xracer Posted September 17, 2014 Share Posted September 17, 2014 Is this a true statement or not? The longer the COL the better as long as it doesn't engage the rifling when chambered and feeds properly(fits in the magazine). I recently heard of someone loading to 1.09" and thought "thats a little short" Looking at it from an accuracy standpoint. Link to comment Share on other sites More sharing options...
kneelingatlas Posted September 17, 2014 Share Posted September 17, 2014 (edited) "Better" is to simple a concept. More case volume means less pressure in a given load, that's the main reason to load long when using heavy bullets and fast powders as so many of us like to although if overpressure is not a concern with your particular combination of powder and bullet, I don't see any problem with loading shorter than SAAMI specs. As for accuracy: I don't know... I'm not yet to the stage of my load development where I'm tuning OAL for accuracy, but I have heard some people swear by the accuracy of shorter loads. I started reloading primarily to shoot 9 major, so my first priority has always been to make major and not blow up the gun, then to cycle reliability, then to produce as much gas as possible to work the comp, then accuracy. I haven't made it that far yet Edited September 17, 2014 by kneelingatlas Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted September 17, 2014 Share Posted September 17, 2014 I've loaded 9mm major to 1.145" out to 1.170", and found no difference in accuracy. By 9mm minor is slightly more accurate with a slightly shorter OAL, but doesn't feed as well, so I load a little longer and lose a little accuracy. If you enjoy tweaking the most out of your handloads, start with the longest OAL your mag/chamber will take, and then experiment with shorter OAL's also, to see which is "best" for YOU. Link to comment Share on other sites More sharing options...
johnsons1480 Posted September 17, 2014 Share Posted September 17, 2014 With my Glock 34, I did one test at max length to get to power factor. So I loaded at 1.155 and bumped the powder until I got to a little over 125 power factor. Then I loaded 10 each OALs from 1.085" to 1.155" in .01" increments. Then I shot these all for groups. I found in my gun, with my load, 1.125" shot the most accurately, had no feeding problems, and made about 130 PF. I shot from 1.155" down, checking velocity and for pressure signs at each step. Even at 1.085", I think I was only at 134 PF. So, after establishing that 1.125" shot the most accurately and made PF, I loaded up 200 of them and shot them in a local match (I don't have anywhere I can currently shoot that allows me to simulate match conditions. Probably a better idea to try this in practica). They functioned flawlessly, and now I have my load. That's my process, hope it will help you. Link to comment Share on other sites More sharing options...
1SOW Posted September 18, 2014 Share Posted September 18, 2014 Loading them deeper in the case provides better assurance of a concentric bullet seat. The bullet also doesn't get 'knocked' out of being concentric hitting the feed ramp. YMMV Link to comment Share on other sites More sharing options...
BeerBaron Posted September 18, 2014 Share Posted September 18, 2014 The thing is you cannot just make a blanket rule. different guns behave differently. even guns of the same model but different actual guns behave differently. All I can say is, don't just accept that longer is better. do something like johnsons1480 did. Basically what I do is pick the bullet I'm going to use, the powder and the primers (for 9mm I use a mix of brass, if you want to get scientific use same headstamp and trim to length too - too hard for me). once ive got a load at a nominal OAL (say 1.100) that makes the PF I want (usually around 130 for minor) then I load up a bunch with different OALs. In my CZ I went as short as 1.070 and up to whatever was the longest I could load (from memory around 1.130, something like that). In my particular CZ (in fact in 2 of them) I found group size closed up quite a bit as I got shorter. I settled on 1.080 as the best compromise between reliable length and accuracy. but again, that's with a particular bullet (135GN RN CMJ - frontier brand), powder and primer combo. many others find in their gun, with their bullet longer works better. so my advice? experiment a little with your own gun and your own load. it actually doesn't take as long as you think. you have to review the results with a grain of salt as there's a human factor in there (unless you mount the gun in a ransom rest). I usually shoot the groups supported with some kind of rest at 15 yards. when I've got say the 3 best I then shoot a few more off hand the way I normally shoot to see how they 'feel' to shoot too. Link to comment Share on other sites More sharing options...
kneelingatlas Posted September 18, 2014 Share Posted September 18, 2014 This is why reloading is so frustrating/fun/rewarding, there are enough variables to make your head spin! Link to comment Share on other sites More sharing options...
bayougump Posted September 18, 2014 Share Posted September 18, 2014 This is why reloading is so frustrating/fun/rewarding, there are enough variables to make your head spin! So true Link to comment Share on other sites More sharing options...
truborshooter Posted September 18, 2014 Share Posted September 18, 2014 johnsons1480, Just out of curiousity, can you share you data on all the loads from 1.085 - 1.155? I'd be interested in the differences as oal changed throughout the range. Also, what bullet and case did you use? thanks Link to comment Share on other sites More sharing options...
johnsons1480 Posted September 18, 2014 Share Posted September 18, 2014 Unfortunately, I was using Chrono Log to document the velocities (terrific app btw), and I had to wipe my phone recently and lost all of the velocity data except for the load I ended up with. I can show you the group sizes at 25 yards and the screenshot of the one load I have though. I used Bayou Bullets 135 gr RN, Federal Cases, Federal Match SPP 10 Shot Group Sizes 1.085 OAL = 6.694" 1.095 OAL = 5.462" 1.105 OAL = 6.353" 1.115 OAL = 6.058" 1.125 OAL = 3.163" 1.135 OAL = 8.303" 1.145 OAL = 9.407" 1.155 OAL = 9.088" Velocity Stats for 1.125" OAL Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted September 18, 2014 Share Posted September 18, 2014 J1480, are you finding that The Magic OAl (1.125") has decreased your group sizes from 6-9" down to 3"? I've never seen or heard of that magnitude of change before. I would expect 4" down to 3", but not such a large change. Link to comment Share on other sites More sharing options...
johnsons1480 Posted September 18, 2014 Share Posted September 18, 2014 J1480, are you finding that The Magic OAl (1.125") has decreased your group sizes from 6-9" down to 3"? I've never seen or heard of that magnitude of change before. I would expect 4" down to 3", but not such a large change. I did a similar test with Montana Gold about two years ago and didn't see such extreme variations. It was surprising to me how badly they shot at certain OALs, but they weren't random flyers. These were "groups" more or less, evenly distributed around the large box that became the max spread. The only way to take out the human in the equation is to repeat the test with a ransom rest. I don't have one of those, so I supported my forearms with sand bags and was able to hold very steady through the shot. I would be more than happy to repeat the test with a ransom rest if anyone is willing to loan one out Link to comment Share on other sites More sharing options...
Laughingdog Posted September 18, 2014 Share Posted September 18, 2014 One thing to bear in mind is that the case wall gets thicker as you get closer to the base. So if you load to 1.100" or shorter, you'll have more rounds not pass case gage/plunk test. With a long bullet, like the Bayou 147g 9mm, 1.130" is enough to start to see a significant increase in the number that fail. I have a CZ-75, so I have to load most bullets pretty short to not engage the rifling. The only exceptions I've found, so far, are the Berry's RN, Extreme RN, Golden Saber JHP, and the Bayou 124g RN. With those, I can load to 1.155" easily, and can load 1000 with maybe one or two failing the case gage. With something that requires me to load to 1.100" or shorter (Berry's FP, Bayou 135g, every other hollowpoint I've tried, every Blue Bullet, etc.), I'll have 3 or 4 fail out of every hundred. Link to comment Share on other sites More sharing options...
ToddKS Posted September 18, 2014 Share Posted September 18, 2014 I have seen dramatic changes in group size like that but it was with rifle loads. Did you try 1.120 and 1.130 to see if the data followed any trend line? That would be interesting to see. One thing appears clear, that barrel really did not like anything 1.135 or longer. Link to comment Share on other sites More sharing options...
johnsons1480 Posted September 18, 2014 Share Posted September 18, 2014 I have seen dramatic changes in group size like that but it was with rifle loads. Did you try 1.120 and 1.130 to see if the data followed any trend line? That would be interesting to see. One thing appears clear, that barrel really did not like anything 1.135 or longer. I did not. I decided that it wasn't worth my time to chase any additional accuracy gains. Also, I don't have a micrometer seater, so quite a few rounds were dumped into the practice bucket while trying to get the OAL right for this test. Link to comment Share on other sites More sharing options...
truborshooter Posted September 18, 2014 Share Posted September 18, 2014 Thanks for the reply on the data request I was hoping to see how performance was effected by oal always been told best accuracy is around 130-135 pf for 9mm I'm working on a steel challenge load and have noticed a significantly pronounced sweet spot but nothing like you got. Link to comment Share on other sites More sharing options...
johnsons1480 Posted September 18, 2014 Share Posted September 18, 2014 Thanks for the reply on the data request I was hoping to see how performance was effected by oal always been told best accuracy is around 130-135 pf for 9mm I'm working on a steel challenge load and have noticed a significantly pronounced sweet spot but nothing like you got. If that's the case, that would explain the very bad groups from 1.135-1.155. They averaged between 125-130 PF. Everything 1.125" and shorter averaged between 130 and 135 PF. Link to comment Share on other sites More sharing options...
seanc Posted September 18, 2014 Share Posted September 18, 2014 Unfortunately, I was using Chrono Log to document the velocities (terrific app btw), and I had to wipe my phone recently and lost all of the velocity data except for the load I ended up with. I can show you the group sizes at 25 yards and the screenshot of the one load I have though. I used Bayou Bullets 135 gr RN, Federal Cases, Federal Match SPP 10 Shot Group Sizes 1.085 OAL = 6.694" 1.095 OAL = 5.462" 1.105 OAL = 6.353" 1.115 OAL = 6.058" 1.125 OAL = 3.163" 1.135 OAL = 8.303" 1.145 OAL = 9.407" 1.155 OAL = 9.088" wow. I never would have guessed it would be this crazy, from 3" to 9", that is insane.... Link to comment Share on other sites More sharing options...
truborshooter Posted September 19, 2014 Share Posted September 19, 2014 Like I said, 'noticed a significantly pronounced sweet spot but nothing like you got' I went maybe 3/4" better groups at 25 yds, not 6" to 3". And that was confirmed with averaging 4-5 ten round groups pf, bullet jump are all elements but my interest was just oal variations and pressure. Link to comment Share on other sites More sharing options...
TheBoss Posted September 21, 2014 Share Posted September 21, 2014 Unfortunately, I was using Chrono Log to document the velocities (terrific app btw), and I had to wipe my phone recently and lost all of the velocity data except for the load I ended up with. I can show you the group sizes at 25 yards and the screenshot of the one load I have though. I used Bayou Bullets 135 gr RN, Federal Cases, Federal Match SPP 10 Shot Group Sizes 1.085 OAL = 6.694" 1.095 OAL = 5.462" 1.105 OAL = 6.353" 1.115 OAL = 6.058" 1.125 OAL = 3.163" 1.135 OAL = 8.303" 1.145 OAL = 9.407" 1.155 OAL = 9.088" Velocity Stats for 1.125" OAL Curious if varying the bullet weight given the exact load and OAL schedule would result in the same results. My thought is there is an optimal OAL for a given bullet weight given an identical load. Link to comment Share on other sites More sharing options...
johnsons1480 Posted September 21, 2014 Share Posted September 21, 2014 Curious if varying the bullet weight given the exact load and OAL schedule would result in the same results. My thought is there is an optimal OAL for a given bullet weight given an identical load. I'm not sure I'm following, can you restate that? Link to comment Share on other sites More sharing options...
jcc7x7 Posted September 27, 2014 Share Posted September 27, 2014 Always ?!?!? probably not Link to comment Share on other sites More sharing options...
tiberiumgold Posted September 28, 2014 Share Posted September 28, 2014 Curious regarding OAL, Typically is it true that if all other factors are equal the longer the oal the higher the power factor? Link to comment Share on other sites More sharing options...
kneelingatlas Posted September 28, 2014 Share Posted September 28, 2014 Curious regarding OAL, Typically is it true that if all other factors are equal the longer the oal the higher the power factor? Lower the PF. Longer OAL means more volume, less pressure, less velocity. That being said, powders do funny things once you just them out of their useful range... Link to comment Share on other sites More sharing options...
Joe D Posted September 28, 2014 Share Posted September 28, 2014 OTOH I load 9mm out to 1.200" with either a 160 gr lead bullet or a 160 gr Bear Creek moly. My RO likes that length. I pretty much use Solo 1000 in 9mm. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now