ES13Raven Posted June 23, 2014 Share Posted June 23, 2014 I plan on get a Dillon 550, and will be using it for my G34 and G35 (minor & major). Since all of my brass will be "glocked" - should I buy non-Dillon dies like the Lee 4-Die Deluxe Set with Carbide Factory Crimp Die? Or buy Dillon Dies and also a EGW Undersize Die? What is the best plan for my dollar? Link to comment Share on other sites More sharing options...
LoganbillJ Posted June 23, 2014 Share Posted June 23, 2014 I run a 650 with the lee die set. 90% of my brass is glocked. I run my loads in a 22 with a kkm barrel and have zero issues with feeding. My Lee's have served me well. I have not run the other setup you mentioned so cannot help you there. Link to comment Share on other sites More sharing options...
Kraj Posted June 23, 2014 Share Posted June 23, 2014 I use a GRX die that resizes the whole case. It takes a little longer because you have to do it on a single stage press, but it fixes "glocked" brass Link to comment Share on other sites More sharing options...
Prebaned Posted June 23, 2014 Share Posted June 23, 2014 Your best plan for your dollar would be get the Lee set. I have it set up on my 650 and when set up properly it sizes my Glocked brass perfectly and shoots fine in my non-Glock handguns. No need for a U die or any undersized die. Sent painfully from my iPhone 5 using Tapatalk Link to comment Share on other sites More sharing options...
tray999 Posted June 23, 2014 Share Posted June 23, 2014 I plan on get a Dillon 550, and will be using it for my G34 and G35 (minor & major). Since all of my brass will be "glocked" - should I buy non-Dillon dies like the Lee 4-Die Deluxe Set with Carbide Factory Crimp Die? Or buy Dillon Dies and also a EGW Undersize Die? What is the best plan for my dollar? I have G22, G27, G34, and G35 and use Dillion 9mm and 40SW dies with my 550 and have not had one issue with "glock brass". I just make sure my re-sizing die is all the way down and no issues. I have loaded thousands of 9mm and 40SW wiith mixed brass without any problems. Link to comment Share on other sites More sharing options...
vluc Posted June 23, 2014 Share Posted June 23, 2014 Your best plan for your dollar would be get the Lee set. I have it set up on my 650 and when set up properly it sizes my Glocked brass perfectly and shoots fine in my non-Glock handguns. No need for a U die or any undersized die. Sent painfully from my iPhone 5 using Tapatalk Guess I'll have to reset my Lee on my 650, get a handful every couple hundred that won't gauge. Link to comment Share on other sites More sharing options...
427Cobra Posted June 23, 2014 Share Posted June 23, 2014 I run all 40 brass thru a Lee Bulge Buster, same thing as a Redding GRX for 1/3 the price, as for 9mm Dillon dies on my 650 work perfectly. Link to comment Share on other sites More sharing options...
Cowboy1629 Posted June 23, 2014 Share Posted June 23, 2014 I run glocked 9mm and 9 major through my 650 but I do use the U-die in station 2 and the regular Dillon 9mm die in station 1. I believe all the rounds would work in my guns without the U-die however they won't all pass the case gauge without the U-die. Link to comment Share on other sites More sharing options...
Laughingdog Posted June 23, 2014 Share Posted June 23, 2014 You really don't have to worry about the G34. I have a 550, and have never had a round of 9mm not pass case gage after being sized by the Dillon die. Case gaging issues with 9mm have always been related to the bullet. If you do have any that don't pass case gage, pull it, run it through the same dillon die again, and you'll find that piece of brass drops in a case gage (even an EGW one) perfectly. Now .40 can be a whole different matter. Link to comment Share on other sites More sharing options...
RDA Posted June 26, 2014 Share Posted June 26, 2014 "Glocked" brass doesn't mean all calibers of Glocks. The primary culprit of "Glocked" brass is .40S&W and only certain generations of Glocks that had poorly supported chambers. I have never seen one bulged case from my 9mm and .45 Glocks. Link to comment Share on other sites More sharing options...
daves_not_here Posted June 26, 2014 Share Posted June 26, 2014 With the EGW undersize die for 9mm it is rare to get a round that won't gauge. I stopped gauging my practice brass. The usual reason for a round to hang up in the gauge is extractor marks. DNH Link to comment Share on other sites More sharing options...
rdinga Posted June 26, 2014 Share Posted June 26, 2014 I run range pick up brass through my square deal without any issues to feed all of 9mm glocks. Before having a dedicated 9mm press, i loaded on the 550 using Dillon dies and never had a problem. Link to comment Share on other sites More sharing options...
vluc Posted June 27, 2014 Share Posted June 27, 2014 You really don't have to worry about the G34. I have a 550, and have never had a round of 9mm not pass case gage after being sized by the Dillon die. Case gaging issues with 9mm have always been related to the bullet. If you do have any that don't pass case gage, pull it, run it through the same dillon die again, and you'll find that piece of brass drops in a case gage (even an EGW one) perfectly. Now .40 can be a whole different matter. I never had issues on my 550. My 650 is the problem child that gives me the occasional fat boy. Link to comment Share on other sites More sharing options...
stick Posted June 28, 2014 Share Posted June 28, 2014 I run Lee dies in my XL650 and I only shoot Glocks. I really like the factory crimp die. Link to comment Share on other sites More sharing options...
John Wayne Posted June 28, 2014 Share Posted June 28, 2014 9mm Glock police brass, Dillon dies, no problems with no go gauge. Link to comment Share on other sites More sharing options...
MikeHunter Posted June 29, 2014 Share Posted June 29, 2014 My brass, my glock brass, range brass, any brass, no issues in 9mm. Sent from my iPad using Tapatalk HD Link to comment Share on other sites More sharing options...
BattleCreek Posted June 29, 2014 Share Posted June 29, 2014 why is GLOCK brass an issue?? are we saying a striker fired brass somehow deforms?? or is it the Dillon sizer die causing an issue?? I can't wrap my mind around this... then again I have yet to reload 1 round.. Link to comment Share on other sites More sharing options...
b1gcountry Posted June 29, 2014 Share Posted June 29, 2014 (edited) Someone will give you a better answer, but the glock barrels have a looser chamber, so the brad expands more than it would when fired from a different pistol. I believe this was intentional by glock to make the gun more reliable. But long story short, brass fired from a G22 will be oversized compared to other platforms. When reloading this brass for those other platforms, resizing is more important to get right. Edited June 29, 2014 by b1gcountry Link to comment Share on other sites More sharing options...
DonLucky13 Posted June 29, 2014 Share Posted June 29, 2014 "Glocked" brass doesn't mean all calibers of Glocks. The primary culprit of "Glocked" brass is .40S&W and only certain generations of Glocks that had poorly supported chambers. I have never seen one bulged case from my 9mm and .45 Glocks. re read this post, this is the answer! Link to comment Share on other sites More sharing options...
BattleCreek Posted June 29, 2014 Share Posted June 29, 2014 I skimmed most this thread and jumped to post earlier.... lol I just followed several old links/ stickies regarding "glocked" brass....WOW there is much to read, and lots of people with a LOT of opinions, and scenarios to fix the 'problem'... I have to admit this is the first time I've ever even heard of this, same token I've never reloaded either... I'm getting a press soon and will try the dillon dies it comes with and will check each round in the gage just to be sure... most reloading videos I've seen they just load 100 or so and reach in and grab a few rounds put it in gage and call the whole batch good... do you guys check each round?? Link to comment Share on other sites More sharing options...
Steve RA Posted June 29, 2014 Share Posted June 29, 2014 I'd suggest using the chamber of the barrel (out of gun) you plan to shoot them in as a check device. I'd also only do it for match ammo, if it happens in practice, it's good training in gun clearing practices. Link to comment Share on other sites More sharing options...
RangerTrace Posted June 29, 2014 Share Posted June 29, 2014 100% of my 40 brass comes from a local PD who shoots Glocks. I use a Lee U die in my 650 and I have only had two rounds fail the case gauge in the last 4 years. It works so well, that I only check major match ammo. Link to comment Share on other sites More sharing options...
pjames32 Posted July 17, 2014 Share Posted July 17, 2014 I bought range brass to load my 40 S&W. Using a SDB I had about 30% fail to pass the gauge. I single sized a couple hundred rounds with my RCBS carbide die, then loaded with the SDB. My fail rate dropped to about 5%. My caliper indicates about .002" larger. The "no go" rounds seem to go thru my M&P hand cycling. I'll get to the range in a few days to try the "no go" rounds. Link to comment Share on other sites More sharing options...
Kaskillo Posted July 18, 2014 Share Posted July 18, 2014 (edited) I run all brass thru my custom built sizer..... up to 3k per hour. You won't size the and base using the standard sizing dies from any manufacturer. You have to either "roll size" or "push thru size". My sizer takes care of the "bulge" and rim. Edited July 18, 2014 by Kaskillo Link to comment Share on other sites More sharing options...
Retread1911 Posted July 18, 2014 Share Posted July 18, 2014 I run all brass thru my custom built sizer..... up to 3k per hour. You won't size the and base using the stander sizing dies from any manufacturer. You have to either "roll size" or "push thru size". My sizer takes care of the "bulge" and rim. What kind of sizer do you have? As for the OP your advice thus far is correct. Either roll size or push through size are the only way to guarantee range or glocked brass will gauge. For me I push through sized for a few thousand rounds and then found a case pro used. Now all I use the push through die for is a stand. Gt. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now