MikieM Posted December 13, 2017 Share Posted December 13, 2017 Went to the range and went through maybe 150 rounds of ammo when all of a sudden it quit firing. I would eject a loaded round and click. No bang. After several attempts to load and fire I put the gun in the bag and went home. I did, however, pick a few of the un-fired rounds from off the ground and took them with me. At home I took a look at the rounds that didn't fire and each one has a very faint mark where the firing pin nicked it. Very faint. I haven't taken the bolt out of the gun, yet, but is this an indication of a broken firing pin? If so, what is the best available pin and spring on the market for the AR9? It's a Taccom bolt, by-the-way. Thanks, Mike. Link to comment
JAFO Posted December 13, 2017 Share Posted December 13, 2017 Inspect the tip of the pin to see if it's damaged. If not, check to make sure there's nothing in the FP channel to impede the forward movement. I've seen failures to fire in pistols that had oil in the channel, for example. You could push the pin out to its full extension by hand, but backpressure from trying to compress the oil would keep it from hitting hard enough to ignite a primer. Link to comment
Aircooled6racer Posted December 13, 2017 Share Posted December 13, 2017 Hello: Take the firing pin out and have a look at it. It may have a bent spring or a broken firing pin. I would contact Tim at Taccom and get a new firing pin if it is broken. Thanks, Eric Link to comment
Xanatos903 Posted December 13, 2017 Share Posted December 13, 2017 JAFO's got the best solution. Check the firing pin, then if it's not broken, check your firing pin channel. The 9mm firing pins don't hold up well, especially if you do any amount of dryfire that actually involves dropping the hammer. I've broken two firing pins and sheared a retaining pin from dryfire. I'm using CMMG firing pins, and I keep a couple extras in my bag at all times. Link to comment
MikieM Posted December 13, 2017 Author Share Posted December 13, 2017 Yep. Took the bolt out and sure enough, broke right in the middle. Thanks, all. Link to comment
L9X25 Posted December 13, 2017 Share Posted December 13, 2017 @MikieM What trigger are you running in that gun? Dryfire much? Link to comment
MikieM Posted December 13, 2017 Author Share Posted December 13, 2017 1 minute ago, L9X25 said: @MikieM What trigger are you running in that gun? Dryfire much? It's a Hiperfire 24C, with a shoe. Little, or no, dry-fire. Link to comment
stick Posted December 14, 2017 Share Posted December 14, 2017 I hope I don't jinx myself, but I haven't broken a firing pin yet. I run a Hiperfire 24C and I dry fire the gun 5-6 days a week. Link to comment
MikieM Posted December 14, 2017 Author Share Posted December 14, 2017 Probably just bad luck. I ordered a new one from Rock River, an hour or so ago. Link to comment
stick Posted December 14, 2017 Share Posted December 14, 2017 Just now, MikieM said: Probably just bad luck. I ordered a new one from Rock River, an hour or so ago. I've heard good things about the Wilson Combat bullet proof 9mm firing pins. I need to order one! Link to comment
MikieM Posted December 14, 2017 Author Share Posted December 14, 2017 28 minutes ago, stick said: I've heard good things about the Wilson Combat bullet proof 9mm firing pins. I need to order one! I almost did, and probably will the next go around. Link to comment
brytec Posted December 14, 2017 Share Posted December 14, 2017 Had the same problem after maybe 500 rounds and saw same issues with the faint primer marks... took the bolt apart and saw firing pin broke! Tried other firing pins but the only thing that fits/works was the original spinta FP. So called them and they replaced it for free. 6k later and still working. Link to comment
MikieM Posted December 14, 2017 Author Share Posted December 14, 2017 I appreciate it. Thanks. Link to comment
Bwilmot Posted December 14, 2017 Share Posted December 14, 2017 After 400 rds my firing pin spring broke in the middle of a match. Now I carry spare pin and springs Link to comment
Les Snyder Posted December 14, 2017 Share Posted December 14, 2017 I've posted this before, but after an initial 400 round break with an OEM pin, replacing it with a real Colt, and rounding the strike surface has produced a trouble free 2500 or more string, including changing bolts... my perception is that rounding allows the hammer to strike the pin closer to the center line of pin travel Link to comment
longbeard Posted December 14, 2017 Share Posted December 14, 2017 I've had more than one break on me. Pretty much realized it's a part you need to carry. Also have had the springs break so I carry those as well. Why they break? I gave up trying to figure it out. This goes for the pistol type extractors too. Get an extra and fit it so you can swap it out when it breaks on the range. Link to comment
RAINY0DAYS Posted December 14, 2017 Share Posted December 14, 2017 Same bolt, same trigger, same broken firing pins. Skip the Wilson, I tried one and it broke after a few hundred rounds. I think the tool steel they use is just too brittle. I'm currently trying the pin from AR15xtreme, and so far I think it's the best made of the bunch. The step in the middle where they commonly break is more tapered, and I think the 17-4 stainless will hold up a little better. I still have two spares in my range bag though. Tim is currently working on making a new firing pin for those of us who keep breaking them, so looking forward to that. Link to comment
stick Posted December 15, 2017 Share Posted December 15, 2017 11 hours ago, RAINY0DAYS said: I'm currently trying the pin from AR15xtreme, and so far I think it's the best made of the bunch. The step in the middle where they commonly break is more tapered, and I think the 17-4 stainless will hold up a little better. Does the extreme come with a spring? Link to comment
RAINY0DAYS Posted December 15, 2017 Share Posted December 15, 2017 Does the extreme come with a spring?No. I ordered a bunch of spare cmmg springs from primary arms.Sent from my Moto G (4) using Tapatalk Link to comment
DFABOVE Posted December 15, 2017 Share Posted December 15, 2017 Are the firing pins a standard configuration like .556 ARs?I built my AR 9 using a PSA complete upper and have about 500-600 rounds down range.I would like to pick up whatever spares that are needed in advance.I haven't been able to shoot since I first got the gun sorted out (leg brace) from surgery. Link to comment
RAINY0DAYS Posted December 15, 2017 Share Posted December 15, 2017 1 hour ago, DFABOVE said: Are the firing pins a standard configuration like .556 ARs?I built my AR 9 using a PSA complete upper and have about 500-600 rounds down range.I would like to pick up whatever spares that are needed in advance.I haven't been able to shoot since I first got the gun sorted out (leg brace) from surgery. For the most part, with a few exceptions like the JP. Link to comment
Flatland Shooter Posted December 16, 2017 Share Posted December 16, 2017 2 hours ago, RAINY0DAYS said: For the most part, with a few exceptions like the JP. From an earlier post it sounds like Spinta also has a proprietary firing pin. Kinda sucks since I have two Spinta bolts and a whole bunch of spare generic firing pins that may not work. Link to comment
MikieM Posted December 16, 2017 Author Share Posted December 16, 2017 I've got two Spinta pins coming in. From the picture, and description, they look just like everyone else's. Link to comment
L9X25 Posted January 29, 2018 Share Posted January 29, 2018 Shot a six stage match today and had a failure to fire on the 3rd stage, my first malfunction ever with this carbine. Racked it out so quickly that I could not find it, assumed it was just a high primer. Next stage it randomly happened again. Took it to the safe area and the pin was snapped in half. I cleaned everything and dropped the pieces back into the bolt. Was able to continue with only one more FTFire, but it was on my mind the whole time. Just a bit of trivia, JP firing pins will not work with many other bolts. Also, this is with a JP trigger with the yellow (light) hammer spring. PUT A SPARE FIRING PIN IN YOUR SHOOTING BAG. Link to comment
stick Posted January 29, 2018 Share Posted January 29, 2018 Well it finally happened. Went to the range to practice....5 rounds in click not bang. I assumed it was the firing pin, so i pulled it out and checked it. The firing pin was fine. I thought it was stepped brass. Nope! Frustrated I went home. The next day, I decided to clean the gun. When I took out the firing pin and removed the spring. I found the problem. a broken firing pin spring. The moral of the story when checking the firing pin, remove the spring from the firing pin and check it too. I had two extra firing pins and two extra springs in my bag. I dry fire the gun 5-6 days a week with my Hiperfire 24C installed. I'm thinking I'm going use a dedicated firing pin/spring for matches and one for dry fire/practice. Link to comment
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now