CZ85Combat

Finally got a Czechmate on the way. Now to figure out a load. I have 11lbs of N350. Have 115 & 124 jhps & RN. I also have a reamer so if necessary can lengthen the throat. any load data would be appreciated. Bullet type, charge weight, OAL, avg. fps, ES, SD, other info thanks Dave

amazon must have sent you the wrong holster! The matches I go to there must be at least 10-15 guys using that holster. send it back and get the boss hanger & holster from http://www.benstoegerproshop.com/BSPS-BOSS-Dropped-Offset-DOH-Holster-p/bsps-holster.htm

here you go. 1. http://www.benstoegerproshop.com/BSPS-BOSS-DOH-Holster-Ghost-Pouches-DAA-Belt-p/boss-kit.htm 2. http://www.benstoegerproshop.com/BSPS-BOSS-Plus-DOH-Holster-p/bsps-holster-plus.htm

do you have a link? I can not get any thing to come up on Gunbroker for czechmate.

+1^ rounds are too long

you need a reading g-rx push thru die https://www.youtube.com/watch?v=SYnbeUhzqLk

well I think the custom shop can fix you up. they can put the ACCU-BUSHING on a TS. They have done 1.308" @50yds, and 4.574 @100yds http://www.czfirearms.us/index.php?topic=68993.0

this would a good one to start with. you can pick one up for $620--$660 http://cz-usa.com/product/cz-75-sp-01-tactical-9mm-black-3-dot-tritium-sights-18-rd-mags/

i realize what you are saying, i did the push test earlier, with the extreme 124gr FP bullet, i came up with 1.142, loaded a few dummies at 1.125 and they go in fine and for some reason the 1.100 do too now, wonder if the 15 deg weather had something to with that, but here in the 70 deg basement they work slick, you can see on the feed ramp where the plating contacts on the ramp. if push test came up with an OAL OF 1.142 then why did you load up at 1.100? 1.125 is what you should be trying.

the plunk test is not the push test

does this only happen with a full mag and only the first round? does it load with a 1/2 full mag? does the round noes dive into the feed ramp? more info is needed to help you out. Your OAL should be determined by the push test(see link) not just jumping 0.050. and going that short will add more problems http://www.czfirearms.us/index.php?topic=34225.0

yes,but CGW also sells the CZC Competition hammer that is a factory part.

same function, one is legal to use in competition one is not.

you have to put it together yourself. Takes two guns to make one. you need 1 PO1 frame & 1 RAMI slide.

yes off the web site. http://czcustom.com/cztacticalsportextendedbasepadBlack.aspx

My last lot of N320 ran slower, had to go to 4.45gn to get the same results

the extended basepads are not intended for the 9mm TACTICAL SPORT only the 40 From CZC Can be used on the TS 9mm but will NOT increase the capacity. The ribs on the TS 9mm mags will catch on the cartridge and or follower. Unless you are using the new CZC Spring and Follower 10522

^^^^^^^^ I have done all the above

Moral of the story, Don't remove that screw unless it is a must to replace the spring!

Got mine looks good. Now too find a czechmate to put it on. Been looking for one since September. Can anyone help me find a new one?

Take your slide & grips off, Look and see if the trigger bar spring is in the groves on the trigger bar. insert the mag, work the trigger, look & see if the mag is rubbing on the trigger bar or spring. Trigger bar spring screw needs to be tight just not over tight.

That sounds more like a 2X charge or bullet set back. This says it all "Headstamp was printed in the breech face, primer blown out, and case blown out where the chamber is unsupported." "While i do check charge weights every 50 rounds or so, it wasn't often enough." No No NO every time you stop to check you add more chance to make a mistake. set your charge weight an reload, when you are done do a check at the end. now if you have poor equipment and you charge weight changes with out you changing the setting, then you have other problems.

Stainless steel, you don't need to change it

This is the one you need http://czcustom.com/czcomphammerlowfat.aspx

You can fix this. You need, CGW's exclusive adjustable billet sear. # AS-B http://www.cajungunworks.com/cgw_race_hammer.html