Jump to content
Brian Enos's Forums... Maku mozo!

himurax13

Classifieds
  • Content Count

    988
  • Joined

  • Last visited

About himurax13

  • Rank
    Calls Shots
  • Birthday 10/12/1974

Profile Information

  • Gender
    Male
  • Location
    Richmond, Virginia
  • Interests
    Invite me for drinks and I might share my interests with you.
  • Real Name
    John Jaramillo

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. himurax13

    CZ 75b extended safety

    I have purchased four CZ75 SA over the years, and they all have been tumbler style. The D Style sear cages are $69 plus the cost of the safeties that you add so this modification could easily be one of the most expensive one on the gun. The extended LHS Safety needs a lot of trimming in order to use properly.
  2. himurax13

    CZ 75b extended safety

    I have purchased four CZ75 SA over the years, and they all have been tumbler style. The D Style sear cages are $69 plus the cost of the safeties that you add so this modification could easily be one of the most expensive one on the gun. The extended LHS Safety needs a lot of trimming in order to use properly.
  3. himurax13

    COL for 147 plated round nose.

    1.150 should be fine for 124, 147, or 165g plated bullets. Coated bullets typically need to be seated deeper. A proper plunk and a pin test will let you know. As far as crimp is concerned, I use the least amount that I can get away with. I just make the walls straight. For the 147g profile, I would start my ladder loads at 2.8g. Depending on the gun/barrel, you could be close to the 125 Power Factor already.
  4. himurax13

    Brace yourself...it's coming

    What about selling a top end that is ready to go?
  5. So after rummaging through my pile of holsters and mag pouches, here is a pic of the best I was able to find. As I mentioned earlier, my Garret Industries Glock 19 Silent Thunder holster, tightened down, felt like a decent fit. For the mag pouches, I found this dual Kydex pouch for the CZ75/Berreta/Sig mags to be a decent fit with a little bit of tightening. Most of the similar sized individual mag pouches were too tight from front to back and a little loose from left to right. I don't think any pouches made for the regular 43 or a 1911 would work on the 43x/48 mags. The Ghost 360 and the Double Alpha pouches will work for the 43x/48 mags as well. Sent from my VS987 using Tapatalk
  6. That is what I saw on youtube videos, but I don't know if the current G43 mag pouches will accommodate the 43x/48 magazines. I found out that my G19 Garret Industries Holster will work for the 43x/48 just fine if I tighten the screws most of the way down.
  7. Can the regular 43 x Mag Carriers accommodate the larger 43x/48 magazines? Neither site stated that they would. Will 1911 Single Stag Pouches work for the 43X/48 Mags?
  8. himurax13

    Tritium Night Sights

    I saw a thread from a few years ago that Henning was going to offer these. I do not see anything listed on his site. Is anyone else making Tritium Sights for the Witness?
  9. I have been looking around and the gear available was made mostly for the regular 43 with limited compatibility for the new kinds on the block. Does anyone have a good lead on some gear I would actually use at a match?
  10. himurax13

    9mm major update for KKM Glock17

    Where did you find that deal? Sent from my VS987 using Tapatalk
  11. himurax13

    Witness Elite Stock 3 and IDPA

    Here is my Stock III. Somehow I doubt that I could get below 43 ounces with a mag unless some slide milling was involved as well. Sent from my VS987 using Tapatalk
  12. himurax13

    Slide Serrations Hard on Hands?

    Well if you are slingshotting instead of using the area between your support hand thumb and middle finger in an overhand fashion, I could see how that could happen. Sent from my VS987 using Tapatalk
  13. himurax13

    Fitting BOLO Disconnector in CZ 75

    If I decide to clean my S/A Shadow one of these days, I will pull out my hammer, strut, and disconnector. I went with a lightly polished short/wide CZ Competition hammer and a type 3 disco with the wing removed. My static reset is shorter than using the pre-travel screw on the trigger so I don't even use it. I run a 13 lb/blue hammer spring and the break feels like glass. The trigger pull is right around 2 lbs even.
  14. himurax13

    Witness Elite Stock 3 and IDPA

    The last time I weighed a 9mm Stock 3, with the stock grips and an empty magazine inserted, it weighed just north of 45 ounces. It should fit in the box since the Match Elite does.
  15. himurax13

    Is the Walther Q5 Match SF legal for SSP?

    How did that happen?
×