alzo Posted October 11, 2006 Share Posted October 11, 2006 (edited) So many of the users of this forum advocate using Hodgdon Clays. However, I have seen several users mention significant problems with consistent metering of Clays on their progressive presses. So what's the scoop ? Does Clays meter well on say, a Dillon press, or is it problematic in that regard ? Edited October 11, 2006 by alzo Link to comment Share on other sites More sharing options...
JD45 Posted October 11, 2006 Share Posted October 11, 2006 My scale tells me that Clays is metering as good as Titegroup, and sometimes better. The press is a Square Deal B. Link to comment Share on other sites More sharing options...
DougCarden Posted October 11, 2006 Share Posted October 11, 2006 CLAYS works well until you go below 3.0 grains, as it can bridge in the powder measure. You may see a .01-.02 variance when you start, but check it when you have cases in all the stations and you should be just fine. DougC Link to comment Share on other sites More sharing options...
XD Niner Posted October 11, 2006 Share Posted October 11, 2006 (edited) I have had 0.1 gr variations on my XL650 but after a few rounds it seems to be pretty consistent. A variation of 0.2 gr is about as much as I've seen and then only if I've had some type of interruption in the loading process. Edited October 11, 2006 by XD Niner Link to comment Share on other sites More sharing options...
kevin c Posted October 11, 2006 Share Posted October 11, 2006 Clays is a light, low density flake powder, so it can bridge (clog) in the funnel and drop a light charge, then perhaps a heavy one right after, and may pack differently in the powder bar opening depending on how much settling occurs as the press vibrates through the reloading cycle. Consistent press operation, the same on each and every stroke, helps. I personally think that a little bit of consistent vibration may also help "shake down" the bridging, and may also make settling a consistent charge into the charge bar better. Link to comment Share on other sites More sharing options...
HSMITH Posted October 11, 2006 Share Posted October 11, 2006 I run my 550's like I am mad and Clays meters to within a tenth every time on time loading progressively. I have thrown down to 2.5 grains for some light 38's and 9mm stuff without a problem, they were all right where they should be. The Dillon measure really is good, it will handle just about anything you put in it and meter it very consistently. Link to comment Share on other sites More sharing options...
epj Posted October 11, 2006 Share Posted October 11, 2006 I recently checked my Dillon 550 by throwing 10 charges of 4 gr of Clays. The 10 charges weighed 39.9 grains. On the AVERAGE, it is very accurate and consistant. Link to comment Share on other sites More sharing options...
FTDR Posted October 22, 2006 Share Posted October 22, 2006 never had a problem with a Dillon 550, and get a sd around 9 Link to comment Share on other sites More sharing options...
Merlin Orr Posted October 22, 2006 Share Posted October 22, 2006 I run my 550's like I am mad and Clays meters to within a tenth every time on time loading progressively. I have thrown down to 2.5 grains for some light 38's and 9mm stuff without a problem, they were all right where they should be.The Dillon measure really is good, it will handle just about anything you put in it and meter it very consistently. I agree with Mr. Smith.. I also think that if you run a press with "abandon" it might actually be more consistent due to the vibration actually preventing powder bridging and ensuring a good and constant powder flow and drop. Link to comment Share on other sites More sharing options...
Run n Gun Posted October 22, 2006 Share Posted October 22, 2006 I just loaded 2500 rounds of 45 with Clays and I thought about this thread, so I checked the powder weight every 2-300 rounds. 4.0 grains, on the nose, EVERY time. BTW, I load with a 650. Ed Link to comment Share on other sites More sharing options...
Carmoney Posted October 22, 2006 Share Posted October 22, 2006 drop a light charge, then perhaps a heavy one right after In theory, it might be possible for the measure to throw a light charge for various reasons, but I don't think there's any way it could throw a heavy charge. A powder measure meters powder by volume. Link to comment Share on other sites More sharing options...
SiG Lady Posted October 22, 2006 Share Posted October 22, 2006 Every time I check the weight on the random load or two, it's always right-on. Use Clays at about 3.5gr per load. Works fine for me on the SDB. Has been that way ever since I set it up about three years ago. Rounds at firing FEEL consistent as hell, too. No discrepancies. Link to comment Share on other sites More sharing options...
Aircooled6racer Posted October 23, 2006 Share Posted October 23, 2006 Hello: On my SDB it meters very well. I check my loads more often than most about every 50 or so. It slows me down a bit but I have fun reloading. I also think the slight jarring of the press may help with the metering. Hope this helps. Thanks Eric Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now