DKorn Posted September 6, 2018 Share Posted September 6, 2018 Hey all, I’m looking at building my first PCC and I’d like feedback on my plan before I start buying anything. I’m thinking: -Taccom complete ULW upper (~$500) -PSA Complete Glock lower (~$150) This would get me a complete rifle for $650 and let me did my toes into PCC. Once I get hooked, I’ll probably upgrade the trigger and swap out the stock and grip for ones I like better. I could buy just a lower and build it myself, but with how much less expensive the PSA complete lower is it seems like a no brainer. Thoughts? Link to comment
biggulp Posted September 6, 2018 Share Posted September 6, 2018 Solid plan! A lot of guys who are much better than me and who have their choice of equipment choose to run the ULW upper. As far as the lower, while the PSA lower isn't top notch in fit/finish, it's really hard to beat the price for a complete lower. One word of caution, I've heard of a lot of folks having ejection issues with the PSA lowers. Most of the time, the issues are corrected by adding a slight bend to the ejector. Link to comment
Jeff_Alan Posted September 6, 2018 Share Posted September 6, 2018 Slight bend helps if having problems. But be sure to check the set screws that hold it in 1st thing. Maybe a little blue loctite also. Link to comment
Matt1911 Posted September 6, 2018 Share Posted September 6, 2018 (edited) That's the exact setup I have, but with a Rise 140 trigger. It runs awesome with RN bullets. I can't get hollow points to work worth a damn though. So RN it is. I may try the feed ramp taccom offers at some point, I'm just not ready to cut into my upper yet to install it. Edited September 6, 2018 by Matt1911 Link to comment
DKorn Posted September 6, 2018 Author Share Posted September 6, 2018 3 minutes ago, Matt1911 said: That's the exact setup I have, but with a Rise 140 trigger. It runs awesome with RN bullets. I can't get hollow points to work worth a damn though. So RN it is. I may try the feed ramp taccom offers at some point, I'm just not ready to cut into my upper yet to install it. Ill be running round nose anyway. I’m probably going to put the new CMC PCC flat trigger in it since my 3 gun rifle has a CMC flat trigger. Link to comment
pfcchambers Posted September 6, 2018 Share Posted September 6, 2018 Before you drop money on a trigger. Try just the light JP competition springs for 11 bucks or so. I have to PCCs. One with Hyperfire 3g and one with polished mil-spec and the forementioned springs. Hyperfire is better but to be honest when shooting I do not notice. But that combo of springs and polish drastically improves your typical mil spec trigger. Link to comment
Smithcity Posted September 6, 2018 Share Posted September 6, 2018 If you want a reliable pcc that can feed various types of bullets, you will have best luck using an upper, lower, and barrel from the same manufacturer made for 9mm. Link to comment
DKorn Posted September 6, 2018 Author Share Posted September 6, 2018 1 minute ago, Smithcity said: If you want a reliable pcc that can feed various types of bullets, you will have best luck using an upper, lower, and barrel from the same manufacturer made for 9mm. I’ve heard this, but it adds quite a bit of cost. Plus, if I'm going to do my own lower build, I’m going to use a Coda Evolution lower, and they don’t make uppers. Link to comment
Smithcity Posted September 7, 2018 Share Posted September 7, 2018 (edited) 33 minutes ago, DKorn said: I’ve heard this, but it adds quite a bit of cost. Plus, if I'm going to do my own lower build, I’m going to use a Coda Evolution lower, and they don’t make uppers. Then dont be surprised if it is unreliable and does not feed certain ammo. The magazine presentation depth and angle relative to the chamber and chamber type are all critical. The is no milspec for 9mm ARs like there is for traditional 223 ARs Edited September 7, 2018 by Smithcity Link to comment
DKorn Posted September 7, 2018 Author Share Posted September 7, 2018 Just now, Smithcity said: Then Then dont be surprised if it is unreliable and does not feed certain ammo. The magazine presentation depth and angle relative to the chamber and chamber type are all critical. I’m willing to take the time to tune a PCC-specific load if need be. That said, if it’s going to make a big difference I’m willing to look at options. The taccom upper is definitely going to be included, so that won’t change. If I decide to do my own (better) lower assembly than the PSA, what would you go with as far as parts other than the lower itself? Link to comment
Smithcity Posted September 7, 2018 Share Posted September 7, 2018 I would go with all parts from the same manufacturer. Lower, upper, and barrel from JP, or cmmg, or quartercircle10. You can probably get away with a frankenbuild that works with only round nose and requires a specific OAL. Link to comment
DKorn Posted September 7, 2018 Author Share Posted September 7, 2018 1 minute ago, Smithcity said: You can probably get away with a frankenbuild that works with only round nose and requires a specific OAL. Given that it’ll be a competition and range toy only gun, and that I already load only round nose of a specific OAL for my pistol for USPSA, why is this a problem? I’m seriously wondering- many people bring it up as a problem, but then accept without comment that a Limited or Open gun may run only with certain loads. Link to comment
Smithcity Posted September 7, 2018 Share Posted September 7, 2018 14 minutes ago, DKorn said: Given that it’ll be a competition and range toy only gun, and that I already load only round nose of a specific OAL for my pistol for USPSA, why is this a problem? I’m seriously wondering- many people bring it up as a problem, but then accept without comment that a Limited or Open gun may run only with certain loads. Sounds like you know what you are getting yourself into. Shouldn't be a problem if you are ok experimenting until you figure out what runs in your build. Might have to play with different OALs and bullets. I went down this road and was pissed when I couldn't run HPs in my AR9. All my reloads for production minor were 1.145" JHPs and nothing ran reliable in my AR9 except certain shape round nose at 1.13" OAL. Was hoping to use the same 9mm JHPs for both guns. Didn't work out that way. Link to comment
Matt1911 Posted September 7, 2018 Share Posted September 7, 2018 14 minutes ago, DKorn said: Given that it’ll be a competition and range toy only gun, and that I already load only round nose of a specific OAL for my pistol for USPSA, why is this a problem? I’m seriously wondering- many people bring it up as a problem, but then accept without comment that a Limited or Open gun may run only with certain loads. It's not really a problem. If it runs on the ammo you like to use then all is good. I wanted to try using hollow points in mine to maybe get a better knock down at a bowling pin match I occasionally attend but couldn't get them reliable in the setup I use for USPSA. Link to comment
DKorn Posted September 7, 2018 Author Share Posted September 7, 2018 12 minutes ago, Smithcity said: Sounds like you know what you are getting yourself into. Shouldn't be a problem if you are ok experimenting until you figure out what runs in your build. Might have to play with different OALs and bullets. I went down this road and was pissed when I couldn't run HPs in my AR9. All my reloads for production minor were 1.145" JHPs and nothing ran reliable in my AR9 except certain shape round nose at 1.13" OAL. Was hoping to use the same 9mm JHPs for both guns. Didn't work out that way. Right now I’m running 125 grain round nose blue bullets at a fairly short (1.10-1.12) OAL since the PPQ has a pretty tight/short chamber. I figure they’ll hopefully work in the PCC- if not then I’ll experiment and ideally find a load that works for both. Link to comment
Flatland Shooter Posted September 7, 2018 Share Posted September 7, 2018 (edited) I have several barrels that require bullets loaded short (pre-PCC PSA and Spinta) and all run well with the 125 gr Blue Bullets RN loaded at 1.100". The Taccom ULW barrel has a generous throating that allows most bullet combination to be loaded long. You should be good for just about any barrel you choose. Just checked the Taccom website. You can buy the complete upper with a ramped barrel. Cheap insurance. Edited September 7, 2018 by Flatland Shooter Link to comment
Jeremyc_1999 Posted September 7, 2018 Share Posted September 7, 2018 I would go with the taccom Ramped barrel and their bolt, or at the very least the Taccom Glock lower feedramp. Shoot, Tim might even prep the upper for install for you (although it is pretty easy) Link to comment
jkrispies Posted September 7, 2018 Share Posted September 7, 2018 (edited) You’ll also need an optic. The TACCOM handguard will not accept a front iron sight, so you’ll need something like a red dot on an appropriate riser for an AR height firearm. There are 1 million threads on this site about red dots so you can check those out for opinions on that matter. Edited September 7, 2018 by jkrispies Link to comment
DKorn Posted September 7, 2018 Author Share Posted September 7, 2018 13 minutes ago, jkrispies said: You’ll also need an optic. The TACCOM handguard will not accept a front iron sight, so you’ll need something like a red dot on an appropriate riser for an AR height firearm. There are 1 million threads on this site about red dots so you can check those out for opinions on that matter. I have a few optics that can be moved over, but will worry about it separately since the optic can be used on a different gun depending on what I end up preferring for the PCC. Link to comment
mmlook Posted September 7, 2018 Share Posted September 7, 2018 6 hours ago, Smithcity said: Sounds like you know what you are getting yourself into. Shouldn't be a problem if you are ok experimenting until you figure out what runs in your build. Might have to play with different OALs and bullets. I went down this road and was pissed when I couldn't run HPs in my AR9. All my reloads for production minor were 1.145" JHPs and nothing ran reliable in my AR9 except certain shape round nose at 1.13" OAL. Was hoping to use the same 9mm JHPs for both guns. Didn't work out that way. OAL/Feeding limitation is specific to the glock mag if you try to feed a (HP)OAL longer than 1.135 into small frame glock, the same thing will happen. - it's one of the (many)reasons open glocks are not popular Link to comment
stick Posted September 7, 2018 Share Posted September 7, 2018 Your plan is solid. When I first started, I bought a complete PSA upper and lower. I now have three. Two are mine and one is my daughter's. Here's what my setups look like now. All three were once PSA uppers and lowers. Steel Challenge PCC-PSA lower with Hiperfire 24C trigger, Taccom 3 stage buffer with ahort stroke kit Aero Precision Slick side upper with Taccom ULW Ramped barrel, Taccom extreme bolt, Taccom Carbon Fiber Handguard and C-more red dot. Weighs just over 5lbs. Daughter's PCC has a PSA lower with hiperfire 24 3G trigger, Taccom 3 stage buffer with short stroke kit and a Taccom Magwell funnel.. Her upper is a aero slick side upper with taccom ULW barrel with foam hndguard and PSA bolt using a BCM Gunfighter charging handle and C-more red dot. My USPSA PCC is a complete PSA upper and lower with Taccom hiperfire 24c trigger, Taccom 3 stage buffer with short stroke buffer kit, laser, BM aluminum magwell and c-more red dot. It weighs 8lbs. I just ordered the Taccom tension barrel and a carbon fiber handguard in an attempt to lighten up the gun. The moral of the story is this...Get what you can now. Try out PCC. If you like it, you can make changes to your current setup and still have a decent base from which to build from. Link to comment
Aircooled6racer Posted September 7, 2018 Share Posted September 7, 2018 Hello: Or if you can assemble things you could build a pretty damn nice one for $1100 with a very good trigger and optic. Thanks, Eric Link to comment
Smithcity Posted September 7, 2018 Share Posted September 7, 2018 6 hours ago, mmlook said: OAL/Feeding limitation is specific to the glock mag if you try to feed a (HP)OAL longer than 1.135 into small frame glock, the same thing will happen. - it's one of the (many)reasons open glocks are not popular Those same rounds feed fine in a JP rifle with the same glock mag. Link to comment
jkrispies Posted September 7, 2018 Share Posted September 7, 2018 1 hour ago, Aircooled6racer said: Hello: Or if you can assemble things you could build a pretty damn nice one for $1100 with a very good trigger and optic. Thanks, Eric It sounds like a funny response, but there's a lot of truth to this. Folks who buy things complete often end up throwing away 3/4 of their parts and replacing them with something else, which is actually more expensive in the long run than just doing your research and buying once and crying once. Of course, if you're not sure about diving into PCC for the long haul, then going less expensive may be the better choice. I personally would recommend investing in a high end trigger sooner rather than later. As far as the optic goes, if you have some extras already then run what you have while you test drive other guys' equipment in the meanwhile. Link to comment
DKorn Posted September 7, 2018 Author Share Posted September 7, 2018 1 hour ago, jkrispies said: It sounds like a funny response, but there's a lot of truth to this. Folks who buy things complete often end up throwing away 3/4 of their parts and replacing them with something else, which is actually more expensive in the long run than just doing your research and buying once and crying once. Of course, if you're not sure about diving into PCC for the long haul, then going less expensive may be the better choice. I personally would recommend investing in a high end trigger sooner rather than later. As far as the optic goes, if you have some extras already then run what you have while you test drive other guys' equipment in the meanwhile. I’m actually thinking about borrowing a buddy’s PCC for a match just to see if I like it. Link to comment
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now