nipplehead Posted February 24, 2009 Share Posted February 24, 2009 Hey guys looking to mount a tactical sling on a JP rifle with the Ace Skelitized stock . I would like a quick disconnect swiveling setup. Does anyone make something that will connect to the existing mounts on the hand guard/? I did not find anything on the JP site other than the Viking sling...no mounts What would be the best way to go? Link to comment Share on other sites More sharing options...
DMAC Posted February 25, 2009 Share Posted February 25, 2009 Hey guys looking to mount a tactical sling on a JP rifle with the Ace Skelitized stock . I would like a quick disconnect swiveling setup. Does anyone make something that will connect to the existing mounts on the hand guard/? I did not find anything on the JP site other than the Viking sling...no mountsWhat would be the best way to go? Mount a section of rail on the handguard and then attach one of these. I'm not sure how to mount the other end to the Ace stock though. Link to comment Share on other sites More sharing options...
davidwiz Posted February 25, 2009 Share Posted February 25, 2009 Magpul makes what looks like a pretty nice sling and mount. Link to comment Share on other sites More sharing options...
cas Posted February 25, 2009 Share Posted February 25, 2009 I went through this last week.... and didn't come up with an answer. I wanted to get Push Button QD's for my rifle, but didn't come up with a way of attaching one to the ACE stock. The FF end is easy, lots of choices. The stock end I didn't come up with an answer, so I just put the older style QD studs on it. Link to comment Share on other sites More sharing options...
Smithars Posted February 25, 2009 Share Posted February 25, 2009 Hey guys looking to mount a tactical sling on a JP rifle with the Ace Skelitized stock . I would like a quick disconnect swiveling setup. Does anyone make something that will connect to the existing mounts on the hand guard/? I did not find anything on the JP site other than the Viking sling...no mountsWhat would be the best way to go? Mount a section of rail on the handguard and then attach one of these. I'm not sure how to mount the other end to the Ace stock though. I wonder if something like this would work for putting it on the stock. It looks like it attaches to the extension tube in that picture so I'm not sure if it would fit on the top bar of the Ace stock. Here's a couple others that seem to be about the same thing; here and here I thought I remember seeing one that replaced the receiver end plate but can't find it. Link to comment Share on other sites More sharing options...
stik Posted February 25, 2009 Share Posted February 25, 2009 Here is a QD that I use on my ACE stock http://riflestocks.com/catalog/product_inf...products_id=308 You can get a JP rail section for the FF tube and get a DD or Larue QD that attaches to the rail. Link to comment Share on other sites More sharing options...
jbullgpd Posted February 26, 2009 Share Posted February 26, 2009 I have the midwest industries buffer tube QD on my rifle and like it alot, I recommend it..... Link to comment Share on other sites More sharing options...
Stuck in C Posted February 26, 2009 Share Posted February 26, 2009 I drilled and tapped a hole in the butt of my Ace Skeleton stock and installed and locktited one of the swivel attachments that came with the stock there, instead of at the front of the stock where it came drilled from the factory. There seems to be plenty of material there to hold it. I then attached an Uncle Mikes QD swivel. I also have an attachment that came with one of my Tacticool slings that consists of a double loop of parachute cord threaded through a nylon sling fitting (swivel). You remove the rubber recoil pad from the stock, loop the cord around the aluminum piece, and then reattach the recoil pad. Works slick. Someone must make one of these you can buy without the sling. Link to comment Share on other sites More sharing options...
jobob Posted February 26, 2009 Share Posted February 26, 2009 I've also been trying to figure a way to mount a push button QD on a rifle A1 stock. Anyone have an idea on that one? Link to comment Share on other sites More sharing options...
jobob Posted February 26, 2009 Share Posted February 26, 2009 Oops! Should have looked a little farther on the Ace site. Here's one in case anyone needs it too. http://riflestocks.com/catalog/product_inf...products_id=325 Link to comment Share on other sites More sharing options...
uscbigdawg Posted February 27, 2009 Share Posted February 27, 2009 VTAC on regular sling swivels. All I ever needed. Rich Link to comment Share on other sites More sharing options...
Deerhunter9790 Posted February 9, 2015 Share Posted February 9, 2015 Now that it has been a coupe of years, anyone have any new ides for this? Link to comment Share on other sites More sharing options...
Mberry Posted February 9, 2015 Share Posted February 9, 2015 Absolutely! My friend Kasey Beltz of B&T industries created a method to attach his monopod on the ACE stock. He added QD sling attachments to fix the sling mounting solution too. Great product all around and it solves the problem beautifully. http://www.accu-shot.com/images/BT51-install-lg.jpg http://www.accu-shot.com/catalog/product_info.php?cPath=23&products_id=131 Link to comment Share on other sites More sharing options...
CyclicRate Posted February 9, 2015 Share Posted February 9, 2015 Once you get the stock figured out, I highly suggest the Blue Force Gear slings. I really like their 2-2-1 sling if you have a QD mount near where the buttstock meets the receiver. If you're strictly looking for a two point, they have the best adjustable option for that too. Both the two point and 2-2-1 allow you to use the quick adjust tab feature as a loop sling for support in different shooting positions. Link to comment Share on other sites More sharing options...
Ming the Merciless Posted February 9, 2015 Share Posted February 9, 2015 I didn't like the sling located to the top or bottom of the Ace Skeleton stock, so I just drilled and tapped 10-32 holes in the side of the aluminum butt portion to match a Samson (?) two screw keymod QD mount. This looks like the one I used, but no guarantee since it was laying in a box of unused parts under my bench. http://www.midwayusa.com/product/922501/samson-quick-detach-swivel-sling-mount-for-evolution-series-free-float-handguard-ar-15-aluminum-black?cm_vc=ProductFinding Link to comment Share on other sites More sharing options...
Shooter115 Posted February 9, 2015 Share Posted February 9, 2015 The JP hand guard should have come with 2 of the traditional QD sling studs (at least mine did). If you want the sockets you can use the JP backer plate with one of Nordics QD sockets. https://nordiccomp.com/product/qda-for-nordic-components-hand-guards/ Link to comment Share on other sites More sharing options...
larry weeks Posted February 9, 2015 Share Posted February 9, 2015 Ace is threaded 10-32 on the front block. Get Uncle Mikes 593-101-100 from Brownells. Or, if you have the swivels, Brownells sells a bulk pack of the sockets only. Spend a bit of time in the fasteners aisle of the hardware store and find a 1/2" or 3/4" long screw. I had some in my part bins so flattened the head and tapered the underside to match the inside shape of the socket. Ground a bit off the swivel too. A little messing around and it works out fine. Clean and simple with no extra mounts hanging off the gun. Link to comment Share on other sites More sharing options...
Deerhunter9790 Posted February 10, 2015 Share Posted February 10, 2015 Thanks for all the quick responses! Ill check the links out. As far as the blue force gear slings go, I used one in afghanistan and still use it. Great sling! Link to comment Share on other sites More sharing options...
Deerhunter9790 Posted February 10, 2015 Share Posted February 10, 2015 Absolutely! My friend Kasey Beltz of B&T industries created a method to attach his monopod on the ACE stock. He added QD sling attachments to fix the sling mounting solution too. Great product all around and it solves the problem beautifully. http://www.accu-shot.com/images/BT51-install-lg.jpg http://www.accu-shot.com/catalog/product_info.php?cPath=23&products_id=131 Thats pretty bad ass! Link to comment Share on other sites More sharing options...
DocHolliday1 Posted February 10, 2015 Share Posted February 10, 2015 This may be the same as one of the above that didn't work since it was a few years old. I'm thinking of getting one for my Ace http://riflestocks.com/store/product46.html Link to comment Share on other sites More sharing options...
JGC Posted February 16, 2015 Share Posted February 16, 2015 JP Enterprises makes a QD socket specifically to attach to their modular handguards. I bought one from them right when they came out a few years ago. It's part number JPHG-SM on this page: http://jprifles.com/1.5.1.1_slings.php Outstanding quality as with everything else out of JP. Link to comment Share on other sites More sharing options...
outerlimits Posted February 27, 2015 Share Posted February 27, 2015 i don't want anything hanging on the stock to catch stuff when mounting the gun. i like the AP custom QD mount for the handguard, so i bought another. remove the rubber butt pad, drilled and tapped the rear of the stock. red loctite so it ain't going anywhere. mounted on the inside of the stock it's hidden until you need it. easy and very slick way to deal with it. Link to comment Share on other sites More sharing options...
ShooterSteve Posted February 28, 2015 Share Posted February 28, 2015 I don't like single point slings, but Stark grips come with a single point QD at the top of their grip. Maybe work it into your system with a front mount to use a regular sling. I really like Stark grips. I have them on several of my ARs. Link to comment Share on other sites More sharing options...
ropsitos Posted March 1, 2015 Share Posted March 1, 2015 I use a vtac sling as purchased from laRue. I connect it to the Jp qd on the hand guard and for the stock connection i use an hk hook which I clip to the upper strap loop that comes with the stock. Link to comment Share on other sites More sharing options...
Deerhunter9790 Posted March 6, 2015 Share Posted March 6, 2015 i don't want anything hanging on the stock to catch stuff when mounting the gun. i like the AP custom QD mount for the handguard, so i bought another. remove the rubber butt pad, drilled and tapped the rear of the stock. red loctite so it ain't going anywhere. mounted on the inside of the stock it's hidden until you need it. easy and very slick way to deal with it. Do you have any problem with the qd mount rotating since it it only has one screw? Mounting a qd mount in this location makes the most sense to me Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now