Jump to content
Brian Enos's Forums... Maku mozo!

kneelingatlas

Classifieds
 View Profile  See their activity

  • Posts

    8,154

  • Joined

  • Last visited

 Content Type 

Everything posted by kneelingatlas

  1. kneelingatlas
    The safety is not designed to be used in DA, doing so can damage the sear and/or safety
  2. kneelingatlas
    Yes, all 10mms, 45s and 38 supers are large framed.
  3. kneelingatlas
    Not that I'm aware of, I prefer fixed sights:
  4. kneelingatlas
    Any large frame upper should fit your Match frame (some fitting may be necessary). The front sight from a Limited will work
  5. kneelingatlas
    Is it just me or is the Xtreme chunkier at the beaver tail and trigger guard?
  6. kneelingatlas
    Give it a ride! This is the one I did:
  7. kneelingatlas
    Much better!
  8. kneelingatlas
    I've done the same on a compact Tanfoglio, what type of project are you working on? The single lug peened pretty bad after less than 100 shots of 9 major ammo fired.
  9. kneelingatlas
    Welcome from San Diego, I shoot Pala more than Norco, but I make if up there from time to time.
  10. kneelingatlas
    I've tried a few others and didn't like them nearly as much: They were lighter though.
  11. kneelingatlas
    The one which started it all! This is a Photoshop of my next plan for my TS Open gun:
  12. kneelingatlas
  13. kneelingatlas
  14. kneelingatlas
    You can change the hammer, but it must be a CZ hammer available on another Production legal CZ; which hammer do you have? Most likely there's no reason to change it. Reach reduction kits are not Production legal, but short reset are. Don't worry about the kit, a Type one from CGW or a CZC pre b should drop right in for you.
  15. kneelingatlas
    That could be cool Although I think if I drill holes past the point where I can make major with SP2 under 115gr bullets I'm going the wrong direction. If you have to use heavier bullets or faster powder to make major what's the point?
  16. kneelingatlas
    I'm actually pretty excited to put Eric's comp on a CZ
  17. kneelingatlas
    I dunno, they're actually shooting pretty nice the way they are:
  18. kneelingatlas
  19. kneelingatlas
    Have you read the thread? http://www.brianenos.com/forums/index.php?showtopic=191773 For a Shadow the only difference is that you can fit a Type 3 disco and that there's no firing pin block.
  20. kneelingatlas

    Shadow mag release

    kneelingatlas replied to cnote's topic in CZ

    No it's better to answer here so others can see too
  21. kneelingatlas
    Do it Josh!
  22. kneelingatlas
    Has everyone seen this new V12 from Akai?!? (More accurately a V12i2 or a Y14 ) It's got me tempted to drill an absurd number of holes in one of my guns Although the pistol is pretty small in the frame, I'd bet we'd see a lot more movement if the pistol filled the frame and had a checker board behind it
  23. kneelingatlas
    It doesn't look like I did The stacking tolerances are hit and miss; sometimes you have to fit the safety, sometimes not.
  24. kneelingatlas
    Did you buy one of these: https://cajungunworks.com/product/as-b/ If so that's the set screw he's talking about, if not you can file the factory sear safety leg to fit.
  25. kneelingatlas

    Shadow mag release

    kneelingatlas replied to cnote's topic in CZ

    reversible: To change the mag release you must remove the screw holding the trigger bar lifter spring, this screw may or may not be staked and can be very difficult to remove, so use a screwdriver with a tight fit and maintain constant downward pressure while turning.
×
×
  • Create New...