Ed F Posted December 5, 2021 Share Posted December 5, 2021 I thought I remember seeing someone who modified (made it ID larger) the end cap on a 929? Can't seem to find my link now:-( Link to comment Share on other sites More sharing options...
MWP Posted December 5, 2021 Share Posted December 5, 2021 Drill it out if you want to leave it on. Easiest thing to do is toss it in the trash. Link to comment Share on other sites More sharing options...
Ed F Posted December 5, 2021 Author Share Posted December 5, 2021 58 minutes ago, MWP said: Drill it out if you want to leave it on. Easiest thing to do is toss it in the trash. Well there is tossing in the trash, but then I would have modify my snazzy holster or get new holster made, re-crown the barrel. Being a general cheap ass, all the goes against my nature:-) Ed Link to comment Share on other sites More sharing options...
MWP Posted December 5, 2021 Share Posted December 5, 2021 I get it. The gun does look better with it on. Drill that cap out to 1/2” or larger and blue loctite the screw in with a lock washer. Should be ok for a few hundred rounds at a time. Link to comment Share on other sites More sharing options...
Ed F Posted December 6, 2021 Author Share Posted December 6, 2021 8 minutes ago, MWP said: I get it. The gun does look better with it on. Drill that cap out to 1/2” or larger and blue loctite the screw in with a lock washer. Should be ok for a few hundred rounds at a time. That would seem to be the way to go right now! Link to comment Share on other sites More sharing options...
Badkarma Posted December 6, 2021 Share Posted December 6, 2021 5 hours ago, Ed F said: Well there is tossing in the trash, but then I would have modify my snazzy holster or get new holster made, re-crown the barrel. Being a general cheap ass, all the goes against my nature:-) Ed Who made the holster? Link to comment Share on other sites More sharing options...
matteekay Posted December 6, 2021 Share Posted December 6, 2021 Are these all that poorly fit? I bought a used V-Comp and noticed the "comp" (using the term very loosely) had wear damage on the inner "ring" that's near the muzzle. Or maybe erosion? I was surprised because I know this is a very low-mileage gun. Link to comment Share on other sites More sharing options...
NoSteel Posted December 6, 2021 Share Posted December 6, 2021 (edited) I initially went with boring out the cap rather than removing because of the look without it. I finally ended up making it where it was no longer an issue (pic). The unfortunate part is the cap with the comp port is really not needed and has negligible affect on recoil. The other advantage to redoing the muzzle is most have noted how horrible the forcing cone & Muzzle crown were cut by S&W correcting that helps accuracy. You can do so much more with load adjustment. Not having the muzzle caps would have allowed a better design. Edited December 6, 2021 by NoSteel Link to comment Share on other sites More sharing options...
MikeyScuba Posted December 6, 2021 Share Posted December 6, 2021 All our end caps are gone. We did a classs with MWP and the first thing he told us to do was ditch em. Our guns look like the above ^^^^^ Link to comment Share on other sites More sharing options...
matteekay Posted December 6, 2021 Share Posted December 6, 2021 I didn't realize they were so awful. Other than being kinda stupid, do the end caps affect accuracy? Link to comment Share on other sites More sharing options...
mchapman Posted December 6, 2021 Share Posted December 6, 2021 2 hours ago, matteekay said: I didn't realize they were so awful. Other than being kinda stupid, do the end caps affect accuracy? Yes they will if you don't enlarge the muzzle hole or remove the cap all together. That is what I did, enlarge the hole so the bullet does not touch it when leaving the barrel and it does not lead up like it did prior to doing so. I left mine on so that I can continue using my HOGUE SPEED holster, which is NOT adjustable for different barrel lengths. Link to comment Share on other sites More sharing options...
Ed F Posted December 6, 2021 Author Share Posted December 6, 2021 17 hours ago, Badkarma said: Who made the holster? Sultac Mark Sullivan https://www.facebook.com/SulTac/ Link to comment Share on other sites More sharing options...
Ed F Posted December 6, 2021 Author Share Posted December 6, 2021 7 hours ago, NoSteel said: I initially went with boring out the cap rather than removing because of the look without it. I finally ended up making it where it was no longer an issue (pic). The unfortunate part is the cap with the comp port is really not needed and has negligible affect on recoil. The other advantage to redoing the muzzle is most have noted how horrible the forcing cone & Muzzle crown were cut by S&W correcting that helps accuracy. You can do so much more with load adjustment. Not having the muzzle caps would have allowed a better design. Yeah that is the long range plan Link to comment Share on other sites More sharing options...
matteekay Posted December 6, 2021 Share Posted December 6, 2021 5 minutes ago, mchapman said: Yes they will if you don't enlarge the muzzle hole or remove the cap all together. That is what I did, enlarge the hole so the bullet does not touch it when leaving the barrel and it does not lead up like it did prior to doing so. I left mine on so that I can continue using my HOGUE SPEED holster, which is NOT adjustable for different barrel lengths. Yikes. Seriously, S&W? Is it the same issue with the V-Comp? I think they interface similarly; I guess what I took to be erosion could have been projectile strikes. Link to comment Share on other sites More sharing options...
mchapman Posted December 6, 2021 Share Posted December 6, 2021 15 minutes ago, matteekay said: Yikes. Seriously, S&W? Is it the same issue with the V-Comp? I think they interface similarly; I guess what I took to be erosion could have been projectile strikes. Matt there is enough wiggle in the fit and slop around the retaining screw if it gets loose or is not secured in the exact same place every time after taking it off to clean and reinstall you will have issues, so just drill it out larger so it's not an issue. Link to comment Share on other sites More sharing options...
mchapman Posted December 6, 2021 Share Posted December 6, 2021 Here is a pic of a V COMP that MOJO worked over for Bruce. Link to comment Share on other sites More sharing options...
matteekay Posted December 6, 2021 Share Posted December 6, 2021 20 minutes ago, mchapman said: Matt there is enough wiggle in the fit and slop around the retaining screw if it gets loose or is not secured in the exact same place every time after taking it off to clean and reinstall you will have issues, so just drill it out larger so it's not an issue. Roger that. I had both caps refinished but the gun still isn't back home so I can probably drill them, have them TiN'd again, and get them back before I need them, lol. 16 minutes ago, mchapman said: Here is a pic of a V COMP that MOJO worked over for Bruce. MOJO's work always looks awesome. Link to comment Share on other sites More sharing options...
Ed F Posted December 7, 2021 Author Share Posted December 7, 2021 So used a step bit, drill clutch on 4 and ran it under cold water to keep it cool. Now it is time to send the cylinder off to TK for some chamfering and do a JM trigger job Link to comment Share on other sites More sharing options...
10mmdave Posted December 8, 2021 Share Posted December 8, 2021 Hmm, have the non fined muzzle cap on my 627 38 Super ever since I started using it, like 20-30 k plus rounds ago, filled the void between the barrel end and cap many times but never saw it affect accuracy, just removed the caked in crud with a center punch and a hammer (the OCD in me won't leave it alone) Can the opening "shrink" enough with fouling to cause an accuracy issue ?? Not sure, I've never seen it, but then I'm not a bullseye shooter. And sorry, but there is not enough "wiggle" to create an obstruction with the passing bullet, the original clearance diameter is more than enough for the bullet to pass through, let's not be starting any "old wives tales" about that BUT !!! if it's loose then all bets are off. Link to comment Share on other sites More sharing options...
ysrracer Posted December 9, 2021 Share Posted December 9, 2021 I had mine cut to five inches Link to comment Share on other sites More sharing options...
SSGGlock Posted December 13, 2021 Share Posted December 13, 2021 Has anyone just cut the nipple off with a hacksaw, filed flat and cut back in the crown? I can’t see it being that difficult, especially if you buy the Manson reamers. Link to comment Share on other sites More sharing options...
tomjerry1 Posted December 13, 2021 Share Posted December 13, 2021 ysrracer, what type of cylinder release is that? Link to comment Share on other sites More sharing options...
NoSteel Posted December 13, 2021 Share Posted December 13, 2021 1 hour ago, SSGGlock said: Has anyone just cut the nipple off with a hacksaw, filed flat and cut back in the crown? I can’t see it being that difficult, especially if you buy the Manson reamers. Yes. It takes a little time but if you go at it slow with good tools it’s possible. That’s how I got here. Used a bench mill initially on nub but hack saw is easy also used right. Link to comment Share on other sites More sharing options...
SSGGlock Posted December 13, 2021 Share Posted December 13, 2021 (edited) 13 minutes ago, NoSteel said: Yes. It takes a little time but if you go at it slow with good tools it’s possible. That’s how I got here. Used a bench mill initially on nub but hack saw is easy also used right. Don’t have access to a mill, but do have a portable band saw. I was going to buy the Manson Muzzle Crown Refacing Tool kit. Edited December 13, 2021 by SSGGlock Link to comment Share on other sites More sharing options...
NoSteel Posted December 13, 2021 Share Posted December 13, 2021 (edited) 35 minutes ago, SSGGlock said: Don’t have access to a mill, but do have a portable band saw. I was going to buy the Manson Muzzle Crown Refacing Tool kit. I just used an 11deg crowning reamer, .256 bushing, with a tap handle. Less then $100…. To get rid of the bolt hole drilled about 1 mm deep same diameter as stainless cap screw head for cap, lock tire it in and cut off/filed smooth. Edited December 13, 2021 by NoSteel Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now