czambesi Posted June 10, 2012 Share Posted June 10, 2012 I am new to reloading and currently have a single stage I am going to start loading rifle on (bolt not in large quantities). I was planning on using the single stage to re-size all the brass I have (hand gun and rifle). Anyone recommend a solid resizing die? (Will be buying .40, 9mm, .38 & .45) Thanks. Chris Link to comment Share on other sites More sharing options...
chirpy Posted June 10, 2012 Share Posted June 10, 2012 (edited) I don't believe you can go wrong with any of the manufacturers die sets. I prefer RCBS but that is JMHO. You might need a U (undersize) die for .40. Do a search for info on that. Richard PS: Guess I should add that I would recommend getting a die set w/carbide resizer. Edited June 10, 2012 by chirpy Link to comment Share on other sites More sharing options...
czambesi Posted June 11, 2012 Author Share Posted June 11, 2012 Thanks for the info, I am looking at some EGW dies for now just to resize the brass. They have some U dies. Thanks, Chris Link to comment Share on other sites More sharing options...
MARKAVELI Posted June 13, 2012 Share Posted June 13, 2012 (edited) My Dillon dies work great but if I get picky and wonna bust that "bulge"? Redding carbide GR-X sizing die for my .40 on a single stage (since you got the single stage already) oh RCBS full length sizer for my 223 everything else DILLON! Why spend the money for a more exspensive die if a less exspensive die can do the same for less. . Good luck.. Edited June 15, 2012 by MARKAVELI Link to comment Share on other sites More sharing options...
Mitch Harrington Posted June 13, 2012 Share Posted June 13, 2012 I use the EGW U-die in most every caliber I load. Link to comment Share on other sites More sharing options...
czambesi Posted June 14, 2012 Author Share Posted June 14, 2012 Thanks for the info guys Link to comment Share on other sites More sharing options...
Recoil45 Posted June 14, 2012 Share Posted June 14, 2012 I pretty much use Lee dies for everything. I was on a budget when I got started and they were the cheapest. While I have upgrade almost everything else, I never found a reason to replace my dies. Link to comment Share on other sites More sharing options...
Bob DuBois Posted June 14, 2012 Share Posted June 14, 2012 Take a look at the Lee Carbide four die set, Cheap and they have one of the best designs on their sizer. Sizes closer to the extractor groove eliminating the buldge and primer punch works great. That's what I use on my 650 and 550 machines. When you get the funds look hard at a 550, you'll never look back once you get used to a progressive. Link to comment Share on other sites More sharing options...
mike l m Posted June 14, 2012 Share Posted June 14, 2012 Hey Guys, I have been reloading for 30 plus years and found Lee has a great oversized die for 9mm, 40 and 45 acp. These dies work great in my OLD 450B's. So yes I agree use a carbide oversized die for sizing all cases. It will help with loading and at the range. Sometimes you may find some 9mm cases from a Glock that have a bulge near the base of the case, these dies remove that bulge. Also get a case gauge and use it all the time after you reload. Drop in drop out. Like go, no go. Mike Link to comment Share on other sites More sharing options...
98sr20ve Posted June 14, 2012 Share Posted June 14, 2012 Regular Lee sizing die is best. I never found the need for a U-die in any caliber other then .380. For some reason .380 has some thinner brass and Jacketed bullets don't have as much tension. 9mm, .40 never a issue. All fit a case gauge perfectly after sizing. I don't like over sizing all brass just because I can. That is what a U-Die is doing if you use it and don't need it. Link to comment Share on other sites More sharing options...
czambesi Posted June 14, 2012 Author Share Posted June 14, 2012 Thank you all for the information! Helps greatly!! Thanks, Chris Link to comment Share on other sites More sharing options...
bigfish Posted June 15, 2012 Share Posted June 15, 2012 I would def. get a egw U-die for the .40 s&w. Seems to do a better job on the cases with a "Glock bulge". Never never had any issues with standard Lee dies in any of my other calibers. Link to comment Share on other sites More sharing options...
Lonnie Posted June 16, 2012 Share Posted June 16, 2012 Take a look at the Lee Carbide four die set, Cheap and they have one of the best designs on their sizer. Sizes closer to the extractor groove eliminating the buldge and primer punch works great. That's what I use on my 650 and 550 machines. When you get the funds look hard at a 550, you'll never look back once you get used to a progressive. I also agree with every bit of this. Link to comment Share on other sites More sharing options...
saibot Posted June 16, 2012 Share Posted June 16, 2012 I have found the Lee dies to be an outstanding value across all my presses and calibers. I use them for 9mm, .223, and .308. For precision 308 I use a Lee collet neck sizer have found nothing better. I played with the RCBS X-sizer in .223 but still prefer the Lee. The one issue I had on my 650 was the Lee 9mm sizer didn't seem to have enough threads for the lock ring once it was in the tool head. Had to use a Dillon which works well but I have to stock the little C clips that tend to break every 5-10k cases sized. Any of you have the same problem with the Lee being too short? Link to comment Share on other sites More sharing options...
98sr20ve Posted June 17, 2012 Share Posted June 17, 2012 I have found the Lee dies to be an outstanding value across all my presses and calibers. I use them for 9mm, .223, and .308. For precision 308 I use a Lee collet neck sizer have found nothing better. I played with the RCBS X-sizer in .223 but still prefer the Lee. The one issue I had on my 650 was the Lee 9mm sizer didn't seem to have enough threads for the lock ring once it was in the tool head. Had to use a Dillon which works well but I have to stock the little C clips that tend to break every 5-10k cases sized. Any of you have the same problem with the Lee being too short? You can use the Dillon lock rings on the bottom of the die under the tool head. I Lee on my Dillons. Never a issue. You don't need a lot of threads to lock it down. Flip the Lee lock rings upside down. Link to comment Share on other sites More sharing options...
saibot Posted June 17, 2012 Share Posted June 17, 2012 I have found the Lee dies to be an outstanding value across all my presses and calibers. I use them for 9mm, .223, and .308. For precision 308 I use a Lee collet neck sizer have found nothing better. I played with the RCBS X-sizer in .223 but still prefer the Lee. The one issue I had on my 650 was the Lee 9mm sizer didn't seem to have enough threads for the lock ring once it was in the tool head. Had to use a Dillon which works well but I have to stock the little C clips that tend to break every 5-10k cases sized. Any of you have the same problem with the Lee being too short? You can use the Dillon lock rings on the bottom of the die under the tool head. I Lee on my Dillons. Never a issue. You don't need a lot of threads to lock it down. Flip the Lee lock rings upside down. I never thought of that! Great idea. Thanks for the tip. Link to comment Share on other sites More sharing options...
czambesi Posted June 18, 2012 Author Share Posted June 18, 2012 Thanks again for all the info. Ordering a couply dies next pay to get the brass going Thanks, Chris Link to comment Share on other sites More sharing options...
farmrboy Posted August 29, 2012 Share Posted August 29, 2012 Lee makes a push through die called the bulge buster. I have it for .40, don't know if it comes in any other calibers. It has a post the mounts on the ram to push the cases or finished ammo through the die. The top of the die box mounts on top of the die to act like a hopper to hold the cases as they get pushed through the die. I shoot a Tanfoglio, they can be very finicky about the ammo they get fed. This guarantees no problems. Link to comment Share on other sites More sharing options...
g mac Posted August 29, 2012 Share Posted August 29, 2012 Any brand of reloading dies for rifle works. I had used RCBS, Lee, and Hornady dies on RCBS single stage press loading .223, 6.8spc, .243, .450 bushmaster, .308, .30 carbine, 7.62x39, .270, etc. with no problems. I like the hornady dies with bullet guide sleeve (it guides the bullet in place when seating). To me, single stage is better for making accurate loads for accuracy, but for volume/plinking shooting, progressive is the way to go. The most important thing is to size your brass as far/deep as the maximum the sizing dies would allow, and also trimming the brass to the correct size. Good luck! Link to comment Share on other sites More sharing options...
rooster mcbee Posted August 29, 2012 Share Posted August 29, 2012 +1 for the Lee dies. I was told a long time ago that Lee made the best sizers. I bought one for each pistol caliber I load and have never looked back. I have a lot of faith in Redding dies for my rifle needs, and I suspect that their pistol dies would be the same high quality, but they would cost a lot more, and I doubt they would be better for sizing than Lee. Link to comment Share on other sites More sharing options...
Norther Posted August 30, 2012 Share Posted August 30, 2012 I have Lee, Hornady, RCBS, Redding, and Dillon dies. My current favorites are the Redding and Dillon. I usually replace the lockrings with Hornady lockrings (for single stage) because the locking screw doesn't tighten against the threads (the Lees don't even lock to the die at all). The only serious issues I've had are a Lee .458 SOCOM size die that frequently seized cases (even with good lube and after 1 trip back to the factory for hand polishing), a Dillon 9mm seating die (actually, the seater plug shape) that for some reason wouldn't work with the 115 gr Montana Gold JHPs I was using, and a .380 Hornady seater that has no provision for taper crimping. Link to comment Share on other sites More sharing options...
Poppa Bear Posted August 30, 2012 Share Posted August 30, 2012 What is the best sizing die? The one that works!!! Is your chamber loose? (This is 5 or 6 thousandths larger than SAAMI specs for a cartridge) Most any die works... Is the chamber real tight? (We are talking 2 to 3 thousandths larger than SAAMI specs) You will need to use something like the U die, Redding Competition, or a push through die. The important part about sizing the brass is not what it does at the mouth, most any die works there, it is what it does to the base of the case. Failing to properly size the base is what causes most jams that lock the gun up. Link to comment Share on other sites More sharing options...
forddriver Posted August 30, 2012 Share Posted August 30, 2012 (edited) I will add another +1 for Lee dies. I like the 4 carbide die pistol with the Factory Crimp personaly. Edited August 30, 2012 by forddriver Link to comment Share on other sites More sharing options...
elroyyboy Posted September 14, 2012 Share Posted September 14, 2012 Not to hijack the thread, but I can't find info on the "bulge buster" that indicates if it can be used with anything but the FCD. Can it be used with my Lee 3 Die set(which did not include FCD) that came with my Pro 1000? Does it replace bullet seater in crimp die, or decapper in sizing die? Thanks, Link to comment Share on other sites More sharing options...
dragon52 Posted September 14, 2012 Share Posted September 14, 2012 Sorry but the lee dies suck. Rcbs hornady and redding are my choice. I have been reloading for 30+ years and do not like lee dies. Just my my personal opion. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now