m1agirl Posted November 4, 2014 Share Posted November 4, 2014 I've had an issue for awhile with my mags not wanting to drop free, which is a pain when running a match and having to pull your mag out to reload. I have this issue with every mag, including my new 10 rounder. Any advice on how to fix this problem? Thanks Link to comment Share on other sites More sharing options...
KOBGT Posted November 4, 2014 Share Posted November 4, 2014 I have same problem. Haven't found a solution yet Link to comment Share on other sites More sharing options...
Neomet Posted November 4, 2014 Share Posted November 4, 2014 CZC basepads? Take the basepad off the mags and see if they drop free. If not, pull the grip panels off and see if that does the trick. That may give you a direction to go. Link to comment Share on other sites More sharing options...
KOBGT Posted November 4, 2014 Share Posted November 4, 2014 Tried all that Link to comment Share on other sites More sharing options...
Neomet Posted November 4, 2014 Share Posted November 4, 2014 Hmmm... Does it insert easily? Link to comment Share on other sites More sharing options...
KOBGT Posted November 4, 2014 Share Posted November 4, 2014 Nope Link to comment Share on other sites More sharing options...
CZ85Combat Posted November 4, 2014 Share Posted November 4, 2014 where is it rubbing? Link to comment Share on other sites More sharing options...
alma Posted November 4, 2014 Share Posted November 4, 2014 Which magwell? I have to remove material from both magwell and basepads Link to comment Share on other sites More sharing options...
huskerlrrp Posted November 4, 2014 Share Posted November 4, 2014 It could also be your mag brake or button. Try removing your mag brake and see if it happens. As far as the button, I've had to remove some material because I would press too hard and the back side of the button would press against the magazine. Link to comment Share on other sites More sharing options...
leas327 Posted November 4, 2014 Share Posted November 4, 2014 I have no experience with 10 rounders but my full capacity mags have gone from drop free to not so drop free over time. It was never an issue with the mag brake for me. My mags just got out of spec over time. My mags tend to get wider at the mag catch hole and that is what caused them to not drop free. The two most extreme/finiky mags would measure .870 X 1.275 in the area of the mag catch hole. The other was .868 x 1.272. My other six mags would be somewhere in between those dimensions. I resized my mags in a vise with non marring jaws. Usually the smaller measurement was around .876 before I squeesed on it. The more you squeeze to make one dimension smaller, the bigger you will make the other one. It takes a little trial and error to find what works for each tube. Link to comment Share on other sites More sharing options...
m1agirl Posted November 4, 2014 Author Share Posted November 4, 2014 I have this problem with hi cap mags and the 10 rounder. If i remember correctly, I've only had one mag actually work and now none work. I've thought about trying to add some sort of weight to the bottom of the mag to see if that would work, but I'm not sure. Mine are stock setup, haven't done anything to them. I have different grips, and I've tried with no grips and they still won't drop. I've also taken out the mag break and have had no luck. Has anybody tried the flatter mag break from cz custom, and had luck with it? Link to comment Share on other sites More sharing options...
bigdave24 Posted November 4, 2014 Share Posted November 4, 2014 I had some 10 round .40 mags that wouldn't drop free. In fact one of them I had to take the grips off to remove. I believe they were out of spec. as other mags worked fine. Link to comment Share on other sites More sharing options...
zzt Posted November 5, 2014 Share Posted November 5, 2014 I had the same problem with the factory followers. As they get older they have a tendency to cock to one side. Mine cock so that the high side is even higher. Once they get high enough, the mag will not drop free when empty. However, it will drop free if there is still a round in it. So it is definitely a follower problem. Changing the spring and follower to the CZC unit with 10-coil spring solves the problem. All my mags have the CZC extended base pad. I'm not sure if that spring will work in the 17 round mags. Link to comment Share on other sites More sharing options...
W_Buck Posted November 5, 2014 Share Posted November 5, 2014 I had the same issue. Basically the mags warp a little around the mag catch holes. To fix, load your mags up to full capacity and squeeze them in a vice with wood blocks. Start with a little squeeze and apply more and more force until they drop free. Worked for me. Link to comment Share on other sites More sharing options...
KOBGT Posted November 5, 2014 Share Posted November 5, 2014 I have new mags. I have old mags. I have 1 TS where all 12 mags I own, work. I have a new CTS where only 4 mags work. Link to comment Share on other sites More sharing options...
asimonp79 Posted November 6, 2014 Share Posted November 6, 2014 here you go http://www.brianenos.com/forums/index.php?showtopic=193149&hl=%2Bdrop+%2Bfree#entry2142479 Link to comment Share on other sites More sharing options...
wyattptato Posted November 6, 2014 Share Posted November 6, 2014 European guns are made this way they are not supposed to drop free. Link to comment Share on other sites More sharing options...
asimonp79 Posted November 6, 2014 Share Posted November 6, 2014 Really? So CZ ,Tanfoglio, Glock, Berreta - all these are not drop free? Well, I shot /owned all mentioned above - all were drop free Link to comment Share on other sites More sharing options...
huskerlrrp Posted November 6, 2014 Share Posted November 6, 2014 European guns are made this way they are not supposed to drop free. Not true since the 1980's* *Actual date not a fact. Link to comment Share on other sites More sharing options...
BeerBaron Posted November 7, 2014 Share Posted November 7, 2014 actually it depends. many are made that way, duty guns, mil guns. they have the mag brake protrude enough to stop a mag falling out in order for the user to retain the spent mag if required. however, the competition oriented models (shadows, stock II's, whatever) all have a flat mag brake which from factory means the mags should drop out freely. if your mags are hanging up it could be a number of things: bent mag brake grips screws too long and pushing against the mag brake over-pressing on the mag release (trapping the mag) high sport or burr somewhere on the mag or on the mag catch holes on the mag grips soft/weak and putting pressure on the mag when you grip the gun tightly grips too thick putting pressure on the mag even without you gripping the gun burr on the mag catch feed lips touching sear cage feed lips touching slide stop notch mag body itself out of spec (too wide, too long) could be a combination of those. most of those things are easy to check and easy to fix too. Link to comment Share on other sites More sharing options...
mgardner Posted November 7, 2014 Share Posted November 7, 2014 Had problems with my TS and found that the mag release spring was moving out from under the retaining screw and rubbing the front of the magazine. The radius in the pocket it sat in seemed large so I machined it flat and sharp and so far it seems cured. I believe that the spring had pressure on it from the radius in the pocket and as the gun was shot it slid out. Now it fits tightly and doesn't migrate. Yes, I know I voided the warranty but I don't care. Link to comment Share on other sites More sharing options...
TonytheTiger Posted November 7, 2014 Share Posted November 7, 2014 Void the warranty!?!? That puts you in the same boat as every CZ owner I've ever met. Kinda makes me wonder what percentage of CZ's haven't been voided. Link to comment Share on other sites More sharing options...
ohsevenflhx Posted November 7, 2014 Share Posted November 7, 2014 It might be your magazine release spring rubbing on the magazine. I have 3 Tactical Sports, and do my own work on them. Sometimes if your not watching when you tighten the mag release spring screw, it twists your mag release spring enough to rub the magazine. Link to comment Share on other sites More sharing options...
m1agirl Posted November 9, 2014 Author Share Posted November 9, 2014 I will pull it out again tomorrow and look at the above noted. Hopefully come up with a solution because it is very frustrating Link to comment Share on other sites More sharing options...
Craigb555 Posted October 10, 2022 Share Posted October 10, 2022 I have a new .40 Ts 2. Had issue with mags not dropping free, the mag release pushing into the mag well - took it out and filed it so that it does not extend into the mag well. Started shooting it, all was working, then full/ partial mags would hang up about 2/3 out. If they were empty, would fall free. I called CZ today, was told all my mags need tuning? I have 8 mags, that does not seem right? I asked how the tune them, was told in a vice. That the loaded mags can swell….. 8 mags doing this? I this point thinking about sending the gun back. Already had to fix the safety/ mag release/ and now this…. Anyone had this issue - found a different fix? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now