JamesY

FEBRUARY Feb 22-23 CowTown MultiGun ExCommunicado - Phoenix, Arizona. MARCH March 20-22 Superstition Mountain Mystery 3-Gun - Rio Salado Sportsman's Club, Mesa, AZ APRIL MAY May 1-3 -Texas 3 Gun Championship - Reveille Press Ranch - Burnet, TX May 14-16 Blue Ridge Mountain 3-Gun Championship - The Clinton House Plantation - Clinton, SC REGISTRATION HERE May 16-17 He-Man 3-Gun Nationals - NRA Whittington Center. May 30-31 Johnson 3-Gun 2-Rifle Match - NRA Whittington Center Coal Canyon May 30-31 Aero Precision NW Multi-Gun Challenge - COSSA Range - Bend, OR JUNE JULY AUGUST August 15-16 Johnson 3-Gun RM3G - NRA Whittington Center. SEPTEMBER September 5&6 - 2020 Pennsylvania State 3-Gun Championships - New Tripoli, PA Ontelaunee Rod & Gun Club (2020 UML Rule set) OCTOBER NOVEMBER

FEBRUARY CowTown MultiGun ExCommunicado - Phoenix, Arizona Feb 22nd & 23rd, 2020 REGISTRATION PAGE MARCH Superstition Mountain Mystery 3-Gun - Rio Salado Sportsman's Club, Mesa, AZ March 20-22, 2020 REGISTRATION PAGE APRIL MAY He-Man 3-Gun Nationals - NRA Whittington Center May 16-17, 2020. REGISTRATION PAGE Johnson 3-Gun 2-Rifle Match - NRA Whittington Center Coal Canyon May 30-31, 2020. REGISTRATION PAGE JUNE JULY AUGUST Johnson 3-Gun RM3G - NRA Whittington Center August 15-16, 2020. REGISTRATION PAGE SEPTEMBER OCTOBER NOVEMBER

I got less than 1k rounds out of my firing pin in my CMMG PCC. This happened during a stage at Ironman a couple years ago. Had to run to my bag to get a backup pistol to finish the stage. Luckily, I had a backup firing pin.

With a FFP scope I can see that working but with SFP, does it work the same in terms of POI/POA?

I'd go with a Nordic 18" barrel in 223 wylde. I have two and love them. Low recoil, even with a standard block. Also, I've always put my own uppers together with no problems using the DPMS action block. I usually torque on the lower end close to 35 ft/lbs or whenever the nut lines up with the gas tube. I haven't had accuracy nor reliability issues in 6+ rifles so I must be doing something right.

AP Custom Rhino

I used a 16" in 2013 then switched it up to 18" in 2014. Now I'm back to a 16" using a Nordic barrel. There's slightly more felt recoil but I can swing it faster since most of the matches I shoot rarely go further than 180 yds.

http://www.joeboboutfitters.com/Burris_MTAC_1_4X24MM_Illuminated_Reticle_5_56_CQ_2_p/bur300214.htm

Nice! I'll have to try this on one of my ARs. Thanks for the tutorial.

^^ pack two shotguns. One for shot, one for slugs. You'll save a little time from reloading. If one breaks, at least you have another.

I have a CMMG 9mm carbine with a geissele SD3G and it runs great. I used it the last two years at MGM Ironman and other than too much lube or a broken firing pin, it had no problems. With 125gr MG JHP, i can do 6" groups at 100 yards. With 147s, it's all over the place. I also had to add weight to the buffer tube as well as add coins to tune it. Other than that, no other tuning was required.

I have a QC10 lower with a Gibbs side charging upper. Runs flawlessly. If I shoot trooper this year, I'll run it. I used a CMMG setup the last two years using a VM Hytec block and UZI mags. It ran great also! I had a Geissele SD3G trigger and cheap Bushnell 1x on it. I was quad tapping spinners and spinning them quickly. The most fun I've ever had at ANY match was when shooting my PCC at pistol targets. I recommend shooting trooper at least once. It's a blast! I might be shooting limited this year to take a little break from the 150lb load out

Still talking about followers here?

Stages look great... So does squad 1 start at stage 1, squad 2 start at stage 2, ...etc. ?

Got through to them but didn't get very far. I emailed the pics I posted above. We'll see what happens.

I tried that already. Unless I widen the holes, it's still not aligned. I've loaded about 15k rounds and this is the first time I'm having issues. I'm currently on hold with dillon. #10 in line...

I was hoping someone had this issue before and it was an easy fix. I guess I'll call Dillon tomorrow. Thanks

Hello, all. I noticed an issue last night with my primer seater. It's misaligned by a good amount (see below how it hugs the right). I tried many things like replacing/adjusting the index ball & spring, index pawl and indexer block and can't seem to fix it. Is there something I'm missing? I'm usually good at finding the problem but this has me stumped. I have a couple of big matches coming up and don't have ammo for them. I'd hate to send it back and not be able to load.

Mine never came loose after 3 seasons. I tightened the hell out of it and used blue loctite.

The Burris AR-1X Prism for $299 looks good for the price. I'm going to pick one up for a backup to my Prismatic. If it's really good, I'll make it my main limited optic. I was hoping to see a 1-4,5,6... FFP optic similar to USO's SR8C. Oh well, I guess I'll have to keep using my Tac 30 for now.

That's what mine looks like. you'll be fine.

Close-ups would have been nice.

I run 75 gr Hornady and 77 SMK through mine and they work fine. I can get 1" groups with my Tac30 at 100 yds. I'm sure if I had a cross hair reticle and more magnification, it would be better.

That 1-5 sounds interesting. If the Meopta has a better reticle, and is FFP, I'd be all over it.

Anyone heard of new scopes coming out?