taymag Posted December 19, 2016 Share Posted December 19, 2016 I wouldn't say I am an amazing shot so I have always got decent results with 1.100 but I can't be sure I am getting the best results I can. I got bored and did a search and was surprised that no one is really loading that short. I know I could load up some 1.140+ to test out but with a G17 what do you guys load to? I am shooting 3.5gr N320 coated cast at around 950fps Link to comment Share on other sites More sharing options...
Bullets Posted December 19, 2016 Share Posted December 19, 2016 3.3 gr n320 always worked nicely with 147s for me out of glock. 1.150 Link to comment Share on other sites More sharing options...
SCTaylor Posted December 19, 2016 Share Posted December 19, 2016 Loading shorter doesn't really hurt anything but doesn't help either, if the mags & barrel can accommodate longer. It's a common paradigm to load as long as possible, other than giving a bit more margin for error on powder chargers, I don't know why you have to load longer. Find your max oal with the plunk test, back it off about .005 and work your powder back up. I ran Bayou 147's at 1.135 in my G19 & 34. Now I'm shooting a Stock 2 that would only let me load to 1.10" so it was a requirement to go shorter. Link to comment Share on other sites More sharing options...
taymag Posted December 20, 2016 Author Share Posted December 20, 2016 44 minutes ago, 57K said: Unless they've changed recently, Glock 9mms will take loads longer than what will fit in the magazine. Very long throated and that's a good thing, IMO. One thing to keep in mind and confirm with your chronograph is that if you lengthen the load enough, pressure and velocity will lower. You will likely need to increase your powder charge. I load Hornady 147 gr. XTPs from 1.142"/29mm to 1.161"/29.5mm depending on the powder used. With a powder like N320 and a poly-coated bullet you wwon't need to increase the charge by much to stay at 950 FPS. Maybe .1 gr. and I very much doubt more then .2 gr. if that. Like SCTaylor mentioned, it's always a good idea to do the "plunk" test for any bullet. Very easy with jacketed in 9mm and with the polycoated, set OACL to 1.170" which is .001" longer than SAAMI spec and decrease OACL in .005" until you hear that good audible "plunk." Lengthening loads cuts down on bullet "jump" from the case to the rifling in the barrel. In this case with the long throat of the Glock, you might just want to look at 1.161"/29.5mm and confirm that it's not too long for the magazine. That just happens to also be the SAAMI recommend Max. OACL for the 9 x 21mm. Good info. Loaded some up and I wasn't able to go as long as I thought but I am bumping up at least a little. 1.142" looks familiar, I think that's someones factory info (maybe for N320?) but I remember that wasn't working for me Link to comment Share on other sites More sharing options...
rdinga Posted December 20, 2016 Share Posted December 20, 2016 I load 2 different 147's to 1.10 with good results. The Zero 147 JHP and the Precision Delta 147 FMJ-TC. I load for several different guns. 4.0 grains of WSF and a CCI primer. This load works well in all of them. In my load development, I tried several COAL. While conventional wisdom would say go with the longest COAL. When I went just a little shorter my results became much more consistent. Let the target and Chrono guide you. Link to comment Share on other sites More sharing options...
noylj Posted December 20, 2016 Share Posted December 20, 2016 Loading short with 147gn bullets could hurt--if the base of the bullet is being jammed into the case web. 147gn bullets at 1.145-1.155" works for me in MY guns. My 158gn L-SWCs are loaded at 1.145" Link to comment Share on other sites More sharing options...
njl Posted December 20, 2016 Share Posted December 20, 2016 It depends on the bullet/profile. With coated bullets, I like to minimize the amount of bearing surface above the case mouth. Some guns have a tendency to cut the coating during chambering if too much is exposed/unprotected. With Bayou's 147gr FP profile with a lube groove, I load out to around 1.14x". I just got my first batch of 147gr FP NLG bullets from H&S. To get minimal exposed bearing surface, I've been loading these to 1.005", which did seem kind of awfully short. I've only loaded a small test batch of these so far...and based on chronograph results, may drop the powder charge 0.1gr relative to what I use for the older style 147s. Link to comment Share on other sites More sharing options...
dauntedfuture Posted December 25, 2016 Share Posted December 25, 2016 Not all 147 fun bullets are make the same. I had to load zero's a little shorter then the precision deltas and the profile is different to get them to drop in my sti 9mm 2011. I'm loading about as long as I can with spacers in the magazines. Link to comment Share on other sites More sharing options...
mont1120 Posted December 25, 2016 Share Posted December 25, 2016 For my XDm, I load to 1.16, using 4.0 to 4.5 grains of 800X. Link to comment Share on other sites More sharing options...
jcc7x7 Posted December 25, 2016 Share Posted December 25, 2016 I shoot 147 Bayou's now because in my guns, 1911. 2011. Sig 226 and glock 34 they shoot the best and I can load them all at 1.135 they work in everything. i.e. one load for all the guns simplifies things for me. The 2011, 1911's will take longer loads but they don't seem to accomplish anything longer, i.e. feed better, more accurate etc. I've found BBI 147's have to be loaded shorter because of a different ogive on the the bullet. So test your bullet in your guns and go from there Link to comment Share on other sites More sharing options...
open17 Posted December 25, 2016 Share Posted December 25, 2016 3.4 N320, 147 Bayou, WSP primers, 1.140-1.145 OAL. Runs great and makes 129-134 pf (depending on which gun) in half a dozen Glocks, 2 CZ's , 2 1911's and a M&P Pro. Nice to have one load for all 9 minor. Heck--it will even run in 3 2011 Major 9 open guns without any changes, as well as a AR style PCC. Link to comment Share on other sites More sharing options...
texasref Posted December 27, 2016 Share Posted December 27, 2016 1.150" 147RN 3.5 VV N320 Link to comment Share on other sites More sharing options...
taymag Posted December 27, 2016 Author Share Posted December 27, 2016 1 hour ago, texasref said: 1.150" 147RN 3.5 VV N320 I think my bullets are bulging too much to get to 1.150. That is my exact load though at 1.100 Link to comment Share on other sites More sharing options...
adamge Posted December 27, 2016 Share Posted December 27, 2016 CZ Shadow and CZ TS 9mm 147grn plated truncated 1.095" with 4.45grn Silhouette makes 130PF in the Shadow and a little more in the TS. Link to comment Share on other sites More sharing options...
jbarnett50 Posted December 27, 2016 Share Posted December 27, 2016 147gr Bayou FP at 1.15 with N320 or HP38 for my Accushadow. Link to comment Share on other sites More sharing options...
pbairborne Posted December 27, 2016 Share Posted December 27, 2016 Seems that I'm loading a bit shorter than most. For my G34 and G17, I load Precision 147's, Eggleston 147's, and Acme 145 and 147's all to 1.125. I've been doing this for years and am happy with the accuracy. Link to comment Share on other sites More sharing options...
gerritm Posted December 28, 2016 Share Posted December 28, 2016 On 12/27/2016 at 0:47 PM, pbairborne said: Seems that I'm loading a bit shorter than most. For my G34 and G17, I load Precision 147's, Eggleston 147's, and Acme 145 and 147's all to 1.125. I've been doing this for years and am happy with the accuracy. We have been loading our 147's to this also. G17, 19, 34. gerritm Link to comment Share on other sites More sharing options...
taymag Posted December 29, 2016 Author Share Posted December 29, 2016 On 12/27/2016 at 1:47 PM, pbairborne said: Seems that I'm loading a bit shorter than most. For my G34 and G17, I load Precision 147's, Eggleston 147's, and Acme 145 and 147's all to 1.125. I've been doing this for years and am happy with the accuracy. Round nose or flat point? Link to comment Share on other sites More sharing options...
gerritm Posted December 29, 2016 Share Posted December 29, 2016 10 hours ago, taymag said: Round nose or flat point? Round nose 147gr Xtreme plated HP, 147gr Blue Bullets round nose, & PD 147gr JHP. All at the same OAL 1.12-1.13. We shoot them in our Glocks & his STI DVC 3-gun. Very soft accurate load with 3.2grs of Titegroup. gerritm Link to comment Share on other sites More sharing options...
HOGRIDER Posted December 31, 2016 Share Posted December 31, 2016 (edited) Match load for GSSF is MG 147fmj over 3.6g N320 @ 1.142. Works excellent in our 2 G17s and a G34. Drop to 3.3g for coated lead. Edited December 31, 2016 by HOGRIDER addition Link to comment Share on other sites More sharing options...
mjmagee67 Posted January 4, 2017 Share Posted January 4, 2017 I'll toss out my Tanfo S2, 1911, and M&P 9Pro load too 3.4gr N320 @ 1.135 with Fed of Win primers using coated 147gr flat nose bullets. that gives me a PF of 129-132ish. For my CZ and P226 I have to add .1gr to make PF. Link to comment Share on other sites More sharing options...
Red Ryder Posted January 5, 2017 Share Posted January 5, 2017 Match load for GSSF is MG 147fmj over 3.6g N320 @ 1.142. Works excellent in our 2 G17s and a G34. Drop to 3.3g for coated lead. I use those same recipes, OAL 1.132 to 1.142. I found very little chrono differences in this range. I keep it simple and use 1.135. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
taymag Posted January 5, 2017 Author Share Posted January 5, 2017 (edited) 34 minutes ago, Red Ryder said: I use those same recipes, OAL 1.132 to 1.142. I found very little chrono differences in this range. I keep it simple and use 1.135. Sent from my iPhone using Tapatalk Forgot to check back in after posting this hah. Anyway, after seeing all the 1.130-1.142 posts I decided to try and figure out what the hell was going on.. When I setup my new dies apparently I wasn't taking enough of the bell out, so the rounds were not plunking, which is why my OAL issue was driving me crazy thinking I had to load so short, which I knew was wrong since I have a Glock barrel. There was a veryyyy fine line of closing the bell, not leaving a crimp mark or smashing the bullet .001 or so (apparently I just got lucky setting up my dies before on my other press, cause everything was perfect). Ran 300 rounds or so with the 3.3-3.4gr N320 at 1.135" recipe and everything seems to finally be perfect, cycled good and felt good Thanks again for the help. This forum defiantly blows the others out of the water in the reloading section, not sure why it took so long to make it over here after seeing the mention on other forums for years Edited January 5, 2017 by taymag Link to comment Share on other sites More sharing options...
MikieM Posted January 6, 2017 Share Posted January 6, 2017 On 12/27/2016 at 0:47 PM, pbairborne said: Seems that I'm loading a bit shorter than most. For my G34 and G17, I load Precision 147's, Eggleston 147's, and Acme 145 and 147's all to 1.125. I've been doing this for years and am happy with the accuracy. Good answer, here. Plunk a loaded round into your barrel, then turn it to ensure that you are not contacting the lands. If you happen to load a bunch of ammo that is too long it's no big deal to go back and re-seat and re-crimp them to the length you want. Link to comment Share on other sites More sharing options...
Red Ryder Posted January 7, 2017 Share Posted January 7, 2017 Forgot to check back in after posting this hah. Anyway, after seeing all the 1.130-1.142 posts I decided to try and figure out what the hell was going on.. When I setup my new dies apparently I wasn't taking enough of the bell out, so the rounds were not plunking, which is why my OAL issue was driving me crazy thinking I had to load so short, which I knew was wrong since I have a Glock barrel. There was a veryyyy fine line of closing the bell, not leaving a crimp mark or smashing the bullet .001 or so (apparently I just got lucky setting up my dies before on my other press, cause everything was perfect). Ran 300 rounds or so with the 3.3-3.4gr N320 at 1.135" recipe and everything seems to finally be perfect, cycled good and felt good Thanks again for the help. This forum defiantly blows the others out of the water in the reloading section, not sure why it took so long to make it over here after seeing the mention on other forums for yearsI am wondering about your reloading skills, so here is the best practice. Using digital calipers, the finished case should measure .376 to .379 at the very top of the rim. Less means your crimping. More and your round won't case gauge well. The goal is to remove the bell and avoid crimping. If I remember correctly, spec is .380. Glocks have sloppy barrels and may even feed up to .382. So barrel checking is preferred by some shooters. Some barrels are tighter than others. This becomes really important if you're using coated or plated Bullets. A tight crimp could cause the coating to scrape off negating its benefits and can even cause bullet tumbling issues. FMJ bullets are a tad bit more forgiving with a tighter crimp. Good luck. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now