RCKable Posted April 12, 2022 Share Posted April 12, 2022 Any suggestions is greatly appreciated. Even a suggestion of sell the ammo is a consideration. For those using a Taccom upper do you have any issues with flat nose rounds? It’s like they over shoot the barrel hole and get wedged between the sure feed insert and the barrel. I constantly have FTF with 147g flat nose, the first round goes in no issues but then as I shoot I might get one or two good before a FTF. Sometimes I get FTF with syntech 150g/130g as well but no where near the same consistency. Never a single feed issue with round nose, reloads or factory 147,124,115. It happens with Glock factory mags and PMags. My build is a taccom signature upper w/ ULW super feed Barrel, standard bolt, adjustable recoil system on a aero epc9 lower. Link to comment
egd5 Posted April 12, 2022 Share Posted April 12, 2022 IMO, flat nose are the worst to feed in anything and round nose is the best. I'd sell it. Link to comment
RCKable Posted April 12, 2022 Author Share Posted April 12, 2022 Guess with it being my first build got a little freaked out that something might not be aligning correctly or worse bought something that doesn’t like another brand. Link to comment
Walli Posted April 12, 2022 Share Posted April 12, 2022 The problem might be the lower and not the upper. Do you have access to a different lower? Link to comment
RCKable Posted April 12, 2022 Author Share Posted April 12, 2022 2 hours ago, Walli said: The problem might be the lower and not the upper. Do you have access to a different lower? I do not, but of course I did see lot of posts with folks complaining about the aero epc9 and feed issues. However most of them are using a aero upper as well. I had been looking at a couple other lowers. QC10, Spikes Tactical, and Spartan. Link to comment
Mongo68 Posted April 13, 2022 Share Posted April 13, 2022 (edited) I just got one of those uppers on sale and same thing with NFA lower. Crazy thing is I have the taccom barrel on another PCC with NFA lower/ upper and flat nose feeds just fine. I have no idea whats going on, but it frosted me so I stuck it in the back of the safe and Im shooting pistol next match. LOL Edit: Im not convinced I didnt do something wrong assembling it. I'll look eventually... Edited April 13, 2022 by Mongo68 Link to comment
bigdawgbeav Posted April 13, 2022 Share Posted April 13, 2022 12 hours ago, RCKable said: I do not, but of course I did see lot of posts with folks complaining about the aero epc9 and feed issues. However most of them are using a aero upper as well. I had been looking at a couple other lowers. QC10, Spikes Tactical, and Spartan. Have you reached out to @TRUBL at Taccom to see if he has any advice? Also, what is your OAL on those rounds? Have you tried seating them a little deeper? Link to comment
TRUBL Posted April 13, 2022 Share Posted April 13, 2022 Take the barrel and polish a bigger radius on the entry, right below the super feed option.....that should do the trick. Don't go crazy, but a little polishing in that area will go a long way! Link to comment
RCKable Posted April 13, 2022 Author Share Posted April 13, 2022 (edited) 5 hours ago, bigdawgbeav said: Have you reached out to @TRUBL at Taccom to see if he has any advice? Also, what is your OAL on those rounds? Have you tried seating them a little deeper? Sorry should’ve mentioned that they are factory Federal ammo. edit; I did contact to Tim, and he said I should try to polish it. Edited April 13, 2022 by RCKable Link to comment
RCKable Posted April 13, 2022 Author Share Posted April 13, 2022 4 hours ago, TRUBL said: Take the barrel and polish a bigger radius on the entry, right below the super feed option.....that should do the trick. Don't go crazy, but a little polishing in that area will go a long way! I will have to try that. You’re the 3rd person to tell me to try that. Link to comment
bigdawgbeav Posted April 13, 2022 Share Posted April 13, 2022 2 hours ago, RCKable said: Sorry should’ve mentioned that they are factory Federal ammo. edit; I did contact to Tim, and he said I should try to polish it. Gotcha... since factory maybe loaded a little long. But don't have experience with it. Thanks for the update Link to comment
mrvip27 Posted April 15, 2022 Share Posted April 15, 2022 A thing to consider. Not all Glock lowers are the same in the angle/spacing from the magwell to the barrel ramp. Some gap farther than others. There is no real standard per say. Link to comment
Mongo68 Posted April 16, 2022 Share Posted April 16, 2022 On 4/12/2022 at 6:13 PM, Mongo68 said: I just got one of those uppers on sale and same thing with NFA lower. Crazy thing is I have the taccom barrel on another PCC with NFA lower/ upper and flat nose feeds just fine. I have no idea whats going on, but it frosted me so I stuck it in the back of the safe and Im shooting pistol next match. LOL Edit: Im not convinced I didnt do something wrong assembling it. I'll look eventually... Update (kind of): Round nose snap caps cycle fine. Going to try syntech 150's tomorrow. Link to comment
philmadxx Posted April 16, 2022 Share Posted April 16, 2022 I was under the impression that these barrels were the best and fed everything - but they need polishing? Link to comment
TRUBL Posted April 17, 2022 Share Posted April 17, 2022 4 hours ago, philmadxx said: I was under the impression that these barrels were the best and fed everything - but they need polishing? They ARE!!!......we can't control everything ya know. But our barrels will give you the absolute best chance of feeding just about any bullet profile out there. We all know that flat nose and hollowpoints will give any AR9 fits.....depending on magazine or lower, this is a little bump on the road. And does not speak to the 100's, if not 1000's of barrels we've produced in the last 4 years. IF he can't get it.....of course we will have him send the barrel back for inspection.....even we don't get it right every time and THAT is where our customer service comes in. I will say.....this is a rarity....the only other time we've had an issue was when a guy was trying to feed HST hollowpoints. Tim Link to comment
RCKable Posted April 17, 2022 Author Share Posted April 17, 2022 15 hours ago, TRUBL said: They ARE!!!......we can't control everything ya know. But our barrels will give you the absolute best chance of feeding just about any bullet profile out there. We all know that flat nose and hollowpoints will give any AR9 fits.....depending on magazine or lower, this is a little bump on the road. And does not speak to the 100's, if not 1000's of barrels we've produced in the last 4 years. IF he can't get it.....of course we will have him send the barrel back for inspection.....even we don't get it right every time and THAT is where our customer service comes in. I will say.....this is a rarity....the only other time we've had an issue was when a guy was trying to feed HST hollowpoints. Tim So yesterday I competed with it in a 6 stage SC match using round nose 124, 115 factory ammo and it ran flawlessly. Not a single issue with it, well other than I’m not fast. Not a single FTF, FTE. My main concern was it being my first build I had missed something or I went to cheap on the lower. I did way to much reading in what parts I wanted to use and I chose Taccom upper due to the huge amount of great reviews, people I know using them so I do feel it’s a one off issue. But an issue I can easily overcome. No Tim I’m not sending it back to you it ran flawlessly yesterday. Link to comment
TRUBL Posted April 18, 2022 Share Posted April 18, 2022 18 hours ago, RCKable said: So yesterday I competed with it in a 6 stage SC match using round nose 124, 115 factory ammo and it ran flawlessly. Not a single issue with it, well other than I’m not fast. Not a single FTF, FTE. My main concern was it being my first build I had missed something or I went to cheap on the lower. I did way to much reading in what parts I wanted to use and I chose Taccom upper due to the huge amount of great reviews, people I know using them so I do feel it’s a one off issue. But an issue I can easily overcome. No Tim I’m not sending it back to you it ran flawlessly yesterday. great to know!!!.....our offer still stands if you ever have issues. Tim Link to comment
dmshozer1 Posted April 18, 2022 Share Posted April 18, 2022 On 4/16/2022 at 10:52 PM, TRUBL said: They ARE!!!......we can't control everything ya know. But our barrels will give you the absolute best chance of feeding just about any bullet profile out there. We all know that flat nose and hollowpoints will give any AR9 fits.....depending on magazine or lower, this is a little bump on the road. And does not speak to the 100's, if not 1000's of barrels we've produced in the last 4 years. IF he can't get it.....of course we will have him send the barrel back for inspection.....even we don't get it right every time and THAT is where our customer service comes in. I will say.....this is a rarity....the only other time we've had an issue was when a guy was trying to feed HST hollowpoints. Tim What part of another vendors bolt has to be modified to use your super feed barrel? Link to comment
dmshozer1 Posted April 18, 2022 Share Posted April 18, 2022 1 hour ago, dmshozer1 said: What part of another vendors bolt has to be modified to use your super feed barrel? Never mind Tim, Got the answer from your website. Link to comment
mikeAZ Posted April 29, 2022 Share Posted April 29, 2022 I have 2 TacCom barreled PPC's they are 5 1/2" x 16" & 10 " x 16" w/ shrouds. I shoot in steel competition weekly.I'm using "Blue Bullets" x 124 grn. RN. x 3.4 TG.. The 5 1/2" barrel is an early one feed ramper and has 100's x100's of rounds thru it. I believe his barrels are as good as your going to find and a good value, PLUS he will talk to you and is very helpful..... I use the ETS mags almost 100%. (Glock guys usually run a little shorter OAL... I like to stay near 1.12/1.13, too long and you will have nose-down issues). Link to comment
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now