Bucky Posted April 12, 2007 Share Posted April 12, 2007 Topic says it all. Whose primers are the softest after Federals? Is it Winchester small pistol? How are the Remingtons? Word is that the CCIs are very hard. Either way, I'm figuring I'll have to up my mainspring weight on my production gun. TIA. Link to comment Share on other sites More sharing options...
reneet Posted April 12, 2007 Share Posted April 12, 2007 I believe that Remington is the next in line. CCI are the hardest. Link to comment Share on other sites More sharing options...
Carlos Posted April 12, 2007 Share Posted April 12, 2007 Anyone try the Wolf brand? Are they made in Germany like their shotgun slug ammo? Link to comment Share on other sites More sharing options...
superdude Posted April 12, 2007 Share Posted April 12, 2007 i've heard that the Winchesters are the next softest after Federal. Some folks claim that the remingtons are as hard as the CCIs. i have no data to support any of this. this is all hearsay from this and other forums. Link to comment Share on other sites More sharing options...
MasterLefty Posted April 13, 2007 Share Posted April 13, 2007 I believe that Remington is the next in line. CCI are the hardest. I don't know where the Remington's fall in the mix, but I lost a slide 13 year's ago due to Remington's (back in the last primer shortage). In less than a thousand rounds, I had a full circle of erosion on the breachface. The primers wouldn't seal. Just my own experience with Remingtons. Kenny (I'm well stocked on Federal's) Link to comment Share on other sites More sharing options...
DougCarden Posted April 13, 2007 Share Posted April 13, 2007 I would try Remingtons, then Winchester. I would first buy a Hand primer, sounds like the RCBS model is pretty good, and hand prime your match ammo with the Rems or Feds, making sure that they are all pre crushed. Then try them with your reduced actions and see if they will run. I know it will be a little more work, but try it. It may work fine for the match ammo. Another option is to find your buddy with a 1050, buy him some beer, and come over and prime your brass with it......(you can adjust the depth of the primer depth, and precrush the primers until you see the anvil pushing up on the primer face). I think that would ensure that your match ammo is 100% reliable and ready to go....just another option to try..... Good luck, DougC Link to comment Share on other sites More sharing options...
wide45 Posted April 13, 2007 Share Posted April 13, 2007 What type of primer? I found that CCI large pistol primers light easier than Win. large. Win. small pistol light easier than CCI small. YMMV Link to comment Share on other sites More sharing options...
glock_556 Posted April 13, 2007 Share Posted April 13, 2007 (edited) I have been using Fed primers exclusively since I started reloading for 9mm. Well, around here, Fed primers are now non-existant so I bought 200 Win small pistol primers and loaded them up. I could not believe how much easier the Win primers seated than the Fed primers (using Dillon 550B). I mean it was daylight and dark on the ease that the win primers seated over the fed primers. Don't get me wrong, I didn't have to "cram" the fed primers in, but the win primers just seem "smoother" Now, I shoot a G34 in production and use a lightened trigger striker spring. Out of 200 rounds today, I didn't have one single light primer strike. I'm sold and bought 10K win small pistol primers. YMMV Edited April 13, 2007 by glock_556 Link to comment Share on other sites More sharing options...
Bucky Posted April 13, 2007 Author Share Posted April 13, 2007 Now, I shoot a G34 in production and use a lightened trigger spring. Out of 200 rounds today, I didn't have one single light primer strike. I'm sold and bought 10K win small pistol primers. YMMV Are you talking about a lightened striker spring? A lightened trigger spring should have no effect on how hard the striker hits the primer. I would try Remingtons, then Winchester.I would first buy a Hand primer, sounds like the RCBS model is pretty good, and hand prime your match ammo with the Rems or Feds, making sure that they are all pre crushed. Then try them with your reduced actions and see if they will run. I know it will be a little more work, but try it. It may work fine for the match ammo. Another option is to find your buddy with a 1050, buy him some beer, and come over and prime your brass with it......(you can adjust the depth of the primer depth, and precrush the primers until you see the anvil pushing up on the primer face). I think that would ensure that your match ammo is 100% reliable and ready to go....just another option to try..... Good luck, DougC The XL650 has no stop for the primer system, so doesn't it always seat the primers until they are flush? I still have a couple sleeves of the Feds left, so I'll save them for the big matches and should be ok. What type of primer? I found that CCI large pistol primers light easier than Win. large. Win. small pistol light easier than CCI small. YMMV Ah good point. I was referring to small pistol. Link to comment Share on other sites More sharing options...
glock_556 Posted April 13, 2007 Share Posted April 13, 2007 Oops, I meant striker spring, not trigger spring. Link to comment Share on other sites More sharing options...
LPatterson Posted April 13, 2007 Share Posted April 13, 2007 What type of primer? I found that CCI large pistol primers light easier than Win. large. Win. small pistol light easier than CCI small. YMMV Not in my 625 they didn't. Star brass primed with CCI's had a light strike 1 in every 3 moons while brass looking Winchesters worked for 200 rounds straight. I still have brass primed with nickel plated Winchesters WLP. I only prime with a RCBS hand primer. Link to comment Share on other sites More sharing options...
vluc Posted April 13, 2007 Share Posted April 13, 2007 Have not used Winchester in years. What kind of change (if any) could you expect to see in your load switching from Federal to Win primers? Link to comment Share on other sites More sharing options...
sargenv Posted April 24, 2007 Share Posted April 24, 2007 (edited) I tried using the brass colored Winchester small pistol primers in my 627 with a C&S extended firing pin and a 13 pound mainspring. Out of 200 rounds fired, I had 3 failures to fire. I have not tried the Remington primers I have in stock yet, but will be trying them next. The Remington primers I have are about a year old. The Winchesters are between 1 and 2 years old. I too have heard that CCI's are the hardest to light and do not use them in my 650 due to the 650 jamming constantly when I tried them. Vince Edited April 24, 2007 by sargenv Link to comment Share on other sites More sharing options...
Sean Gaines Posted April 24, 2007 Share Posted April 24, 2007 Anyone try the winchester small pistol magnum. I bought 1k of them to try, haven't got around to trying them yet. Link to comment Share on other sites More sharing options...
scooterj Posted April 24, 2007 Share Posted April 24, 2007 I have been having very good luck with the Rem spp in my Smith 627 with action work. Have not had as much luck with Rem lpp in my 625. Link to comment Share on other sites More sharing options...
SLM Posted April 25, 2007 Share Posted April 25, 2007 I've READ that MagTech primers are very close or equal to Federal in that softness department. I emphasize READ that they work well in wheel guns with light springs. I have no experience with them. Just wanted to pass along the information. Link to comment Share on other sites More sharing options...
Steve Anderson Posted April 25, 2007 Share Posted April 25, 2007 Flex has had a major headache with magtech primers in his Glocks...I swapped him for Feds cause I got tired of watching him shoot a Glock Derringer. So it would seem magtech is not recommened for modified Glocks or other light strike sensitive platforms. Winchester works very well in a 650, much better than federal. SA Link to comment Share on other sites More sharing options...
DougCarden Posted April 25, 2007 Share Posted April 25, 2007 Guys, when I get home next week I am going to use my 1050 and prime a bunch of Revo ammo, using Fed, Win(non-new box), and Rem small primers and report on the findings. We know that CCIs are hard as some of my friend's heads...and you know who you are... I am afraid that you will need to use a hand priming tool for your ammo, or find a friend that has a 1050 to "crush-fit" prime your brass and then load like normal on your press. Another option will be to make your action heavier ....... Nah, I didnt think that would be a popular option...... See ya, DougC Link to comment Share on other sites More sharing options...
Matt Cheely Posted April 25, 2007 Share Posted April 25, 2007 Last time I shot remington primers out of my 686 I had to crank the spring up quite a way... FYI Link to comment Share on other sites More sharing options...
lcs Posted April 25, 2007 Share Posted April 25, 2007 I hope this link works. If not just copy and paste to IE in the URL line. http://www.jamescalhoon.com/primers_and_pressure.php Link to comment Share on other sites More sharing options...
gm iprod Posted April 30, 2007 Share Posted April 30, 2007 Although this info is 12years old I believe it to be still quite useful. With the foloowing proviso. Federal now market the #200 as a Magnum Small Pistol, all reference to this primer being suitable for rifle has gone. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now