postalpainmaker Posted December 7, 2016 Share Posted December 7, 2016 Hey guys. I stainless steel tumble tons of brass. I currently am working on 6000lbs of 5.56 brass I acquired. I need a efficient way to dry the brass. I've been using 6 food dehydrators with so-so results. Is there a better way? Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
MeatPuppet Posted December 7, 2016 Share Posted December 7, 2016 Used pizza oven from a closed pizza joint. It has an adjustable temp control and conveyor belt feed. Wet goes in... dry comes out. Link to comment Share on other sites More sharing options...
postalpainmaker Posted December 7, 2016 Author Share Posted December 7, 2016 Used pizza oven from a closed pizza joint. It has an adjustable temp control and conveyor belt feed. Wet goes in... dry comes out.That's brilliant!Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
safeactionjackson Posted December 7, 2016 Share Posted December 7, 2016 Another option would be a commercial food warmer, more or less a larger version of the food dehydrator. Might be able to pick one up used.Sent from my iPad using Tapatalk Link to comment Share on other sites More sharing options...
postalpainmaker Posted December 7, 2016 Author Share Posted December 7, 2016 Another option would be a commercial food warmer, more or less a larger version of the food dehydrator. Might be able to pick one up used.Sent from my iPad using TapatalkAnother good option. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
3gunDQ Posted December 7, 2016 Share Posted December 7, 2016 I hit it with an electric leaf blower really good then put a fan on it..... should be good to go in 12-15 hours Link to comment Share on other sites More sharing options...
lefty o Posted December 9, 2016 Share Posted December 9, 2016 when i made brass for a living, we washed, and dried brass in a large baird drum (big cement mixer). for drying it essentially had a big vent with forced hot air. turn the heat on and let it spin till dry. if the #6000 of brass is a one time thing, id just work my w ay thru it slowly instead of making an investment in big machinery. Link to comment Share on other sites More sharing options...
anachronism Posted December 12, 2016 Share Posted December 12, 2016 Are you decapping the brass before tumbling? I'm working through 55 gal. of 5.56 processing myself, and have found that it's a lot easier to remove the water if the primers out. I generally spin the brass after draining it, kind of like a washing machine does on the spin cycle, to get most of the water out, then I tumble the brass in walnut to absorb the remaining water and dry the brass. I'm not having issues with media clumping when I do it this way. I've been kind of curious about adapting a 110V apartment size clothes dryer for drying brass too. My mind works in strange ways at times. Screwing a thin rubber mat to the inside of the drum should protect the case mouths. Link to comment Share on other sites More sharing options...
postalpainmaker Posted December 12, 2016 Author Share Posted December 12, 2016 I am ultra sonic cleaning with out decapping then dry in dehydrators. Then size , decap, swage and trim the stainless steel tumble and then dry. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
NatureBoy Posted December 12, 2016 Share Posted December 12, 2016 how about a used clothes dryer with brass put into a heavy duty laundry bag Link to comment Share on other sites More sharing options...
Paul Winters Posted December 16, 2016 Share Posted December 16, 2016 Oven at about 220 degrees. Been doing it for years. Drain the excess water and leave in for about 30 minutes then air cool and you are done. Excess water might need more time. I use muffin trays for rifle brass with the base up. I find the temperature doesn't affect brass and extra time souldn't hurt. Paul : -)# Link to comment Share on other sites More sharing options...
postalpainmaker Posted December 17, 2016 Author Share Posted December 17, 2016 I'm looking at 1000watt dehydrators Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
Rob5r Posted February 12, 2017 Share Posted February 12, 2017 I built a dryer. It only takes 5-10 minutes to dry about half my load of brass. My home made wet tumbler does @ 2500 9mm cases at a time. I roll the wet brass on a dry towel, then in to my dryer. I used a 5 gal bucket. Punched a @ 6" x 6" hole in the side, near the bottom and put a small forced air heater, like the one's people put under their desk at work. Then I bolted wire mesh inside the bucket, right above the heater. I stir the brass every couple of minutes, using a plastic windshield scraper I had laying around. That knocks any loose water around and heats all the brass evenly. And if you have any stray SS pins/chips, they fall to the bottom of the bucket. By the time I get me tumbler reloaded and running, the brass is dry. As everyone else says, decapping first will make them dry sooner. I use a universal decapping die for that. You might be able to figure out a better heat source, but the small forced air heater has worked well for me. Sometimes I put a lid on it, but you have to be careful not to over heat the heater. Mine has a safety device so it doesn't overheat. Trip that and your heater will be down for a while. I think the key here is forced, heated air and stirring the brass. Also the stirring helps to prevent the heater from overheating. Link to comment Share on other sites More sharing options...
postalpainmaker Posted February 13, 2017 Author Share Posted February 13, 2017 Ya I think I might have to custom build a force air drier. I would like to have something that keeps them moving as well. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
postalpainmaker Posted February 13, 2017 Author Share Posted February 13, 2017 I looked into drying with heated corn cob. Big money unit but looked good. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
ffgats Posted February 23, 2017 Share Posted February 23, 2017 try search Frankford arsenal, saw a couple months ago about a "Dryer" Link to comment Share on other sites More sharing options...
anachronism Posted February 26, 2017 Share Posted February 26, 2017 Perhaps you can find a small apartment sized 110v clothes dryer at a good price. Link to comment Share on other sites More sharing options...
JFoley001 Posted March 8, 2017 Share Posted March 8, 2017 Another vote for a used kitchen oven. 220-230F for 30-60 min and you are done. Primer in, out, doesn't matter. Link to comment Share on other sites More sharing options...
polizei1 Posted March 11, 2017 Share Posted March 11, 2017 (edited) For a "small" investment, I would look into using a Harbor Freight cement mixer and a forced air heater (usually propane but you can find electric as well). I use a HF mixer to clean the brass and then just lay them out in the sun for a few hours, but the forced air would keep them moving and would dry them faster. Plus, when they're dry, just dump them out! Just be sure to keep the heat off the mixer motor. Edited March 11, 2017 by polizei1 Link to comment Share on other sites More sharing options...
rustybayonet Posted April 12, 2017 Share Posted April 12, 2017 Link to comment Share on other sites More sharing options...
postalpainmaker Posted May 13, 2017 Author Share Posted May 13, 2017 Bought 3 of these 1000 watt dehydrators. Work good but at least 4hrs as they only go to 175deg. I need a higher temp option for a lot of brass processing. Sent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
Kaldor Posted May 19, 2017 Share Posted May 19, 2017 On 2/12/2017 at 11:15 AM, Rob5r said: I built a dryer. It only takes 5-10 minutes to dry about half my load of brass. My home made wet tumbler does @ 2500 9mm cases at a time. I roll the wet brass on a dry towel, then in to my dryer. I used a 5 gal bucket. Punched a @ 6" x 6" hole in the side, near the bottom and put a small forced air heater, like the one's people put under their desk at work. Then I bolted wire mesh inside the bucket, right above the heater. I stir the brass every couple of minutes, using a plastic windshield scraper I had laying around. That knocks any loose water around and heats all the brass evenly. And if you have any stray SS pins/chips, they fall to the bottom of the bucket. By the time I get me tumbler reloaded and running, the brass is dry. As everyone else says, decapping first will make them dry sooner. I use a universal decapping die for that. You might be able to figure out a better heat source, but the small forced air heater has worked well for me. Sometimes I put a lid on it, but you have to be careful not to over heat the heater. Mine has a safety device so it doesn't overheat. Trip that and your heater will be down for a while. I think the key here is forced, heated air and stirring the brass. Also the stirring helps to prevent the heater from overheating. Thats brilliant. Ive been kicking around building something like that. Any pics you can share? Link to comment Share on other sites More sharing options...
frankge Posted May 25, 2017 Share Posted May 25, 2017 I use a laundry bag and set it on top of my AC unit. The bag is pretty thick but dries really quick in my Florida heat... Link to comment Share on other sites More sharing options...
GregJ Posted May 25, 2017 Share Posted May 25, 2017 On 12/11/2016 at 10:00 PM, postalpainmaker said: I am ultra sonic cleaning with out decapping then dry in dehydrators. Then size , decap, swage and trim the stainless steel tumble and then dry. Sent from my iPhone using Tapatalk I wet tumbled mine without decapping, then dried as you are. Had a helluva time with primers being pulled back. Turned out the primer was gluing itself in. Another reason to decap before wet tumbling. I decided to switch back to media tumbling, problem solved. Link to comment Share on other sites More sharing options...
nbot Posted May 25, 2017 Share Posted May 25, 2017 If you're doing some serious volume... Check these guys out. http://sgcbrass.com/product-category/media/ Video https://www.youtube.com/watch?v=auo98kDegLA&t=62s They make a patented Stainless Media Separator / Dryer. I have a smaller unit and it works fast. Brief breakdown.. (Separates stainless, rinses, and drys) All steps make using stainless media so much faster and better. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now