AHI

I have two loads a 75/77 (depends on witch rifle) for 200 out and spinners.and a 55/60 for zero to 200. Rifle is zeroed for 200.

teflon tape will fix your issue

#1 you have no idea what velosity your current load is. #2 G19 not ideal for major it will work for a while but. #3 you asked a yes/no question. #4 there is more to loading major than just adding more powder. What may be safe in one gun may make parts fly in another. You have no idea what velosity your current load is . So do you have a chrono? Again there is more to loading major than just adding more powder.

NO

As stated above #1 you need a hotter spark you can try cci small pistol magnum primers (550) #2 increase power factor alittle ( your actually increasing pressure)Major Pistol/AA7 need pressure to burn cleaner. The lot of AA7 that I have is cleaner than the lot of MP that I currently have (next lot it may change.)#3sizing the brass holds the bullet not crimp. #4crimp will not cause your issue.#5 sweet spot for me was 9.8 (also the recommended load from Atlas)

If I may suggest a load used by some NRA precision pistol shooters 160 swc 4.0 -4.5 Bullseye powder 1.175 length http://www.brazosprecision.com/45-160gr-Button-NoseFlat-BaseGroove-656ct-0064bullet_p_52.html then after a while if you wont more recoil 230 RN 3.6-4.0 Bullseye 1.250 length

The ones I have yes you can see the rounds.

Black Dog http://blackdogmachinellc.net/AR15.22PRODUCTS.aspx

Youndering did you melt the coated bullets with gun powder?

Yondering not disagreeing with you but. All coated compared to JHP bullets smoke more. My theory is that the coating is being burnt to some extent . Not enough to remove it just a reaction causing the smoke . Have seen lots of guns smoke with out leading with coated bullets. Recovered bullets have no damage to the coating.

OP where is your phone? A smart (ass) phone (the worst) old style cell or even land line cordless will interfere with digital scales.

I am running 7.3+ autocomp in a SPS Vista short no psi 168/170 PF

its the Blues Precision Delta 124 JHP with Autocomp is what I run no or very little smoke.

Been over a week report? Other than real high where does it hit now?

one of that can be turned around( un bolt from mount)? https://www.primaryarms.com/holosun-hm3x-3x-magnifier https://www.primaryarms.com/sig-sauer-juliet-3-magnifier-with-qr-mount https://www.primaryarms.com/vortex-optics-micro-3x-magnifier

adjust by 3 shot groups not individual shots. Gun may not like the ammo you are shooting. I know at 25yards ammo should not matter but it may.

I see both 9mm and 9x18 (makarov) listed.https://www.midwayusa.com/product/1011209519 I dont use a bulge buster but have used the redding version for 40s&w and do have a lee factory crimp die the sizing portion is only about 10mm long. once the case is pushed in if the press was upside down the case/loaded round would fall out. its not recommended to run live ammo through but it can be done.

Other than to just know what brand of case . what would be wrong with just separating by head stamp then prep/load? Start low and work up.

Is this a purpose built 9mm or a 223 converted to 9mm with an adapter of some type? other wise just one discussion on buffer systems there are more

yes it does and also flairs as well

try adjusting the sedge hold down . it expands the mouth. next adjust the mr bullet feeder expander a little more(powder drop) both of these do pretty much the same job a M die does. mr bullet powder funnels are known to wear out so to speak.

go hear https://shootersworldpowder.com/

zero in at 50 yards then see were it hits at closer range as suggested above. 8 out of 10 times this fixes windage issues.

https://afte.org/resources/headstamp-guide look at these

Happy searching https://afte.org/resources/headstamp-guide