lcambre

Not working: Error (410) Something went wrong. Don't worry, your files are still safe and the Dropbox team has been notified. Check out our Status Page to see if there is a known incident, our Help Center and forums for help, or head back to home.

Any word on what happened to further production of THRiL MPX magazines? I have not seen any since their initial release. The website shows out of stock and lists them as GEN 1. Are they doing a redesign? https://shop.thril.com/pmx-sm9-magazine/

SteelTargetPaint is a good one.

A few thoughts on the equipment rules. For Factory rifle optics, just 1x would be good if matches were set up so target size and visibility supported it. The option of a single fixed power would be good for people like me who have an old 3.5x TA11 on one of their guns. The 3x option would be my last pick due to having to buy a new optic to best fit the rules. The 1"x3" rule for breaks has a long history at this point. I agree that it is best to continue its use for factory division. For limited optics, I like the choice of limited or CO guns.

This guys channel has APC 9 footage: https://www.youtube.com/watch?v=S4jdhvWB77o

I received an in stock email from Eurooptic a couple days ago. It was in stock when I looked but is now out of stock.

I really wish people would stop saying legal 16". This gives the false impression that under 16"s is illegal. The correct term would be 'makes it a non NFA 16" rifle barrel in the USA.'

Today was the first day recently that I didn't need to sign in. Using Firefox on a Mac.

I probably could. Since I have two that work, I won't bother.

I was trying them with the gauge. It is just a tiny amount. I am looking now at one of them and one side of the magazine is fine it is only the upper left corner that is too long. I tried measuring the two with a caliper, but with the slope I couldn't get a consistent reading.

I just received 2 TTI +2 base pads yesterday. I tried them on 4 tubes. Two of them were too long and the other two just barely fit. It looks like he is pushing enough that it is not 100% that it will fit.

They restarted last fall, but only for the Form 1. Both individual and trust can use it. You do need to send in a set of prints after submitting the form.

I decided not to do a Google search for that term.

Is this what you are talking about? http://peacemakernational.com/supersteel They have rimfire listed, but it looks like just one division for all rimfire.

I sent in one of the RX models. I took out my Gray guns parts and sent it in. It came back with an 8 pound trigger pull. I'm looking forward to getting the updated GG parts to put in it.

I just do a big batch on my 650 and then clean with Simple Green afterwards. I use a cleaning rod with paper towels and a .45 jag to clean the tube.

Mine arrived Thursday last week.

I have had a deposit on the DT MDR since 2016.

Sounds like the perfect scope for the Desert Tech MDR.

I use Hornady one shot in the aerosol can on my .40 and 9x19 reloads to make it easier on my elbow. I just put some cases on a jelly roll pan and give them a quick spray. Then shake around a bit.

I just went and did the same to one of my Bladetech/SIG mag pouches. For me, I am doing this mostly as a way to improve on my classifiers.

Picture of rifle. Other changes are a Kidd single stage trigger and an Acculite graphite barrel from the late '90s.

0.5"

I have been using the Magpul X-22 Hunter stock since it came out and have been happy with it. Prior to that I was using a Hogue stock. At the same time I put on the Magpul stock I also switched to a Cmore sight on an Allchin mount. With the cheek riser kit I was able to get my comb height adjusted to work with the Cmore.