jeremy kemlo

What do you think about your magwell (techwells) vs the Taylor freelance?

What height mount did you get on your 507 comp

Oops. holosun aems

Anyone try the holosun AESM with the riser? How would that compare to the 510 C or 507 comp?

I’m fairly new to PCC. Seems like there’d be some benifit to having the dot close to the bore for parallax, but a higher riser would definitely feel much more natural. Which one do you think has the biggest advantage? Which riser heights do you like the best? do you know the height of that compares to the 510 C in its stock configuration ?

Looking for a Magwell for My jp5. Taylor freelance, Texhwell, or ?

Jp5 on the way and it will need a dot. I have a 510 C on my AR and it’s not bad. Was debating on getting the 507 comp. I think the comp may need a riser. Anyone know which one Max Leograndis is running? I also have a little vortex venom. I was thinking about throwing on a 45° mount which one of those mounts should I look at?

Just got an mpx that has a hiperfire trigger. The hammer has a 4 on it. Curved trigger. Which trigger is this?

I could not tell any difference.

The Glock magazine adapter is tapered in towards the top front side of the magazine. It follows the contours of the Glock magazine. MBX magazine even though it is a Glock magazine does not taper at the top like a he Glock mag. 60 seconds, with a file and the MBX magazine fits perfectly. Runs great.

Ruger PCC set up with Glock Mag adapter. Glock magazines work perfectly fine, but the metal mag latch was wearing away the corner edge of the Mag. Wanted to switch to a metal magazine. I purchased an MBX steel Glock magazine. It does not slide all the way up into my Ruger PCC. Works fine in my Glock but not in my Ruger PCC. Anyone have a similar issue that they found a fix for?

Has anyone use the Tandemkross or M Carbo bolt buffer? I have one sitting on my bench, but I’ve not installed it yet. I taped the buffer directly to the back of the bolt and then dropped it several inches onto the concrete floor. The M carbo buffer bounces back considerably more than the stock buffer. That energy is going to make the bolt go forward faster than the stock bolt. It’s like dropping the bolt onto a hard piece of plastic (stock)versus a thin rubber bouncy ball. (Mcarbe) for those of you who have tried the M carbo buffer does it help, does it do nothing except maybe change a little of the noise, or does the bolt going forward faster make it worse?

What is the difference shooting 145 Gr bullets vs 160 at 125-130 power factor out of a 929. My press is set up to do 145 for my semi auto so I could just adjust the powder amount. Unless there is an advantage to the 160.

Shooting the WRC this weekend with my 14 year old daughter. My daughter wants to shoot the 929 and I do not have any load data for it. I have a couple options. I could bring Factory 115 grain federal ammunition. not sure what power factor that would result in. Or I could load something up with my 145 Gr Bayou Bullets within 320. I used 145 grain Bayou Bullets with 3.2 g of N320 in my Cz Shadow 2. That gets me 131 power factor but not sure what that will do in the 929. Any help would be greatly appreciated.

Am I going k to load the 160 to a length of 1.125. That’s what my press is at now.

I got some 160 bayou bullet. from what I have read it looks like 2.8 of N320 should do the trick. Any thoughts?

Shooting the WRC this weekend with my 14 year old daughter. My daughter wants to shoot the 929 and I do not have any load data for it. I have a couple options. I could bring Factory 115 grain federal ammunition. not sure what power factor that would result in. Or I could load something up with my 145 Gr Bayou Bullets within 320. I used 145 grain Bayou Bullets with 3.2 g of N320 in my Cz Shadow 2. That gets me 131 power factor but not sure what that will do in the 929. Any help would be greatly appreciated.

I I should be good for weight. I can use factory base pads if others are too big. just need some new mag pouches and holster.

Will this work in any of the categories ?

My shadow 2 is set up for carry optics in USPSA. Slide was cut by cz custom for their optics plate and I run an sro. The slide was also cut by cz custom when you needed to make weight for USPSA. Single slot cut on top of the slide behind the front sight. Lok Light weight palm swell grips. Can’t use my USPSA mags but can I use stock mags with slightly bigger base pads. Adds know rounds.

thanks

Does anyone make a mounting plate so I can put my holosun 510C on my Smith & Wesson 627?

Pro grip

Sorry, option for where to get it done. This is an internal relief cut to prevent the frame from cracking with high round count. New fames all have this relief cut.

Thanks