mmosur Posted March 24, 2012 Share Posted March 24, 2012 New to reloading and wonder how often you veterans clean brass. After each time it's used? If so, why? Or just if the outer casing starts getting dirty from the ground, bullet lube, etc. Any pointers here would be appreciated. Link to comment Share on other sites More sharing options...
Scootertheshooter Posted March 24, 2012 Share Posted March 24, 2012 I place it in the used bucket then after I have a bunch start cleaning. I usually wait til I have 1000 prices to clean Link to comment Share on other sites More sharing options...
GrumpyOne Posted March 24, 2012 Share Posted March 24, 2012 Clean after shooting. Link to comment Share on other sites More sharing options...
mmosur Posted March 24, 2012 Author Share Posted March 24, 2012 What am I looking for with cleaning? Is the purpose of cleaning to get the inner casing clean or the outer casing clean?. Again, I'm new to reloading so I want to be sure I'm not missing any safety steps. Most of the brass I fire once still seems very clean at least on the outside and it would seem I can run it through the press a second time at least with no issues. Is this wrong or dangerous?. I want to be sure I know all the reasons for cleaning as I'm guessing it's not just to make the brass look pretty and shiny. Link to comment Share on other sites More sharing options...
whistlepig Posted March 24, 2012 Share Posted March 24, 2012 Me, I run pistol brass through a tumbler just long enough to get it smooth and get any debris knocked off. I don't go for shine. Then it goes straight into the system....... Rifle brass prep is another story. Link to comment Share on other sites More sharing options...
GrumpyOne Posted March 24, 2012 Share Posted March 24, 2012 You are cleaning the outside of the case to remove dirt, soot, whatever accumulates on the outside after firing when it hits the ground. You don't have to clean brass at all, but it definitely makes reloading a lot easier. It also makes it easier to spot cracks and splits in the brass. As you reload it time after time, brass can split/crack. Link to comment Share on other sites More sharing options...
EkuJustice Posted March 24, 2012 Share Posted March 24, 2012 I typically go for the nice shiny brass. Last batch came out great after it set there for like 12 hrs(fell asleep before it was done) Link to comment Share on other sites More sharing options...
jdphotoguy Posted March 24, 2012 Share Posted March 24, 2012 I go for shinny, but just for aesthetic reasons, yes, I'm anal. So I clean my brass before it goes to the reloading station. Use corn cob media I get from a large pet supply store, guess they use it for animal bedding or something, add a splash of low odor mineral spirits and Nu-Finish car wax. Also throw in strips of used drier sheets to collect some of the dust tumbling creates. Link to comment Share on other sites More sharing options...
blaster113 Posted March 24, 2012 Share Posted March 24, 2012 if I'm cleaning .40 practice brass I'll either do it after the session (200-300) cases, or after about 2 sessions. .38SC brass is done right after shooting so I dont mix it up with anything else. Link to comment Share on other sites More sharing options...
Action Pistolero Posted March 24, 2012 Share Posted March 24, 2012 (edited) Brass is cleaned before reloading because the dirt on the cases will scratch the carbide insert in the die. Once scratched, it will scratch the cases. These scratches could cause the case walls to thin and prematurely split. The only thing to worry about on the inside of the case is gravel or other debris that can brake off the decapping pin. Edited March 24, 2012 by Action Pistolero Link to comment Share on other sites More sharing options...
BullyDog Posted March 24, 2012 Share Posted March 24, 2012 Me, I just throw everything in the stainless tumbler for 2-3 hours and it comes out like new. Link to comment Share on other sites More sharing options...
old506 Posted March 24, 2012 Share Posted March 24, 2012 You don't have to clean brass. You could wipe them off and run'em. Many years ago I didn't have a tumbler when I started, I certainly didn't run the volume that we are shooting now though. Once fired Brass picked up off a concrete floor? No problem. Link to comment Share on other sites More sharing options...
Trini Posted March 24, 2012 Share Posted March 24, 2012 I have containers for different caliber brass. When I get a large amount then I run it for a couple of hours. I found a large box of 40 brass (3K) from several area matches that I worked in 2010 and did it four batches. Link to comment Share on other sites More sharing options...
Hi-Power Jack Posted March 24, 2012 Share Posted March 24, 2012 Most of the brass I fire seems very clean Mosur, what caliber/load are you shooting? When I shot only .41 revolver, the brass never hit the ground, I reloaded on a single stage press, and I used to wipe the brass individually with the lube - cleaned and lubed at the same time. Now that I shoot 9mm outside, I run it all thru a case cleaner and clean everything mechanically. Link to comment Share on other sites More sharing options...
mmosur Posted March 24, 2012 Author Share Posted March 24, 2012 I'm shooting mostly 40, 45, 38 special right now. Appreciate all the comments. Like Action Pistolero mentioned, I wasn't sure if dirt or such could affect the die and then in turn weaken or damage future brass. I guess a little time cleaning is worth it. Link to comment Share on other sites More sharing options...
mbopp Posted March 27, 2012 Share Posted March 27, 2012 My brass gets tumbled every time I shoot it. Getting the dirt off saves the dies. For grungy range pickup stuff the procedure is more involved. I deprime 45 cases with a 44 Mag expander die with a decapper pin (the die is big enough so the brass isn't resized.) Then I boil them in a water / salt / vinegar solution to get the crud out. Rinse, dry, inspect, the they go into the "to be tumbled" bucket along with my regular brass. Link to comment Share on other sites More sharing options...
Paul-the new guy Posted March 27, 2012 Share Posted March 27, 2012 Brass is cleaned before reloading because the dirt on the cases will scratch the carbide insert in the die. Once scratched, it will scratch the cases. These scratches could cause the case walls to thin and prematurely split. The only thing to worry about on the inside of the case is gravel or other debris that can brake off the decapping pin. carbide dies would be very hard to scratch. I tumble before loading so they will be pretty Link to comment Share on other sites More sharing options...
nathandewalt Posted March 27, 2012 Share Posted March 27, 2012 Tumbled everything I shoot for about two hours. Link to comment Share on other sites More sharing options...
cardguy Posted March 28, 2012 Share Posted March 28, 2012 I tumble after I shoot, it's easier to find the brass after it's been fired if it is shiny. Link to comment Share on other sites More sharing options...
M1Garand Posted March 28, 2012 Share Posted March 28, 2012 I clean it every time I fire it. I clean it the night before I'm going to reload it. I put it in my tumbler, which is upstairs and hooked to a timer, and let it clean for a couple hours and its ready in the morn. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now