Hawk21

No I purchased used from a buddy he doesn’t have box or any spare parts

Lost a ball out of the dropper assembly and took one of the others to local industrial equipment supplier to find some replacements. When attempting to install the new ones I lost the only remaining original ball.....which wouldn’t have been a problem except the replacements are too large and don’t fit into the die. Can someone confirm the ball size is 4mm? I failed to specify metric upfront so if anyone needs approx. 150 3/16 chrome alloy grade 25 balls send me your address!

What division do you shoot in 3g? Do you currently or plan to shoot any other disciplines like uspsa, steel, or idpa?

I would call Dillon and see if they can send you a new slide spring and cap (13937, 14574) as they may be causing the guide to occasionally index out of position

Do the majority of their workouts require you to be at a full gym or can they be completed from home with an assortment of free weights?

Great advice so far regarding safety being your number one A+ priority. You need to set your expectations in line with that so you don’t get bummed if you are not in the top 1/3 of the results. First few matches your goal needs to be JUST finish all stages. It’s all new to you so don’t get bummed when you forget a hidden target or a lone piece of steel and end up with a couple failure to engage penalties. As said earlier main thing is slow and steady with focus on muzzle and trigger finger. If you end up first or in the early group of shooters just ask to go later so you can see others run the stage. Typically everyone will be eager to help you out and accommodate that request. Last thing that I have seen a few folks screw up that Rojo mentioned in his post was going cold at the end of a stage. The timer stops at your last shoot so there is absolutely no reason to rush this process. Keep your muzzle downrange and just talk through the process with the RO if his commands don’t make clear sense to you. Enjoy and Good Luck

https://www.laser-ammo.com/laser-training This link may help some folks get a better idea of what I think the op was discussing. Several similar systems out there, most of the apps are not brand specific and can work with any laser cartridge. G-Sight is the only app I have found that’s free

When used in conjunction with an app you have the ability to keep focus where it should be and view your hits after a dry fire string. Just ordered the sure strike cartridge and plan to use it with the free G-Sight app, but as jack pointed out with a 2011 I’ll have to cock the hammer each time. I’ll report back later this week with how the system works out.

I know this isnt related to PCC but has anyone seen other pistol mount options besides Tevo ?

Two holes

Going 3n37 as I didn’t want to be spilling powder out of every case

Need a starting point for 3n37 under PD 124 JHP out an Infinity AET 5” .....thanks in advance!

Find a commercial address on the receiving end and cost will be cut in half for UPS. Shipped one several months ago and it was $80 halfway across the country.

Yep that’s what I figured thanks for confirmation

Doesn’t look to be built for the competition crowd more of a duty piece. Much like Wilson Combats PCC I’d bet they will be tough as a diamond, priced higher than giraffe ears, but not useful for the serious PCC shooter.

Pacakage contained (4) of these so I assume it uses the existing bolt thru the case feeder support, if not then I’m of need also

I have a new one sitting at my office will send info over in the AM if no one is able to help you out sooner

Bling bling! Looks great, what do you plan to finish the grip and small parts with? Were the parts in the white when you sent them in, or can they take previously coated parts and refresh?

Thanks for the info. I just left a message, will wait and see what he says.

Has anyone fit a Mitchell Right Side Mag release in a PT Evo ? The release binds once the left side of it (where the screw installs) clears the magwell of the grip and reaches the interior left side of the grip. I have reduced the diameter with countless spins in 180 then 320 sandpaper but before i continue down that road I figured it would wise to check in and see if anyone else has installed this set-up to date?

Paranoia warranted avoid the “S” word at all cost If it turns out you don’t like seating and crimping all in one, a WiFi endoscope looking into the case as it exits the powder measure station is the most common way to verify charge has been dropped. I original ordered the wired version but couldn’t get it to connect to an old kindle fire I had laying around and returned it for the WiFi version I simply connect to my phone now. Several threads on how some guys are using the wired endoscope connected to a simple vehicle back up monitor on here as well.

Tacomandood today is your chance if you wanna go for the real thing DAA has it discounted plus Presidents’ Day sale coupon code !!!!

I have never been on the other end of a Razor but will put in a vote for the Burris xtrii 1-8x24. I have been very pleased with its clarity and it’s built like a tank (34mm main tube). They are worth a close look at that price point.

Tacomandood give us a R&D update when possible. I am about to rough something out and wanted to see which components you decided and how they are working out first. Thanks

Now that makes sense! I’m not gonna lie... I goggled 90degree RTS2 Mount wondering if I was late to the party.