Jump to content
Brian Enos's Forums... Maku mozo!

TheBoss

Classified
  • Posts

    90
  • Joined

  • Last visited

Everything posted by TheBoss

  1. The mere fact that that you posted your question here says you've made up your mind and are looking for a reason to keep it in the safe. Your tone suggests you want to shoot it, so go have fun.
  2. Curious if varying the bullet weight given the exact load and OAL schedule would result in the same results. My thought is there is an optimal OAL for a given bullet weight given an identical load.
  3. Get a Glock 17/34, learn to shoot it while you learn what you want.
  4. 16" cut down a re crowned to 14.5" with a pinned and welded comp and mid length low profile adjustable gas block.
  5. It's worth it when you watch your muzzle velocity variance drops! #lovethatconsistentload
  6. ...because they are retards. I watched several race up to GM on classifiers, get a sponsor and then when it counts as the sponsor expects performance week in and week out, they fall flat typically landing at the bottom A shooters. Hard lesson.
  7. You can do a lot of the work yourself if you take your time, the get the STRS CZC will need it to do that work.
  8. CZC SP01s should come with the HAJO adjustable rear and go with the standard sight height, just pick your front sight width.
  9. TheBoss

    Tricked out CZs

    Without question CZ Custom. Angus and the guys have done more work on the CZ platform than anyone else by a wide margin. I have 2 CZ SP01 Shadow Target Custom with STRS and the 85 trigger with a competition trigger. I have also purchased the Accu upper and have ordered New AccuShadow with identical set up to my SP01. I also shoot Production in USPSA. I say all this because I would not put this much money into a single platform if it did not perform!
  10. Ben Stoeger's Boss hanger, BladeTech DOH, http://www.benstoegerproshop.com/BSPS-BOSS-DOH-Holster-Systems-p/bsps-holster.htm Mec-Gar 17 http://www.mec-gar.com/Magazines/CZ/MGCZ7517(19 will not fit in the Production Box) CZ Customs SRTS http://czcustom.com/cz75disconnectorshrt.aspx
  11. TheBoss

    CZ

    4.1GR TiteGroup 124 Montana Gold RN 1.085, excellent results.
  12. TheBoss

    Annual Maintenance

    CZC SP01 Shadow for competition
  13. TheBoss

    Annual Maintenance

    What does CZC recommend replacing during its annual? I.e. Recoil spring 11#?, trigger return spring, slide stop,etc...
  14. TheBoss

    Test

    Testing new Tapatalk posting
  15. Sent from my iPad using Tapatalk HD
  16. Yep. There you go. I was working with factory loads that were loaded at 1.125; thus the mag fix versus a longer load. My guess is the casing is catching on the mag. Sent from my iPad using Tapatalk HD
  17. I had several issues similar to your problem. Try the following: 1.Take apart the extractor and clean it out - if there is dirt causing the casing to sit cock eyed there will be an off center hit from the firing pin on the primer of a spent casing 2. Determine if the the short OAL is causing the casing to catch on the top front edge of the mag (standard OAL for S&W 40 is 1.130) and creating the jam - I scalloped the front of my mag to keep the casing from catching before the bullet impacts the feed ramp Sent from my iPad using Tapatalk HD
  18. TheBoss

    Fiocchi 124GR 9MM

    @Jeff9mmM&P are you running the factory striker spring or a reduced power spring? I am running a reduced power hammer spring on my CZ and hard primers can create lite strikes. Considering the ammo issues lately, I am looking for something else I can shoot until the military finishes its buying spree on ammo. Sent from my iPad using Tapatalk HD
  19. TheBoss

    Fiocchi 124GR 9MM

    Anyone shoot Fiocchi 124GR in a CZ SP01 Shadow with a competition trigger job? I want to know if the Fiocchi primers are hard or soft primers. Sent from my iPad using Tapatalk HD
  20. Killer! Nice job! Sent from my iPad using Tapatalk HD
  21. Roflmao! Clear my stoppage! Sent from my iPad using Tapatalk HD
  22. I emailed Costa this morning on the website with my invoice number and commented on the issue here, asking them not to send any replacement. By lunch they reversed the charge on my credit card. Customer Service was great. They have a good idea with the extended mag release, but poor materials and manufacturing execution. Sent from my iPad using Tapatalk HD
×
×
  • Create New...