AHI

so what do you use to trim? use 2 tool heads

I stand corrected they now do make a pcc trigger https://velocitytriggers.com/product/ar-9mm-pcc-trigger/

Are we talking Brass prep with a 1500 trimmer? Or are you asking about do you need to size before you trim?

after 4 hours of post dumping he has his idem in the classifieds just my opinion but I could be wrong

As it says they do not.

Not to be used with 9mm conversions or other recoil operated conversions. right in the description https://www.brownells.com/rifle-parts/triggers-parts/triggers/ar-15-velocity-trigger-curved-prod94245.aspx read it your self if you do not bereave.

Go to the bottom of the page for what ever press you are ordering. The accessories are listed . So you can order them.

This is 16 years old

normal

Blue tip on primer magazine.May be damaged. Since its rifle are you swedgeing enough? ck adjustment. ck hold down adjustment. Does the primer bar move smoothly? If not why. Just a few ideas.

sorry if i up set you . you have a problem i have seen with some other reloaders. just tracking down the root cause. you have brass deposits on your expander ,trying to find out why , fyi I process brass for lots of people and now only wet clean rifle brass . in addition have been noticing a lot of issues related to wet clean methods. the brass is becoming less elastic

HOGRIDER Do you wet clean your brass? To me this appears to be the same problem you have been chasing acrost 3 different threds.

Yea I win my bet. Now how do I collect

set back will not be a issue with Dillon die it actually sizes the case smaller. Than the Lee. just not as close to the rim.

Copyright © 1958-2020 Lee Precision | 4275 County Road U | Hartford, WI 53027 | phone (262) 673-3075 | fax (262) 673-927 bottom of page

looks to me the pin is broken not something stuck on the end.

are you sure its not a .22 case stuck to the de cap rod? use 2 wrenches 1 on the top of the die the other on the decap rod nut. heat it up with a heat gun etc if necessary. hit decap nut wrench with a hammer sudden shock may break it loose. still would like to see a picture of this.

first clean everything . My primer system has the brass roller and I lube it with powdered graphite. Unless something (corn cob crud ) gets in it I have no issues. case feed issue. shell plate may be a little loose. Tighten till it locks up then loosen a little at a time till it indexes smoothly the tighten the 4 screws that keep it in position.Your case feed spring could be worn out maybe replace it with this one http://fastandfriendlybrass.com/shop/item.aspx?itemid=105

that's strange. Are You sure you don't have a crimp issue?

they have two different bullets with the same description this one https://www.brazosprecision.com/40-180gr-Flat-PointBevel-BaseGroove-583ct-0072bullet_p_17.html i can load to 1.140 and it works in multiple guns Glocks,1911 would have to shorten a little to fit a CZ this one https://www.brazosprecision.com/40-180gr-Flat-PointBevel-BaseNo-Groove-583ct-0072bullet_p_48.html never could get it to work except loaded in 40 s&w case to be fired in a 10mm at 1.180

are you saying that a primer stuck to the decaping pin .then it pulled back through the case? Lets see a picture of that. otherwise what sarge said.And through that case away if it did pull back through.

usually this starts at the flair /powder drop, not always. scraping happens at the seating die ,deposits at the crimp.

Hes got over 50 lets go see whats for sale.

MA is "universal" Dillon is caliber specific

it does not .it could be added but may defeat part of its use. give it a try. may actually be better.