with Tanfoglio, my trigger was very gritty until I took all the parts out and polished them to a mirror, I had to send my stock III back twice because the special edition nickel finish was terrible, the first gun I could scratch off with a fingernail, second gun looked the texture of leather and was really bumpy, and the third gun looked good and has been holding up great, they do take a lot elbow grease to get them where you want it seems. Link to comment Share on other sites More sharing options...
FALAR Posted December 26, 2018 Author Share Posted December 26, 2018 And here I was thinking "damn these guns are the best kept secrets $/quality" so I was kind of surprised. Not only that.........I don't see how much metal dust could have got in here to begin with. It's like every component was dipped in it. Link to comment Share on other sites More sharing options...
GringoBandito Posted December 26, 2018 Share Posted December 26, 2018 You may want to flush that WD 40 out of there as it will eventually gum up. Link to comment Share on other sites More sharing options...
Kixx Posted December 26, 2018 Share Posted December 26, 2018 21 minutes ago, FALAR said: And here I was thinking "damn these guns are the best kept secrets $/quality" so I was kind of surprised. My Stock 2 is a great gun, but the trigger was awful when I got it. I’m like you and expected at least a decent one like that on the Shadow 2. Nope. With a box of parts from Patriot Defense and a lot of time spent watching MemphisMechanic’s YouTube series, the gun is very nice now and the trigger is just how I like it. Link to comment Share on other sites More sharing options...
FALAR Posted December 26, 2018 Author Share Posted December 26, 2018 (edited) http://i64.tinypic.com/2il0l7p.jpg[/IMG] So I tried to get a pic of the last part I hadn't cleaned yet. I know it may look like "carbon" fouling but if you look on the lower half you should be able to see that it is metal shavings or metal dust of some sort. Almost like they MPI'd the entire gun and left the particles on it. Edited December 26, 2018 by FALAR Link to comment Share on other sites More sharing options...
Polymer Posted December 27, 2018 Share Posted December 27, 2018 That's awful. Not like it'll really help but did you call EAA to see what they will say. Link to comment Share on other sites More sharing options...
GrumpyOne Posted December 27, 2018 Share Posted December 27, 2018 3 hours ago, GringoBandito said: You may want to flush that WD 40 out of there as it will eventually gum up. Exactly. Use some spray brake cleaner in there, not WD40. Link to comment Share on other sites More sharing options...
FALAR Posted December 27, 2018 Author Share Posted December 27, 2018 1 hour ago, Polymer said: That's awful. Not like it'll really help but did you call EAA to see what they will say. No.....I mean, I know what the issue is. A bunch of metallic dust and shavings all over everything. From another thread if I sent it in to them and they detail stripped the frame it appears they may not even re-assemble it right. Cleaning what I could without detail stripping the frame didn't do the trick though. I can still feel grit in the trigger or when cocking the hammer. I think the frame is just going to have to be detail stripped. Link to comment Share on other sites More sharing options...
MemphisMechanic Posted December 27, 2018 Share Posted December 27, 2018 3 hours ago, Kixx said: ...parts from Patriot Defense and a lot of time spent watching MemphisMechanic’s YouTube series... Link to comment Share on other sites More sharing options...
MemphisMechanic Posted December 27, 2018 Share Posted December 27, 2018 21 minutes ago, FALAR said: Cleaning what I could without detail stripping the frame didn't do the trick though. I can still feel grit in the trigger or when cocking the hammer. I think the frame is just going to have to be detail stripped. The good lord is trying to tell you to do through polishing job on it by forcing you to take it apart. Link to comment Share on other sites More sharing options...
FALAR Posted December 27, 2018 Author Share Posted December 27, 2018 (edited) Haha......I'm not much of DIY'er. I have limited patience and tend to get frustrated and break things. Grips, hammers, hammer springs are about the extent of modifications I do on pistols. Small parts can really, really push my buttons. I just can't believe how much metallic dust and flakes were in this gun. I suspect the barrel fit too since the most breechward lug has a very small amount of wear already just from the test firing. I did the sharpie trick Johnbu recommended and of course, that spot with the wear was the shiniest and most free of the marker. I might just send it out for work and this will be the excuse. If it weren't for the debris I don't know if I would even describe the trigger as "bad". Like my stock III the SA even feels light. The uneven nature of the DA pull is what gets me (man is it bad compared to say, a Beretta with some good work done) but even then the overall pull weight isn't enormous. Edited December 27, 2018 by FALAR Link to comment Share on other sites More sharing options...
Polymer Posted December 27, 2018 Share Posted December 27, 2018 4 hours ago, FALAR said: Haha......I'm not much of DIY'er. Send it to Patriot Defense, problem solved! Link to comment Share on other sites More sharing options...
yigal Posted December 27, 2018 Share Posted December 27, 2018 sorry to hear this . but the all tanfo's they sent to my country was perfect. i checked the all batch. i don't know why they send to U.S guns in this condition. Link to comment Share on other sites More sharing options...
Catmanduex Posted December 27, 2018 Share Posted December 27, 2018 2 hours ago, yigal said: sorry to hear this . but the all tanfo's they sent to my country was perfect. i checked the all batch. i don't know why they send to U.S guns in this condition. Hillary’s emails. Link to comment Share on other sites More sharing options...
IHAVEGAS Posted December 27, 2018 Share Posted December 27, 2018 It would be interesting to try and find out what happened after the gun was assembled. It is hard to imagine someone assembling the gun with dirty parts. 10 hours ago, FALAR said: I have limited patience and tend to get frustrated and break things. Grips, hammers, hammer springs are about the extent of modifications I do on pistols. Small parts can really, really push my buttons. That is a choice not an affliction. Not ragging on you if you choose not to fix it, but it is rewarding and eventually people you know will start to think you are smarter than you are because you can fix things and know how to attack problems. I think the first rule is do not try to push through a job when you are mad at it, fix the mad at it part and then go back and look at what you are doing. Link to comment Share on other sites More sharing options...
FALAR Posted December 27, 2018 Author Share Posted December 27, 2018 7 hours ago, yigal said: sorry to hear this . but the all tanfo's they sent to my country was perfect. i checked the all batch. i don't know why they send to U.S guns in this condition. I've seen issues posted online of other guns with issues out of the box. I had to send a Beretta back recently that came with an un-staked extractor pin. But......metallic dust and flakes all inside the gun is a headscratching "WTF" from me. I don't even know how that happens. Link to comment Share on other sites More sharing options...
chaserracer Posted December 27, 2018 Share Posted December 27, 2018 Hate to say this, but If you are not somewhat of a DIY'er and small little parts frustrate you, my dude you may have purchased the wrong gun in the Tanfoglio Stock 2. These babies are a labor of love and for the sake of tuning and reliability will require you to strip them down to bare frame, often. Good news is, someone on here has already been through and fixed what you are now and eventually will be experiencing - We are here to help! The trick is to learn the process early, once you realize how few parts and steps there really are it simply becomes a non-issue and you are free to tinker as you please to get it to run how you want it to. But...If that all sounds like hell to you - you can always sell it - in most cases, for a profit! Link to comment Share on other sites More sharing options...
johnbu Posted December 27, 2018 Share Posted December 27, 2018 Looks like someone dropped it in the dust bin. I'd try this.... Take off the grips. Remove the slide. Take the frame part outside and really hose it out with a full can of non-chlorinated brake cleaner. Use the little straw and get in every nook and cranny. Move the hammer, trigger, etc. Really get the parts under the sear cage and in the hammer spring area. Then lube it good. I use 5w30 on most parts, grease ob the rails. Watch those videos a few times. When you get your courage up, give it a whirl. The "frustrating" areas are the sear pack if it has a 2 piece sear and the trigger bar lifter. sadly, polishing that lifter is one of the most important areas for a smooth trigger. No worries if you get stuck. Just drop a line here and plenty will assist. Link to comment Share on other sites More sharing options...
IHAVEGAS Posted December 27, 2018 Share Posted December 27, 2018 3 hours ago, chaserracer said: strip them down to bare frame, often. Still haven't done this with my match gun since putting in all the PD goodies, not a ridiculous number of rounds on it but probably 20,000 ish and most of that with titegroup which is thought to be dirty. Really, after you get through what can be considerable new gun pains I am not seeing a reason for anything special regarding maintenance except that I need to clean around the extractor area about every 5000 rounds. Have switched to power pistol powder so I am curious to see if the extractor area will still get gummed up. Hammer springs weaken over time and I have had to install a couple of them. Link to comment Share on other sites More sharing options...
dhdeal Posted December 29, 2018 Share Posted December 29, 2018 On 12/27/2018 at 6:01 PM, IHAVEGAS said: and most of that with titegroup which is thought to be dirty. Ha! But it is dirty! Dirty, hot, and accurate that is. I've started to use Sport Pistol, and while relatively clean, is no more accurate than Titegroup in my 9's. I haven't taken my Limited apart yet (beyond field striping) but as I'm more than comfortable taking a 2011 down to the smallest part, I'll manage. I understand the aggravation of the OP in finding a new toy in the shape described. I'd be tempted to stick it in my ultrasonic cleaner. Link to comment Share on other sites More sharing options...
IHAVEGAS Posted December 29, 2018 Share Posted December 29, 2018 5 hours ago, dhdeal said: I haven't taken my Limited apart yet (beyond field striping) but as I'm more than comfortable taking a 2011 down to the smallest part, I'll manage. With Tanfo's and CZ's you learn about using slave pins for the sear cage and installing the trigger. Lots of good how to info out there, I agree, you will manage. Link to comment Share on other sites More sharing options...
Trinimon Posted December 30, 2018 Share Posted December 30, 2018 (edited) Like the OP, this was my first personal awakening too into Tanfoglios. The ones I tried from other shooters on the range felt nice. I eventually saved up my milk money and bought a Limited Custom expecting it to be awesome out of the box. Holy crud, that had to be one of THE grittiest triggers out of all the guns I owned. About 5hrs of polishing and a few hundred $$ later in Xtreme parts, it's where I imagined what it should have been for a $2K pistol. My Shadow 2 was way better out of the box and with a shorter reset. Sometimes I wished I had waited for a CZ Orange in 40SW to come into stock. Edited December 30, 2018 by Trinimon Link to comment Share on other sites More sharing options...
FALAR Posted December 31, 2018 Author Share Posted December 31, 2018 If the trigger was just a little gritty and rough, that'd be one thing. But the metal dust and shavings to me were alarming because of the damage they can cause. Hence why I still haven't fired the gun out of fear of what may be down in the frame's recesses. Link to comment Share on other sites More sharing options...
Dr Mitch Posted December 31, 2018 Share Posted December 31, 2018 This thread should be called “Why to buy a Shadow 2”. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now