Prov1x Posted March 29, 2015 Share Posted March 29, 2015 When is someone going to post a how to video or demo pics? ;-) Link to comment Share on other sites More sharing options...
Adam B Posted March 29, 2015 Share Posted March 29, 2015 I opened the hole up for the larger pin and installed it in the gun. From there I test it, one of my stock 3's hardly needed any material removed the other 3 needed a small amount removed. Go slow and take a small amount off each time, it took about 1-1.5 hours per gun, lots of disassembly and reassembly but it was well worth it. Link to comment Share on other sites More sharing options...
AlphaSeeker Posted March 30, 2015 Author Share Posted March 30, 2015 Do not remove material from the face of the wing which gets pushed by the trigger bow. Thin the wing from the bottom to allow the bow to slip out of engagement. Link to comment Share on other sites More sharing options...
SD1 Posted March 31, 2015 Share Posted March 31, 2015 I spoke to Dave at Cajun GW. he is unaware of customers installing a Type 3 in a Tanfo Stock 3. I am assuming everyone is ordering online. Long story short, if he gets enough interest he is open to have a Tanfo Disco on the shelf, so blow his phones up and email him all that are looking. Link to comment Share on other sites More sharing options...
waktasz Posted March 31, 2015 Share Posted March 31, 2015 Done Link to comment Share on other sites More sharing options...
bpipe95 Posted March 31, 2015 Share Posted March 31, 2015 done. Also the email addy if anyone wants it. cajungunworks@gmail.com Link to comment Share on other sites More sharing options...
Adam B Posted March 31, 2015 Share Posted March 31, 2015 good to hear Link to comment Share on other sites More sharing options...
AlphaSeeker Posted April 1, 2015 Author Share Posted April 1, 2015 Look through my posts on this subject. Pictures and video included Link to comment Share on other sites More sharing options...
kgil275 Posted April 1, 2015 Share Posted April 1, 2015 (edited) I spoke to Dave at Cajun GW. he is unaware of customers installing a Type 3 in a Tanfo Stock 3. I am assuming everyone is ordering online. Long story short, if he gets enough interest he is open to have a Tanfo Disco on the shelf, so blow his phones up and email him all that are looking. Keeping my fingers crossed, that this may be the spark that ignites the flame Edited April 1, 2015 by kgil275 Link to comment Share on other sites More sharing options...
waktasz Posted April 1, 2015 Share Posted April 1, 2015 Dave is asking for dimensions for a prototype. Link to comment Share on other sites More sharing options...
bpipe95 Posted April 1, 2015 Share Posted April 1, 2015 Dave is asking for dimensions for a prototype. Received a similar reply. Anyone want to send him some parts? Link to comment Share on other sites More sharing options...
AlphaSeeker Posted April 1, 2015 Author Share Posted April 1, 2015 I'll call him with dimentions, on Thursday. Link to comment Share on other sites More sharing options...
Adam B Posted April 2, 2015 Share Posted April 2, 2015 (edited) When is someone going to post a how to video or demo pics? ;-) https://www.dropbox.com/s/gsjk5wgpnfi7kpo/IMG_0457.MOV?dl=0 Edited April 2, 2015 by Adam B Link to comment Share on other sites More sharing options...
AlphaSeeker Posted April 2, 2015 Author Share Posted April 2, 2015 Link to comment Share on other sites More sharing options...
Prov1x Posted April 2, 2015 Share Posted April 2, 2015 When is someone going to post a how to video or demo pics? ;-) https://www.dropbox.com/s/gsjk5wgpnfi7kpo/IMG_0457.MOV?dl=0 Is that the titan hammer? Link to comment Share on other sites More sharing options...
himurax13 Posted April 2, 2015 Share Posted April 2, 2015 Is there a version that shows how short the reset is after racking the slide? Link to comment Share on other sites More sharing options...
bpipe95 Posted April 2, 2015 Share Posted April 2, 2015 (edited) When is someone going to post a how to video or demo pics? ;-) https://www.dropbox.com/s/gsjk5wgpnfi7kpo/IMG_0457.MOV?dl=0 Is that the titan hammer?Oops!! thought he was talking about the youtube vid. Edited April 2, 2015 by bpipe95 Link to comment Share on other sites More sharing options...
Adam B Posted April 2, 2015 Share Posted April 2, 2015 It is the Titan and I have the EG trigger installed as well Link to comment Share on other sites More sharing options...
RobertLx Posted April 2, 2015 Share Posted April 2, 2015 Is there a version that shows how short the reset is after racking the slide? I wanted to see that as well. Hold the trigger in and rack the slide. Link to comment Share on other sites More sharing options...
Adam B Posted April 2, 2015 Share Posted April 2, 2015 the reset is no different when you rack the slide or just cock it https://www.dropbox.com/s/tfofnuwpbkozsca/Video%20Apr%2002%2C%207%2033%2006%20PM.mov?dl=0 Link to comment Share on other sites More sharing options...
himurax13 Posted April 2, 2015 Share Posted April 2, 2015 the reset is no different when you rack the slide or just cock it https://www.dropbox.com/s/tfofnuwpbkozsca/Video%20Apr%2002%2C%207%2033%2006%20PM.mov?dl=0 Well I would like to see how close the break is a few times just so I can get an idea of how it is in single action. Link to comment Share on other sites More sharing options...
Nealio Posted April 3, 2015 Share Posted April 3, 2015 People are wanting a video similar to this: Link to comment Share on other sites More sharing options...
AlphaSeeker Posted April 3, 2015 Author Share Posted April 3, 2015 Here you go: http://www.brianenos.com/forums/index.php?showtopic=194198&hl= This install is for Stock 3 with OEM sear. If running in SA, I don't think its necessary to swap out the oem sear. I spoke to CGW before ordering the parts, told him what it was for and was given advice on opening the pin hole in the sear. Adam's use of the diamond dremel bit is the best method I've used thus far. The job takes about 40min [second time around], if you do not have to fit a new sear to the safety. Wish I had video capability to demonstrate how simple it really is. Link to comment Share on other sites More sharing options...
himurax13 Posted April 3, 2015 Share Posted April 3, 2015 Here you go: http://www.brianenos.com/forums/index.php?showtopic=194198&hl= This install is for Stock 3 with OEM sear. If running in SA, I don't think its necessary to swap out the oem sear. I spoke to CGW before ordering the parts, told him what it was for and was given advice on opening the pin hole in the sear. Adam's use of the diamond dremel bit is the best method I've used thus far. The job takes about 40min [second time around], if you do not have to fit a new sear to the safety. Wish I had video capability to demonstrate how simple it really is. I thought fitting the sear to the safety was only needed if the Sear and or hammer was replaced? Link to comment Share on other sites More sharing options...
SD1 Posted April 3, 2015 Share Posted April 3, 2015 (edited) Did anyone give Dave@CGW a disco or specs? Edited April 3, 2015 by SD1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now