BritinUSA Posted December 14, 2017 Share Posted December 14, 2017 Thats what I am running; I use the grams springs too, the only other thing you will need is a small round file or dremel to cut out part of the follower to stop it hitting the internal slide release. Link to comment Share on other sites More sharing options...
saibot Posted December 14, 2017 Share Posted December 14, 2017 1 minute ago, BritinUSA said: Thats what I am running; I use the grams springs too, the only other thing you will need is a small round file or dremel to cut out part of the follower to stop it hitting the internal slide release. What's the difference between doing that and using they Springer or Taylor extended mags? Seems like extra steps to make the TT's work. Link to comment Share on other sites More sharing options...
BritinUSA Posted December 14, 2017 Share Posted December 14, 2017 If you want the highest capacity then you will need to change the followers, plus you will need different springs due to the increased length of the magazine. This applies to any extended base pad. Link to comment Share on other sites More sharing options...
DKorn Posted December 14, 2017 Share Posted December 14, 2017 2 hours ago, BritinUSA said: If you want the highest capacity then you will need to change the followers, plus you will need different springs due to the increased length of the magazine. This applies to any extended base pad. Are the Taran Tactical pads with Grams followers the highest (reliable) capacity for a 140 mm mag? Link to comment Share on other sites More sharing options...
saibot Posted December 14, 2017 Share Posted December 14, 2017 Since this thread is massive at this point, may I ask you guys to start a new thread specificity discussing hi cap mag options for the Q5? It’ll be so much easier for people to find and update. /2cents. Link to comment Share on other sites More sharing options...
BritinUSA Posted December 14, 2017 Share Posted December 14, 2017 10 minutes ago, DKorn said: Are the Taran Tactical pads with Grams followers the highest (reliable) capacity for a 140 mm mag? Reliable with 22 +1 Link to comment Share on other sites More sharing options...
MemphisMechanic Posted December 14, 2017 Share Posted December 14, 2017 (edited) 2 hours ago, BritinUSA said: Reliable with 22 +1 23 + 1 actually. Never failed to function when barney’d up all the way. TTI pad. Grams follower and spring for the P-320, with the tab that locks the slide open ground off. (I usually load them to 23 then strip a round out at LAMR for 22+1, unless there’s some reason the extra round or two will be a serious advantage.) Edited December 14, 2017 by MemphisMechanic Link to comment Share on other sites More sharing options...
Single Stack Posted December 15, 2017 Share Posted December 15, 2017 I am only getting 20+1 with the same setup so I'll need to see if the grams follower is binding up where the mag and TTI pad interface. Might need to trim the follower slightly to clear. Link to comment Share on other sites More sharing options...
Bluescholar Posted December 23, 2017 Share Posted December 23, 2017 I have to press down extra hard once it hits around 20, and then it will give, allowing me to stack in a few more rounds. I would say that the interface seems iffy for me as well. Does anybody have problems with the TT basepads allowing the magazines to go up too far and hit the ejector? I've had to bend my ejector back before. Link to comment Share on other sites More sharing options...
MemphisMechanic Posted December 26, 2017 Share Posted December 26, 2017 (edited) @Bluescholar I haven’t. But I also don’t hammer my mags into the gun and I have not shot it with the extended mags a ton. It sees far more use in Production. Edited December 26, 2017 by MemphisMechanic Link to comment Share on other sites More sharing options...
jaep1911 Posted December 26, 2017 Share Posted December 26, 2017 On 12/23/2017 at 12:08 AM, Bluescholar said: I have to press down extra hard once it hits around 20, and then it will give, allowing me to stack in a few more rounds. I would say that the interface seems iffy for me as well. Does anybody have problems with the TT basepads allowing the magazines to go up too far and hit the ejector? I've had to bend my ejector back before. Just checked out mine with an empty mag and a piece of copy paper. With the mag fully pushed in, there is a gap between the lip and the ejector as I can slide the paper in and outta gap with no binding. My ejector is not bent. Link to comment Share on other sites More sharing options...
mstamper Posted December 26, 2017 Share Posted December 26, 2017 On 11/30/2017 at 2:08 PM, saibot said: I'm using a Blade-Tech on a BOSS hanger and it's fine. I originally ordered a Comp-Tac since I really liked the Sig one I've used for a couple of years, but it must have been a lemon because it didn't fit and I had to return it. I use the GHOST "the thunder" holster with their hanger. Select the P99 holster as the Q5 frame is the same. Link to comment Share on other sites More sharing options...
Bluescholar Posted December 28, 2017 Share Posted December 28, 2017 Thanks to MemphisManiac and Jaep1911. I must have a faulty set. Just to clarify, the q5 is good to use with extended 140mm baseplates in carry optics division, correct? Link to comment Share on other sites More sharing options...
BritinUSA Posted December 28, 2017 Share Posted December 28, 2017 Yes Link to comment Share on other sites More sharing options...
johes Posted December 31, 2017 Share Posted December 31, 2017 Will the Q5 fit the IDPAbox with the 17rd mags ? Link to comment Share on other sites More sharing options...
sundevil827 Posted January 9, 2018 Share Posted January 9, 2018 I'm having the same mag issue trying to set-up the Taran pads with the Gram's spring and 320 follower. I've used the dremel to remove the tab, but I hit a hard 19 rounds and that's it. With the Taylor's, it's 21. Odds are missing some more plastic on the follower? Link to comment Share on other sites More sharing options...
MemphisMechanic Posted January 9, 2018 Share Posted January 9, 2018 (edited) @sundevil827 I did taper the top & bottom of all 4 corners of my followers inward slightly, when I first put them together. Just a quick blip with the dremel. So that they’ll make the transition from tube to mag extension smoothly. I guess it worked, if mine have always been flawless and yours haven’t. Edited January 9, 2018 by MemphisMechanic Link to comment Share on other sites More sharing options...
PokerNGuns Posted January 10, 2018 Share Posted January 10, 2018 (edited) On 9/5/2017 at 10:39 AM, MemphisMechanic said: Didn't like how shallow the sight picture is. I ordered the Dawson's for the regular PPQ and discovered that the LPA rear has a unique dovetail and they wouldn't work. Dawson sight picture: Soooo I made another trip over to my buddy's house, and milled .030" out of the bottom of the notch. I'll be running this with a .190-.195 Dawson front when I'm not shooting carry optics. Note the two ledges in the bottom of the rear notch: Annnnd gone: Could you have gone lower than this without damaging the sight? If it's not too much trouble I'd like to see an after picture looking through. Thanks. Edited January 10, 2018 by PokerNGuns Link to comment Share on other sites More sharing options...
MemphisMechanic Posted January 10, 2018 Share Posted January 10, 2018 (edited) @PokerNGuns... No point in milling more deeply: I’m pretty much flush with the head of the elevation adjustment screw now - you’re pretty much looking across the head of it. It’d be a few days before I took another photo, and I’m not sure how much more you’d see. Put a gun underneath that first photo, and that’s exactly what you look at when shooting. I took the image arms-length from the back of the slide then cropped in to enlarge it. It’s exactly “to scale.” Edited January 10, 2018 by MemphisMechanic Link to comment Share on other sites More sharing options...
sundevil827 Posted January 12, 2018 Share Posted January 12, 2018 That may be it.... I tried it with a couple of followers, and it's 19, so I assume right where it's going into the extension. I was worried about taking off too much material. Link to comment Share on other sites More sharing options...
sundevil827 Posted January 12, 2018 Share Posted January 12, 2018 I'll try the taper, I suspect that's gotta be it. Thanks Link to comment Share on other sites More sharing options...
BritinUSA Posted January 12, 2018 Share Posted January 12, 2018 I did not need to taper the follower. Just a small cut away to clear the magazine release, then bent up the last coil of the spring so it sits flat inside the base pad. Link to comment Share on other sites More sharing options...
mantus Posted February 17, 2018 Share Posted February 17, 2018 A question to the reloaders: Can someone give me a suggestion for COL 9mm for Q5 123gr. RN HP like this one: Link to comment Share on other sites More sharing options...
saibot Posted February 17, 2018 Share Posted February 17, 2018 2 hours ago, mantus said: A question to the reloaders: Can someone give me a suggestion for COL 9mm for Q5 123gr. RN HP like this one: It really depends on the ogive of the particular bullet, but I've found that just about anything will chamber on the Q5 at 1.10. You can seat a dummy long and drop it into the chamber to see at which point it no longer touches the chamber. Or just seat at 1.10. ;) Link to comment Share on other sites More sharing options...
mantus Posted February 17, 2018 Share Posted February 17, 2018 1 minute ago, saibot said: It really depends on the ogive of the particular bullet, but I've found that just about anything will chamber on the Q5 at 1.10. You can seat a dummy long and drop it into the chamber to see at which point it no longer touches the chamber. Or just seat at 1.10. Interesting, I do all FMJ/CMJ RN at 1.10 with no issues, but by the book as far as I can remember the FN should just a little bit less. I will gust give it a try at 1.10 an if any issues I will go play a bit Thank you. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now