rishii

Not the Frankfort arsenal, I have one and it kinda sucks compared to the Lyman it replaced

Yep use the hammer type

Thanks for the info, I’ll be picking one up soon

Any updates on these guns, any issues so and how are they holding up?

I had a similar problem I used a dremel with a craydex polishing tip and polished out the slots and with the aftermarket solid ejector solved it

big plus one to the above Also I’ve learned never to reuse the screws, if you remove them, toss them and fit up new ones If you reuse the screws there a good chance the next time you remove them one of them will round, then it’s screw extractor time on a tiny screw

I hear you about optic planet, my experience with dvor has been mostly positive, their prices are not that great, it every so often they do have a great sale I already received a shipping notice and should have it tomorrow

Dvor.com has the holosun 507 comp on sale, both red and green

I’ve used cmc, hyperfire and JP triggers i I didn’t like the hyperfire, the trigger pull reminded me of a really nice Glock trigger I have a cmc, it broke a spring, it still functioned but the reset was soft, sent it back and cmc fixed it quickly I’m running the JP in my main gun and so far so good

My reloading bench has a framed 2x4 shelf that sits flush with the floor that I put all the heavy stuff reloaders need like bullets, tool boxes, etc. I have no idea how much it weighs fully loaded, but my bench doesn’t move at all when I’m loading

The blues will be faster one thing I used to do back when I shot 38 SC in open was I’d load 124 jhp and 115 blue with the same powder charge, the 115s were faster and they both chrono at about the same PF

I would get the basic conversion kit, minus the powder measure and any other parts you might already have if you already load 45acp, you have the shell plate if you’re like me and have dedicated powder measures for your pistol calibers, you have the rifle powder bar sitting in a drawer, I have those set for my rifle loads and swap out the powder bar from my pistol powder measure, fine tune and load

Thanks for the clarification, I was hoping that caspian would start selling those frames again

Question on the caspian frame, SS or wide body last I check caspian didn’t show the high cap frames or parts on their website

Limcat i have one and it cut to clear the slide https://www.speedshooter.com/product/limcat-shielded-thumb-rest/

In the past they ran a Black Friday sale they do have a 5% brian enos forum discount and quantity discount

Also look at the ghost holster ultimate evo That’s their race holster, very adjustable and smooth draw hanger is a little flimsy but read that they improved it

I’m running a Romero 3max and so far so good, no problems with it I also have a couple of V4 rts 2s, the Romero is drastically brighter and the larger window size makes it easier to pick up the dot during SH/WH the holosun 507 competition looks to be a contender but their too new know for sure

I finally received mine and installed it in a QC10 colt lower, after reading all the comments on AR15 on how hard it is to rack, I picked up a Techwell tac latch L which allows me to grip it with 4 fingers. https://techwellusa.com/advanced-ambi-arc-l-charging-handle-for-ar-platform-223.html my initial install I simply pushed it in and used the buffer detent to hold it and I couldn’t close the upper, it would almost close and I ended up forcing it shut. Racking it was easy and I realized I had bypassed the rollers by forcing it shut i removed the detent and back the tube out 1 turn and closed the upper without any issues racking it went from easy to omg, the unit was shipped bone dry and I put slideglide lite on the roller lock area which made it easier to rack testing was done at 10 yards on a NRA B-8c repair center with my 115 gn, 135 PF PCC loads which are subminor out of a pistol, the 1 st mag was loaded with 4 rounds to test function and to see if it would lock back, the gun functioned and locked back and the saw the dot never left the black on the target. Next loaded a 42 round mag and did a series 2 shot as fast as I could pull the trigger and not waiting for the dot to settle, again the dot didn’t leave the black and except for a few flyers all the shots were in the black and the majority were within the 10 ring i also tested with my regular production/SS/co ammo doing the same drill and noticed a bit more dot movement with the dot moving the the outer edge of the black So far I’m liking it

Dillon casefeeders uses 4 different plate sm pistol lg pistol sm rifle lg rifle you swap the plates for the different calibers

I just got a shipping notice from Maxim, I should get it next week

Ditto i ordered mine on 06-18, also sent a email a month ago and got the call and he said they should get their next batch in about 10 days, he further offered cancel my order without the restocking penalty which I declined mainly because our range is being used by the EPA as a hazmat staging area from the Lahaina fire and it’ll be months before it reopens

Old doesn’t necessarily mean obsolete I’m still using my MK IV, replaced the sky screens a couple of years ago i think the real reason is there are newer cheaper units like the competition electronics pro chronograph or newer technology like the labradar and magnetospeed

not yet I have magnet holders on all my rigs including my PCC rig that I usually have a fully loaded 40 round steel colt mag and even something that heavy doesn’t come off without a good tug

Blade tech on a lee holster hanger i run 4 safariland 771 pouches and 2 magnets form lee holster hangers the magnet are the 1st and last with the 4 safariland between them i use the last magnet holder for my Barney mag and the 1st one for the make ready mag i used to run a pouch in the last position but for tired of fumbling trying to get the mag back into the pouch after I Barney