RobE1010 Posted November 8, 2013 Share Posted November 8, 2013 I am looking for any recommendations for 9mm Minor load recipes for use in USPSA Production, IDPA as well as Steel Challenge for both a Glock 34 and M&P 9L/Pro. I am looking for loads using TiteGroup powder as that's what I have on hand and prefer to use. Ideally I'd be looking for loads using 115gr, 124gr and 147gr projectiles and your current OAL. Thanks in advance for any help! Link to comment Share on other sites More sharing options...
rangerguy Posted November 9, 2013 Share Posted November 9, 2013 I run 4.4 Titegroup 124 CMJ MG. 1.125 oal Link to comment Share on other sites More sharing options...
DavidG34 Posted November 9, 2013 Share Posted November 9, 2013 4.0 tightgroup 124 fmj at 1.145 out of a G34 makes PF all day long. Link to comment Share on other sites More sharing options...
Buildit2 Posted November 9, 2013 Share Posted November 9, 2013 I've used 4.6 gr titegroup with 115 gr berrys JRN bullets and a COL of 1.150 + .005 to get 1100fps + 30 fps but that is with a G17. At 5.0 grains I was seeing 1250 fps with the G17 just for reference. I don't have results with this load for my G34 gen4. Sorry, but I hope this helps. Link to comment Share on other sites More sharing options...
45 Raven Posted November 9, 2013 Share Posted November 9, 2013 4.0 TiteGroup over 124 gr.Montana Gold JHP @ 1.140 COAL = 1965 FPS/132 PF from Glock G34 Link to comment Share on other sites More sharing options...
jcc7x7 Posted November 9, 2013 Share Posted November 9, 2013 4.0 TG 125 MT Gold or Horn. HAP makes Pf in my 1911's, sig 226 and glock 17. I used to change oal for each pistol now I load them all for the the shortest gun. i.e. the glock needs 1.065 to run so now they all get it so I don't have to change things. But figure out what OAL your gun needs and go from there. the longer the OAL usually the more powder required. we're talking tenths of grains Link to comment Share on other sites More sharing options...
Lowleft Posted November 9, 2013 Share Posted November 9, 2013 Glock 34 Berry's 124 RN 3.9 titegroup 130 PF 147 RN 3.2 titegroup 130 PF Both loads at 1.150 COL I go up .1 grns for jackets bullets. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
uod Posted November 12, 2013 Share Posted November 12, 2013 (edited) 4.0 Titegroup out of the stock G34 barrel at a 1.135 OAL will make minor. Chrono usually gets me at about 132PF with this . I am running Montana Gold 124gr. JHPs. Edited November 12, 2013 by uod Link to comment Share on other sites More sharing options...
Butterpuc Posted November 12, 2013 Share Posted November 12, 2013 3.2 Titegroup with 147 FMJ/JHP at 1.135" Link to comment Share on other sites More sharing options...
ninemmbill Posted November 12, 2013 Share Posted November 12, 2013 Glock 34 Berry's 124 RN Titegroup 4.0 1.140 OAL Link to comment Share on other sites More sharing options...
45 Raven Posted November 13, 2013 Share Posted November 13, 2013 Just noticed that my earlier post (#5 in this thread) shows a MV of 1965 FPS. That just a bit over-stated! Actual MV is 1065 FPS! Sorry for the typo! Link to comment Share on other sites More sharing options...
grapemeister Posted November 13, 2013 Share Posted November 13, 2013 Just noticed that my earlier post (#5 in this thread) shows a MV of 1965 FPS. That just a bit over-stated! Actual MV is 1065 FPS! Sorry for the typo! I was wondering about that! I was thinking, wow, that's got to hurt. Link to comment Share on other sites More sharing options...
rowdyb Posted November 13, 2013 Share Posted November 13, 2013 glock 34 with barsto barrel. 3.2 of titegroup. 147 round nose copper plated from extreme, 1.150 oal. Link to comment Share on other sites More sharing options...
Rokihsa Posted November 13, 2013 Share Posted November 13, 2013 3.1 Titegroup with 147 Bayou Bullet at 1.135 Glock 34 Link to comment Share on other sites More sharing options...
jeremy kemlo Posted November 13, 2013 Share Posted November 13, 2013 3.1 TG, 147 bayou, 1.15oal shoots great out of glock 34 and 5''' m&p pro Link to comment Share on other sites More sharing options...
Snapple Posted December 9, 2013 Share Posted December 9, 2013 3.2 Titegroup 147 Extreme 1.155 col 130pf Link to comment Share on other sites More sharing options...
earthshine402 Posted December 9, 2013 Share Posted December 9, 2013 I've loaded thousands of this load: 3.1 Titegroup 147gr Zero JHP 1.110 OAL 132 PF out of a G34 Link to comment Share on other sites More sharing options...
millisec Posted December 20, 2013 Share Posted December 20, 2013 Basically found this load here and been using it for 3+ years out of M&P Pro 5" 4.0 Titegroup 124g Zero FMJ 1.15 OAL Win SPP Just got 4k FMJ 147g Zero's last week and going to probably run 3.2gr titegroup same OAL. Link to comment Share on other sites More sharing options...
Red Ryder Posted December 21, 2013 Share Posted December 21, 2013 In my experience with Titepoop, I had to use 4.2 to 4.3 grains with 124 gr MG CMJ and get to PF up to 135+ for acceptable accuracy in my XDM 4.5 and a G17. 128 to 132 PF produced 4-5 inch groups off a sandbag at 20 yards. 135+ PF tightened the group up to 2 inches. I found Titepoop to be hot, snappy, and, dirty. BUT powder supplies are TiGHT and I would buy some if any shop had some. Link to comment Share on other sites More sharing options...
Lemmy Posted May 8, 2014 Share Posted May 8, 2014 4.5 grains of Tightgroup with 115 grain FMJ, OAL 1.100, pushes 1150 fps. Best Accuracy is 4.2 @1100 fps. 4.5 probably maxes SAAMI pressures 4.5 is a maximum load so use caution! Link to comment Share on other sites More sharing options...
Poseidon215 Posted May 8, 2014 Share Posted May 8, 2014 147gr bayou over 3.0 TG @ 1.155 makes 140pf out of my XDm 5.25 Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
texasref Posted May 8, 2014 Share Posted May 8, 2014 147 grn over 3.2 with OAL of 1.160. 135 pf from 4.5" barrel. Link to comment Share on other sites More sharing options...
Mespo Posted May 8, 2014 Share Posted May 8, 2014 3.3 TiteGroup 135 Bayou 1.10 oal CZ SP-01 Shadow 130 PF all day long.... Link to comment Share on other sites More sharing options...
Balakay Posted December 13, 2014 Share Posted December 13, 2014 I saw this data on the Hodgdon website. I have already contacted them for verification but I have not heard back yet. Unlikely to make Minor but I am curious. Anyone using such a low powder charge?? 2.8 Titegroup (Max 3.2) 125 Hornady HAP 1.069" COL Link to comment Share on other sites More sharing options...
ActionJackson Posted December 15, 2014 Share Posted December 15, 2014 (edited) I've done a lot of testing with a G34 in a Ransom Rest. I bought a Ransom and set about finding the most accurate polymer coated loads using the cheapest available powder, Alliant Promo (same as Red Dot by weight). I've also experimented with several other fast powders (TiteGroup, Green Dot, Clay Dot, e3, WST), but didn't find them to be more accurate than Promo with polymer coated bullets. Here are my top three recommendations for loads with Promo. I know you asked for TiteGroup, but I thought you might find this useful since you were looking for G34 data. They all make minor. All groups are ten-shot strings and were tested from a Ransom Rest at 50 feet. SNS 147 1.155 3 grains .378 1.4'' TBB 147 1.13 2.8 grains .379 1.4'' Bayou 147 1.16 3 grains .378 1.5'' Edited December 15, 2014 by ActionJackson Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now