RWingNJ Posted July 2, 2016 Share Posted July 2, 2016 Need Suggested Load:Intended Firearm: CZ 75 9mm w/ match barrelDivision: Production:Primer: Federal -Note Federal Primers are softer than CCI and same gr. power as CCI will produce a lower power factor.Bullet: Zero 147gr HPPowder: VIHTAVUORI N320 OAL: _______Gr:_________Desired Power Factor: 130- 135 Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted July 2, 2016 Share Posted July 2, 2016 Welcome to the Forums, RWingNJ Your best OAL is determined by running The Plunk Test, in your gun, and your mags, and with the bullet you selected. See what The Longest OAL you can use by removing the barrel, and dropping rounds of various lengths into the barrel - make sure you hear The Plunk, which indicates the round has dropped Completely into the chamber. Then, make sure you can spin the cartridge freely and that the round will drop out easily when you invert the barrel. The longest round you can find to pass The Plunk Test, is the longest OAL you can run - back that off by a little bit to ensure proper feeding, and you have it. Wow, that sounds like a lot of work, doesn't it? Just part of successful reloading that will end up with superior ammo suited for Your Gun. Whaja doin' with all this ammo? IDPA? USPSA? Steel? Link to comment Share on other sites More sharing options...
bowenbuilt Posted July 2, 2016 Share Posted July 2, 2016 (edited) 3.6 of N320 @ 1.135 OAL for a PF of 131. This is what works in my CZ 75 but my barrel has been reamed. As Jack said, you will need to tell us what your maximum OAL is and back off this load accordingly. Edited July 2, 2016 by bowenbuilt Link to comment Share on other sites More sharing options...
BlaineD Posted July 2, 2016 Share Posted July 2, 2016 3.4 gr Unique at 1.140 with 147 hp. Also 3.6 of 231 or 2.8 of Bullseye. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
accu9 Posted August 10, 2016 Share Posted August 10, 2016 2014 Shadow Custom/ Accushadow 147gr Zero JHP 1.10 OAL 3.4gr N320 132 PF Link to comment Share on other sites More sharing options...
MemphisMechanic Posted August 11, 2016 Share Posted August 11, 2016 I've never seen a noticeable difference in velocity by switching between Winchester, Federal, and CCI primers in 9mm minor loads, for what it's worth. Unless you plan to load just a touch above minimum power factor (a fools errand) then I wouldn't worry about it at all if your loads are running 130+ PF. Link to comment Share on other sites More sharing options...
chadxr650 Posted August 11, 2016 Share Posted August 11, 2016 I've never seen a noticeable difference in velocity by switching between Winchester, Federal, and CCI primers in 9mm minor loads, for what it's worth. Unless you plan to load just a touch above minimum power factor (a fools errand) then I wouldn't worry about it at all if your loads are running 130+ PF. how much of a difference and whats the numbers on the velocity? Link to comment Share on other sites More sharing options...
Hitman321 Posted August 17, 2016 Share Posted August 17, 2016 Put this on the CZ pistol section and decided to add it here as well.... CZ-75 Shadow (#91715) from CZC, all the bells and whistles, factory mags, ~800 rounds through the gun. Working up a load for the Zero 147gr JHP. Arrived at 3.5gr of N-320 which gives me a very consistent (SD of 7) velocity of 887 FPS (130 PF). Max OAL with this bullet was a way long 1.1813 which is obviously not going to work even after subtracting .015 from it. Apparently, my barrel has been reamed at some point but I didn't get an affirmative "yes" from CZC that they were the ones who did it (???). So I started at 1.135 and worked up to 1.155, 100 rounds total, measured each round then shot them in similar length blocks of 10, looking for an obvious increase in accuracy at 25yds. The fun began after loading the magazine with 10 rounds. I tried multiple mags. After 4-5 shots, the cuts on the hollow point section of the Zero bullets would "hang up" and nose dive internally on the magazine notch which locks the mag into the gun. Here's what's making me scratch my head... 1.135-1.1395 No issues 1.141 and 1.143 Hang up 1.144-1.146 No issues 1.1465 Hang up 1.147 No issues 1.1485 Hang up 1.149-1.155 No issues shooting over 30 rounds here The definition of inconsistency! Velocities were essentially the same on all shots but I did see a tightening group at the 1.147-1.148 range. So I guess I'll try shorter than 1.135 and shoot some more 1.147 and 1.150s to see if they remain reliable. Anyone else experience this or have any recommendations/solutions to offer? Link to comment Share on other sites More sharing options...
Hitman321 Posted August 17, 2016 Share Posted August 17, 2016 Accu9, What kind of accuracy are you seeing with your load below? 147gr Zero JHP 1.10 OAL 3.4gr N320 Link to comment Share on other sites More sharing options...
Diegoacostalo Posted October 19, 2018 Share Posted October 19, 2018 any more updates for this? I planning on using W231, which is comparable to N320. Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted October 19, 2018 Share Posted October 19, 2018 I love W231 (been using it since our American Civil War But, everyone here feels there are certain benefits to N320 , so probably not really comparable. I'd start around 3.2 gr W231 at 1.125" OAL, if your gun will load out that long Link to comment Share on other sites More sharing options...
Steve RA Posted October 20, 2018 Share Posted October 20, 2018 I'd have thought you'd have used Dupont or Laflin and Rand. Link to comment Share on other sites More sharing options...
IDescribe Posted October 21, 2018 Share Posted October 21, 2018 On 7/1/2016 at 10:17 PM, RWingNJ said: Primer: Federal -Note Federal Primers are softer than CCI and same gr. power as CCI will produce a lower power factor. Differences from one primer to the next vary based on case length and volume. The smaller the case, the less difference there is from one primer to the next. I have seen tests done with 9mm Luger with not only different brands of primers, but magnum vs standard. Difference between brands is negligible. Difference between magnum and standard is minimal. I'm talking minor difference in feet/sec here, as well. You're not going to see any difference in power factor in 9mm Luger with Federal vs CCI. Link to comment Share on other sites More sharing options...
Diegoacostalo Posted October 29, 2018 Share Posted October 29, 2018 3.4gr did it for me and my SHadow 2, thanks. Link to comment Share on other sites More sharing options...
MikieM Posted October 30, 2018 Share Posted October 30, 2018 To my way of thinking it's well worth the cost just because it's so clean burning. Add to that it's anti-fouling capabilities and it's as about as good as powder gets. Link to comment Share on other sites More sharing options...
Kema Posted October 30, 2018 Share Posted October 30, 2018 N320 needs SPM primer to have stable velocity. Some HP's need a very short col like 1.13 or less. I would start about 3.4gr. I don't know what the match barrel means here but usually CZ needs a bit more that other guns. Is this a typical production gun using original looking parts that have been fitted to look worn? Link to comment Share on other sites More sharing options...
IHAVEGAS Posted October 30, 2018 Share Posted October 30, 2018 12 hours ago, MikieM said: To my way of thinking it's well worth the cost just because it's so clean burning. Add to that it's anti-fouling capabilities and it's as about as good as powder gets. A lot of buzz about the somewhat new Sport Pistol powder being a cheaper alternative. Never bought VV because I never had a powder where I thought dirty burning was an issue, am about half way down on an 8 lb jug of SP though (147 gr 9mm loads) does seem like it is cleaner than what I'm used to. Link to comment Share on other sites More sharing options...
srrch Posted November 12, 2018 Share Posted November 12, 2018 N320 needs SPM primer to have stable velocity. Some HP's need a very short col like 1.13 or less. I would start about 3.4gr. I don't know what the match barrel means here but usually CZ needs a bit more that other guns. Is this a typical production gun using original looking parts that have been fitted to look worn?Kema , do you have any chrono data on magnum vs non magnum loads and N320?Sent from my SM-G930V using Tapatalk Link to comment Share on other sites More sharing options...
Kema Posted November 13, 2018 Share Posted November 13, 2018 No, I don't generally save pistol chrono data cause there are variations between same powder with different manufacturing runs. I always try to get lowest major/minor PF with thin marginal anyway. Link to comment Share on other sites More sharing options...
jripper Posted November 14, 2018 Share Posted November 14, 2018 I load 3.2 n320 at 1.12 OAL for 130 pf out of my S2. When I shot my S1 with .2" shorter barrel, it chronoed 128 pf. Link to comment Share on other sites More sharing options...
srrch Posted November 16, 2018 Share Posted November 16, 2018 I load 3.2 n320 at 1.12 OAL for 130 pf out of my S2. When I shot my S1 with .2" shorter barrel, it chronoed 128 pf. I get close to the same out of my LimPro.Sent from my SM-G930V using Tapatalk Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now