wannabe Posted September 9, 2013 Share Posted September 9, 2013 I was wondering what bullet weight and velocity is giving the best results with the Vortex 1x6 JM reticle. Link to comment Share on other sites More sharing options...
KungPfoo Posted September 9, 2013 Share Posted September 9, 2013 I'm interested in this scope, but wrestling with the BDC reticle - would prefer a straight MOA type "ladder". Manual says "...0-3 inch of your aiming point..." with a 200yd zero and 55-77gr bullet traveling at 2700-3000 fps. Here's the way the reticle lines up for my rifle (18" Noveske) and several bullet types (my actual chrono data and using JBM ballistics calculator): Green is good-to-go. Yellow is within .5in of the "3 in" range. Red means the hash mark is missing the intented range (3,4,5,600 yds) by the number indicated in parens. So, in my case the 75gr Hornady Match with a 200yd zero is the best fit. I don't have the scope so none of this is range verified. I had expected more rounds to be within the 0-3in range of the hash marks. From here http://www.brianenos.com/forums/index.php?showtopic=157295&page=6 So it looks like the Hornady Match 75 Gr at 2760 with a 200 yd zero. Link to comment Share on other sites More sharing options...
outerlimits Posted September 9, 2013 Share Posted September 9, 2013 Doesn't matter. Just play around with velocities till you get the hash marks to match out to 400 and be done. Link to comment Share on other sites More sharing options...
JamesY Posted September 9, 2013 Share Posted September 9, 2013 Those hash marks line up when the scope is at 6x, correct? What about when it's at 3x, 4x, or 5x? How do you compensate for that? Or do most people only use 1x and 6x? Link to comment Share on other sites More sharing options...
outerlimits Posted September 9, 2013 Share Posted September 9, 2013 you will likely never use hashmarks other than at 6x. any less magnification, and the 200 yd dot works just fine. Link to comment Share on other sites More sharing options...
EaZeNuTZ33 Posted September 9, 2013 Share Posted September 9, 2013 I use 69gr SMK handloads at right over 2700fps. The lines do not line up "perfectly" with the expected 300, 400,....yard increments, but are damned close according to todays weather conditions via iStrelok. Mine line up at 200 yd zero, 300yds for the first line, 393yds for the second line, and 487yds for the third line. Close enough for 4moa targets IMO. Link to comment Share on other sites More sharing options...
mpeltier Posted September 10, 2013 Share Posted September 10, 2013 Instead if matching the load to the reticle, why not develop the best load for your rifle and match the BDC stadia to it? Takes some work at the range, but not much more than verifieng stadia distances. Then make a BDC range card that might look something like this: 200=zero First line=299 2nd=388 3rd=490 4th=502 This is just as relevant as 300,400,500 etc scince the targets are never at those exact distances anyway. Knowing what the stadia represents in relation to your target is what's important. Does this make sense? Link to comment Share on other sites More sharing options...
Steve RA Posted September 10, 2013 Share Posted September 10, 2013 Yes. Link to comment Share on other sites More sharing options...
venatic Posted September 10, 2013 Share Posted September 10, 2013 Instead if matching the load to the reticle, why not develop the best load for your rifle and match the BDC stadia to it? Takes some work at the range, but not much more than verifieng stadia distances. Then make a BDC range card that might look something like this: 200=zero First line=299 2nd=388 3rd=490 4th=502 This is just as relevant as 300,400,500 etc scince the targets are never at those exact distances anyway. Knowing what the stadia represents in relation to your target is what's important. Does this make sense? Yes except the 4th would be closer to 602 Link to comment Share on other sites More sharing options...
mpeltier Posted September 10, 2013 Share Posted September 10, 2013 Yeah, I was just throwing random numbers as an example. Everyone's range card potentially would be a little different. Link to comment Share on other sites More sharing options...
Alaskapopo Posted September 11, 2013 Share Posted September 11, 2013 Those hash marks line up when the scope is at 6x, correct? What about when it's at 3x, 4x, or 5x? How do you compensate for that? Or do most people only use 1x and 6x? LIke Outerlimits said you generally only use the BDC on max power. However I do use the scope on all power ranges not just 1 and 6. You are severaly limiting yourself if you do that. Look at the target arrary on the make ready command and then adjust your magnification to give you enough field of view to see the target on either side of the one you are shooting at and enough magnification to clearly see your target. Pat Link to comment Share on other sites More sharing options...
JPeel Posted September 11, 2013 Share Posted September 11, 2013 Instead if matching the load to the reticle, why not develop the best load for your rifle and match the BDC stadia to it? Takes some work at the range, but not much more than verifieng stadia distances. Then make a BDC range card that might look something like this: 200=zero First line=299 2nd=388 3rd=490 4th=502 This is just as relevant as 300,400,500 etc scince the targets are never at those exact distances anyway. Knowing what the stadia represents in relation to your target is what's important. Does this make sense? I shoot three long distance loads depending on the target array and wind. I have the strelok reticle diagram printed out for each load, laminated and keep that in my range bag. Once I know the target distances I can refer to the diagram and know my holds from the diagram. The visual of the diagram is quicker and easier for me to use than a chart. If the wind is high on match day then I can run strelok on the ipad or phone and have a current reticle diagram for those conditions. The strelok also allows you to change the magnification power and the reticle changes with it. So if you want to know where the stadia lines are at lower powers now you can. Link to comment Share on other sites More sharing options...
mpeltier Posted September 11, 2013 Share Posted September 11, 2013 Instead if matching the load to the reticle, why not develop the best load for your rifle and match the BDC stadia to it? Takes some work at the range, but not much more than verifieng stadia distances. Then make a BDC range card that might look something like this: 200=zero First line=299 2nd=388 3rd=490 4th=502 This is just as relevant as 300,400,500 etc scince the targets are never at those exact distances anyway. Knowing what the stadia represents in relation to your target is what's important. Does this make sense? I shoot three long distance loads depending on the target array and wind. I have the strelok reticle diagram printed out for each load, laminated and keep that in my range bag. Once I know the target distances I can refer to the diagram and know my holds from the diagram. The visual of the diagram is quicker and easier for me to use than a chart. If the wind is high on match day then I can run strelok on the ipad or phone and have a current reticle diagram for those conditions. The strelok also allows you to change the magnification power and the reticle changes with it. So if you want to know where the stadia lines are at lower powers now you can. That ap programs pretty cool and would certainly save time at the range. I was impressed with how many reticles it supported. Thanks for sharing that. Link to comment Share on other sites More sharing options...
Doug H. Posted September 11, 2013 Share Posted September 11, 2013 I'd say read the manual and follow the directions. http://www.vortexoptics.com/uploads/web_man_rfl_razor-hd_jm-1.pdf Doug Link to comment Share on other sites More sharing options...
Stlhead Posted September 11, 2013 Share Posted September 11, 2013 Doug, you keep your logic filled mouth shut. The thought of someone varying their load in order to get the ballistics to match the reticle in their scope fills my heart with great joy. Link to comment Share on other sites More sharing options...
P.E. Kelley Posted September 11, 2013 Share Posted September 11, 2013 I never worked THAT hard running Irons. Damn, them scopes make shooting tough. Link to comment Share on other sites More sharing options...
Doug H. Posted September 11, 2013 Share Posted September 11, 2013 I'll admit to changing my zero on my Swarovski 1-6 BRT to get the lines to match my drops but that reticle is in mils which seems easier to me. Doug Link to comment Share on other sites More sharing options...
openclassterror Posted September 12, 2013 Share Posted September 12, 2013 You can also vary the power to match your trajectory, as long as it has more arch than the ideal zero. That is how the Nikon BDC system is DESIGNED to work, and you can apply the technique to any second focal plane reticle. Once you find the zoom that puts the lines in the right place (maybe it's 5-1/4 or whatever) you can just return to that power to use the stadia lines. In the real world though, it doesn't matter whether it correlates with exact yardages since targets are hardly ever at even distances. As long as you know that line 3 is 420 yards instead of 400 (or wherever it ends up), you hold a little high for 453 and a little low for 408. All the distances are adjustments, really. Tom Link to comment Share on other sites More sharing options...
Vespid_Wasp Posted September 13, 2013 Share Posted September 13, 2013 Why not just alter your zero slightly and 'shift the curve' as it were to match more closely? Instead of zeroing at 200 with the crosshairs, zero at 400 with the 400 stadia line. It might alter your 200 yard zero an inch or two but we aren't shooting at gnats. If a ballistics calculator matches real world performance, zeroing 1.1 inches high at 200 (essentially a 220 yard zero) gives me almost perfect calibration with my 75gr load. I tune my load for accuracy and velocity and it's quite simple to alter your zero for an acceptable curve to match the BDC. Link to comment Share on other sites More sharing options...
GM2B Posted September 13, 2013 Share Posted September 13, 2013 I use the 77SMKs and it works great! I push them around 2600 FPS and I run 1 inch high at 200 yards but about spot on the rest of the way. It ends up a little low at 500 Yards but it has never bothered me in a match. You can push the bullet faster to better line up but as others have stated tune the load to the barrel and adjust the zero accordingly. Link to comment Share on other sites More sharing options...
mpeltier Posted September 13, 2013 Share Posted September 13, 2013 Why not just alter your zero slightly and 'shift the curve' as it were to match more closely? Instead of zeroing at 200 with the crosshairs, zero at 400 with the 400 stadia line. It might alter your 200 yard zero an inch or two but we aren't shooting at gnats. If a ballistics calculator matches real world performance, zeroing 1.1 inches high at 200 (essentially a 220 yard zero) gives me almost perfect calibration with my 75gr load. I tune my load for accuracy and velocity and it's quite simple to alter your zero for an acceptable curve to match the BDC. This is a good idea also. For kicks I ran the tables for the load the vortex reticle is calibrated then ran my pet loads in 75 and 55 gr loads respectively. My 75 was only 4" off (higher) than the baseline and 1-2 inches off at the other distances. My 55 was quite a bit farther off but changing my zero to 210 yds put me right on the money and was off by 1" at all but 600 witch was off by 2". Close enough. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now