MP9 Posted July 3, 2016 Share Posted July 3, 2016 Hi all. I have been reloading 147rn xtreme bullets for a year now. 1.140 for my cz mostly and 0 issue.. All pass the chamber check.. It will drop free on the barrel itself.. I have a dillon 650 and dillon dies. I decided to try blue bullets 147RN, dillong case lube.. And i get a lot more noticable bulk or coke bottle than isual and almost all bullets wont drop free/ clean on the barrel. Actual sometimes it drop free on the chamber checker (lyman and egw) I try more crimp, nothing changed. Even worst i beleive, seated it deeper and nothing..1.130-.135.. No sure how to fix it. Can i get it to work without ordering u-die and FCD? Before xtreme and i was using bayou and with hard brass i had a lot of fail chamber check.. When i switched to xtreme it was awesome as i never had failed chamber.. As ordering 3000 blue bullets seams cheap Im giving a try.. Any advice? Thanks Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted July 3, 2016 Share Posted July 3, 2016 It's possible that the Blue Bullets have to be seated even deeper for your CZ ... I'd shorten them up and try The Plunk Test, until you find an OAL that works in your gun. You might have to go lower than 1.130" ... Good luck with it Link to comment Share on other sites More sharing options...
Southpaw Posted July 3, 2016 Share Posted July 3, 2016 The bullet profile is very different between the Xtreme and Blue Bullets, you probably need to load shorter as Jack said. Try this test in post #4 to determine the max OAL for the Blue Bullets in your barrel: http://www.czfirearms.us/index.php?topic=34225.0 Link to comment Share on other sites More sharing options...
Wheeljack Posted July 3, 2016 Share Posted July 3, 2016 I liked the BB 147gr in .358. I would the resize the bullet to the .358 and .357 and .356. I had different sized bullets for different guns. BUT, the shape of the BB would not let me load long enough. At BB's they know the shape of their RN does not let you load long enough in some guns. So I just bought the new SNS 147gr. .357 bullets. This will be a compromise for the 3 guns. The conical flatnose loads very long if you want. Working with the BB, I don't like using the FCD so I just loaded shorter, until it did pass the plunk test. I think the maximum you can load into a shell is .300. In my pistol, I have to resize the bullet to .356 instead of the .357 I wanted and then could not load longer that l.l35. I don't know what diameter bullet you are using, but a resizing die may help you. Link to comment Share on other sites More sharing options...
Smitty79 Posted July 3, 2016 Share Posted July 3, 2016 (edited) For my Shadow, I load those to 1.12. At that length, there are about 10 head stamps that don't case gauge. Their case walls thicken nearer the case mouth. CBC and Aguila are the most common problem brass types. I segregate them and use them with other bullets. Blue Bullets are a wonderful value. They aren't keeping up with their competitors on the latest trends in bullet profiles. I'd like to see 125 and 147 flat point bullets without lube grooves Edited July 3, 2016 by Smitty79 Link to comment Share on other sites More sharing options...
Nathanb Posted July 3, 2016 Share Posted July 3, 2016 I have the same issue with Aguilar brass as smitty when using bb Link to comment Share on other sites More sharing options...
B_RAD Posted July 3, 2016 Share Posted July 3, 2016 I have the same problem with foreign brass. Eggleston makes some 147 gr coated lead with what looks like a similar profile as the extreme/Berrys profile so they should be able to loaded out to a longer OAL. I've got some ordered but haven't gotten them in so I haven't been able to load any up. Though, I'm probably gonna stick with plated. There not much more than coated and seem to be easier to load and don't smoke. Plus I'm switching to tite goup and that's $5 less than WSF and requires less powder so in the end I think I'm actuall spending less per round. Link to comment Share on other sites More sharing options...
Smitty79 Posted July 3, 2016 Share Posted July 3, 2016 Best profile I've found is the Acme NLG 147. Personally, I'm going to move to 124/5s soon. I've been measuring performance with both bullet weights. I don't see a measurable differences. Link to comment Share on other sites More sharing options...
biglou13 Posted July 4, 2016 Share Posted July 4, 2016 For my Shadow, I load those to 1.12. At that length, there are about 10 head stamps that don't case gauge. Their case walls thicken nearer the case mouth. CBC and Aguila are the most common problem brass types. I segregate them and use them with other bullets. Blue Bullets are a wonderful value. They aren't keeping up with their competitors on the latest trends in bullet profiles. I'd like to see 125 and 147 flat point bullets without lube grooves +1 what he said........ My favorite Blue bullet is the 147 flat point !!!!! .... as soon as i finish what i have now..... its the blue 147 FP for the duration...... unless they make finally make no lube groove. (why they don't make one already ????) i had similar issues culling brass did help, luckily only had a small batch of 147 RN (and yes cbc and aguilla were the culprits) blue 147 flat points, longer seating, no culling!!!! Link to comment Share on other sites More sharing options...
rdinga Posted July 4, 2016 Share Posted July 4, 2016 Have you tried the Precision Delta 147 fmj-tc? A delightful bullet to work with. Link to comment Share on other sites More sharing options...
Smitty79 Posted July 4, 2016 Share Posted July 4, 2016 Have you tried the Precision Delta 147 fmj-tc? A delightful bullet to work with. Way too expensive. My last batch of 147 Blue Bullets was 6.8 cents a round. Link to comment Share on other sites More sharing options...
CZ85Combat Posted July 4, 2016 Share Posted July 4, 2016 Commercial casting molds are expensive and each machine uses several. My guess is they will not swap then out until they are wore out. Link to comment Share on other sites More sharing options...
xdr Posted July 5, 2016 Share Posted July 5, 2016 Just loaded some blue Bullets for the first time today. I had the same problem and fixed it by backing off the crimp until it was just barely crimped. I think the more aggressive crimp was slightly flaring the case. Hi all. I have been reloading 147rn xtreme bullets for a year now. 1.140 for my cz mostly and 0 issue.. All pass the chamber check.. It will drop free on the barrel itself.. I have a dillon 650 and dillon dies. I decided to try blue bullets 147RN, dillong case lube.. And i get a lot more noticable bulk or coke bottle than isual and almost all bullets wont drop free/ clean on the barrel. Actual sometimes it drop free on the chamber checker (lyman and egw) I try more crimp, nothing changed. Even worst i beleive, seated it deeper and nothing..1.130-.135.. No sure how to fix it. Can i get it to work without ordering u-die and FCD? Before xtreme and i was using bayou and with hard brass i had a lot of fail chamber check.. When i switched to xtreme it was awesome as i never had failed chamber.. As ordering 3000 blue bullets seams cheap Im giving a try.. Any advice? Thanks Link to comment Share on other sites More sharing options...
MemphisMechanic Posted July 5, 2016 Share Posted July 5, 2016 (edited) With coated bullets: 1) shorten your load with your previous crimp and what-not until they pass the plunk test. (You drop it into your disassembled gun's barrel and it spins freely). 2) Pull that bullet. Does it have a groove or ridge in it where it was being undersized / pinched by the sizing die? Back your crimp off until you're juuuust taking the bell out of the case mouth. You should barely be able to see where the mouth of the case was wrapped around the bullet when you pull one. You certainly shouldn't be able to feel a ridge there. I find these two steps result in amazingly reliable, accurate ammo with coated bullets. I also found running a Lee FCD to be totally worthless. If you leave it where the round gets properly final-sized with lead or coated bullets, it is probably under sizing your round at the same time. That can cause all manner of issues. By the time it is backed off enough to pass the above "crimp just enough to get the bell off the case mouth and get them to pass the gauge" test... the FCD isn't actually doing anything that an ordinary Dillon or RCBS crimp die doesn't do. Edited July 5, 2016 by MemphisMechanic Link to comment Share on other sites More sharing options...
biglou13 Posted July 12, 2016 Share Posted July 12, 2016 (edited) i happened to click on vendor area this guy makes 147 no lube groove flat point 147's !!!!!!!!! http://www.brianenos.com/forums/index.php?showforum=313 (tell him biglou sent you.... bump for BE vendor!!) Edited July 12, 2016 by biglou13 Link to comment Share on other sites More sharing options...
copecowboy22 Posted July 13, 2016 Share Posted July 13, 2016 i happened to click on vendor area this guy makes 147 no lube groove flat point 147's !!!!!!!!! http://www.brianenos.com/forums/index.php?showforum=313 (tell him biglou sent you.... bump for BE vendor!!) Thanks for the bump. I attached a pic of the bullets I currently make. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now