RePete

The last time I chrono'd AE 230gr was in April 2011 and the PF was 199318 and previously in 2008 it just over 181.

The Speed Beez looks like it's made by Comp Tac.

Arkansas is done, it's now Texas. I said this when the 2015 RB came out, but the answer that Ken Reed gave me was "The RB was written by PHD's, engineers etc." and my response was "And not one of them cannot write a RB!"

That would be illegal. Only 1 fault line per position. You can set the fault line so that you are exposed to all targets but if you are behind the fault line, you are considered to be in cover.

Do you mean at one position or one on each of the shooting positions?

Then you start!

I've never seen it in over 35 years of competing but that's not to say it hasn't happened. Some of the revolvers I have seen have the mod pictured and described.

The strain screw was always meant to be bottomed out. @Swordfish. I have never had one back out that was torqued down. This is the picture of described above. https://i.imgur.com/Bm4fuoz.jpg[/img]

Nor do I, but you can touch it when reloading, grabbing the cylinder which is also very hot.

After about 12 rds it's too hot to hold.

Was at the range and got into the seacan, after using the tractor to scoop away the snow. Here is the method of hanging the wall to the upright. The small eye is use to zip tie the bottom part of the wall to the upright. You can use the upright to hold 3 or 4 wall ends.

Here is my fix. Take a Dillon pin (bent), cut off the pin and file smooth and square, drop in a Lyman decapping pin (7837786), then the Dillon bushing, and reassemble.

No course for ICORE, the IDPA course I teach, in Canada, will cost $20.00 and there isn't a course in the US (just like USPSA), I also instruct PPC and it's only $25.00, but it's all but dead in the east. IDPA membership is $40.00/year, ICORE is, IIRC, $25.00/year and USPSA is $25.00, PPC? I don't know.

IMO the black badge course is a money grab, and if you let your membership lapse for more than 3 years , you must take it again. The course costs $225.00'ish for Ontario. Membership is $70.00/year.

Read page 5. https://forums.brianenos.com/topic/270290-sti/page/5/

I will have to take more pics once the snow goes and then I can post here.

I know this is a necro post but, I made 52 walls for my club using 8' 2x2 (2 per wall),4" security netting for the walls and a ball bungee to hold the wall together when rolled up. The walls with a window opening are 2 strips of netting with the opening in the middle. In the ends of the top rail is a 1/8" x 4" eyes and in the ends of the bottom rail is an eye. The uprights are 2x2's with #10x3" screwed in one end. The upright support is dictated by the range floor. The bottom picture show 33 walls in the crib.

Here is the MSDS sheet. https://ballistol.com/wp-content/uploads/2016/09/SDS-WTC-Ballistol-Multi-Purpose-Liquid-Revision-4.pdf Maybe you could add a deodouriser to it.

I have all square notch sights but it's fine. I don't think that in competition you'll notice the difference.

Is it because they want them? Supply and demand.

I just received a set and installed on a P320. I've just received a set and installed, and while I haven't shot the gun yet, they are nice. They are made by HiViz for SIG. HiViz are not selling them due to the contract.

The price is in the third paragraph. $969.00

Look here. https://kleenbore.sellerscommerce.com/search?phrase=magazine&f=kleenbore&t=b&storeId=109

How much major?

What the power factor and what is the recoil like?