Aircooled6racer

Hello: The new Aftec extractors are not the same as the old ones. I have some that are 10 years old or older and they look different than the new ones. I have also seen some of the new ones break and the spring retainer break as well. I have been using EGW and Ed Brown extractors in my last builds. They all need to be fitted and tuned, even the Aftec. Thanks, Eric

Hello: with the solar panel on the top of the Holosuns and a battery life of over 50,000 hours I don't think a battery change will be a worry for a very long time. Thanks, Eric

Hello: I have found I have not needed the extended magazine release. The original one works well for me. Thanks, Eric

Hello: There is no problem going straight to open but I would say you have to reload to shoot open major unless the cost of buying ammo is not a problem. Carry Optics will get you almost there at 1/4 the cost. Thanks, Eric

Hello: I would start with shooting Limited minor with the setup you have now. You will have to worry about only 1 reload and can just concentrate on the shooting. After 6 months or so I would then consider Carry Optics and getting into reloading. After another year I would then look back at what you enjoy shooting the most. It may surprise you what you like the best. Hope this helps. Thanks, Eric

Hello: Looks like the bottom of the slide could use a radius and the extractor could have a lead put on it to help the round get under it. Thanks, Eric

Hello: Someone here in Georgia bought a new one for $875 out the door. Thanks, Eric

Hello: I just found this today and I have not read all of it yet(just 4 posts so far). How much overhang does the barrel have into the magazine tunnel? Thanks, Eric

Hello: I would use the plate if it has locating pins and is tight in the cutout in the slide. The plate will only raise the dot up a little and is not a big deal as some of those out there think it is. I would rather have a secure mounting of the red dot that trusting two small screws to hold it in place. Thanks, Eric

Hello: take the shroud off the 510C and it is lighter than a aluminum C-More. The 507C is lighter but the window is half the size. I find I shoot both about the same but I need more time behind the 507C. I can see more through the glass on the 510C but I also see out side the glass on the 507C. Not sure if that makes sense unless you can compare both by looking at the same targets and shooting them. I shoot with both eyes open so that helps. Thanks, Eric

Hello: I have a 510C on one of my open pistols and just added a 507C to another one to try. I don't have too many rounds on the 507C setup yet but I like it as well. I have the 507C on my carry optics and it works great. Thanks, Eric

Hello: The Honcho uses weight of the slide and overall weight to tame some of the recoil also. If you like your pistols on the heavy side the Honcho may work for you. I am more of a fan of one pistol for one division. So if you are going to shoot Limited buy a limited pistol or for Open buy an Open pistol. That way as you grow as a shooter your likes and dislikes may change. Thanks, Eric

Hello: Shooters Connection sells the Blade Tech Hanger. They also have many other goodies that you will want as well. Christmas is coming. Thanks, Eric

Hello: Use UPS not a UPS Store. It should cost about $30 to ship from the UPS hub. Again not the UPS Store. Thanks, Eric

Hello: You could look at the Sig Max in 9mm. I had the 45 but it did not fit my large hands and I didn't want to start cutting on the frame. The Springfield Loaded in 9mm is pretty nice if you can find one. The old STI Spartans are pretty nice for the money as well as the Trojans. If you don't reload I would get a 9mm and some Dawson magazines. Any of the name brand pistol companies make good 9mm 1911's from what I have seen. The Springfields fit my large hands better than most of the others. Thanks, Eric

Hello: I am using the Taylor Freelance extensions and also the Taccom splice. I use the splice with either a 30-30 or a 20-30. All work well. Thanks, Eric

Hello: I would check your link and slide stop to see if there is much wear on them. The links will get the holes wearing in an oval shape and will not lockup as they once did. I am not a fan of the Accurails since once it is done you can't fit another slide to the frame without having it Accurailed also. The rails are a spring type tension and when you add a little dirt they tend to tighten up. Good for bullseye type shooting where there is not much dust thrown up by you running around. I have one 9mm open pistol with over 60,000 rounds and it is still accurate with a loose frame to slide fit. It locks up the same every time. Lastly check your barrel for wear usually on the top about 1" in. Thanks, Eric

Hello: Since we are less than 20% of the buyers of pistols I would think they will not be getting rid of the LCI barrel at all. Also remember the average person only shoots 50 rounds then goes home to clean the pistol. Thanks, Eric

Hello: Nothing wrong with Tite Group. It is a little snappy but it does work. Leave the weight out and try some 124's. You could also try shortening the stroke with some quarters to see if you like that. Thanks, Eric

Hello: I have tried most of the open holsters out there over the years. I am currently using a Safariland 014 which I like. I like having the muzzle support since it stops the pistol from flopping around if you miss your draw a little. The lock is not the easiest to set and the tension device is alright. I also like the hip pad since it make the holster sit in a good place for me when sitting or standing. Some of the other holsters I have tried have more adjustments than you would need and can come loose if you don't LocTite the screws. I would suggest you look at all your options in person before you buy. I am actually thinking of making a Kydex holster for my open pistol so I can use it for all the gun games. Thanks, Eric

Hello: I clean the mag and never have had a magazine problem. I have seen lots of guys that have had mag problems though. I have never worn out a follower since the magazine is kept clean. Your results may very. Thanks, Eric

Hello: All of my 21 round mags with TTI base pads fit the gauge. One real advantage with the TTI base pads is that they come off easily with no tools. If my mag hits the ground I clean it. You never know what can get inside the mag when it hits the dirt. Thanks, Eric

Hello: One thing to check also is the overall length of the case. I know if I try to use S&B 9mm brass in my open pistol I have problems with bulged cases and sometime extraction problems since the brass is shorter than other brass. I am not sure what recoil springs you guys are using since using one that is a little too light will cause problems also. Thanks, Eric

Hello: I am hoping that the 507C will hold up better than some of the other micro red dots. It also has a super long battery life and a solar panel. I have never had a problem with the C-More slide rides myself but I have seen quite a few of the micro red dots crap the bed at the wrong time. For me it also gives me the same sight picture as my Carry optics pistol. I will sight it in tomorrow and hopefully shoot a match on Thursday night to see how I like it. The Holosun on this mount moves the dot closer to your eye which may help also. Thanks, Eric

Hello: Well, I am going to test out a Holosun 507C on my open 9mm major pistol. I am hoping it will last so I can use the same scope for Open, Carry Optics and even PCC or rimfire. I really like the 507C on my Carry Optics Sig P320 X5. Still getting used to the small dot but it works even in bright sunlight. Thanks, Eric