-
Posts
141 -
Joined
-
Last visited
Content Type
Forums
Profiles
Events
Store
Everything posted by BullyDog
-
New 1050 not seating new primers
BullyDog replied to B_RAD's topic in Dillon Precision Reloading Equipment
I will check them both, thanks. -
New 1050 not seating new primers
BullyDog replied to B_RAD's topic in Dillon Precision Reloading Equipment
Let me know what you find out. I just started having this problem also. I replaced the blue plastic tip and cleaned everything and it was still popping primers on the bench. This is so frustrating when it does happen and the H335 powder just gets everywhere. -
Thanks Sarge, exactly what I thought when I seen them.
-
Bought a few years ago from someone either on this forum or a different one. But when I noticed it says 38 acp and not 380 acp What the hell? Do I need to get 380 acp dies now to load 380 acp?
-
Primer system 650 vs 1050 ?
BullyDog replied to Hammer1's topic in Dillon Precision Reloading Equipment
If only the 650 priming system would not use the ski jump and allow the primer to stay in priming wheel for another chance to prime. So many times, you need to pull a case and you loose another primer. -
Any pics? Shot mine on my second outing.
-
Are people having good luck with RF100's lately?
BullyDog replied to bofe954's topic in Dillon Precision Reloading Equipment
I have two, one setup for small and one setup for large primers. the only problem I have with them once in while is where the little plastic piece that sets right where the tube meets the machine where the primers drop into the filler tube. That plastic piece will sometimes get jammed up causing the primers to not drop and get backed up. -
30-06 in Dillon Super 1050 ?
BullyDog replied to Hammer1's topic in Dillon Precision Reloading Equipment
I have loaded 300 wm on my super 1050, I just put the seater die in the last station. -
Which dies should I try to find for loading precision .308?
BullyDog replied to JC49ae's topic in Rifle/Shotgun
1) Dillon universal de-capping Then 2) Dillon trim die and trimmer Then 3) lee collet die to set neck tension Works great for me. -
More questions about the Dillon RT1200
BullyDog replied to SWThomas's topic in Dillon Precision Reloading Equipment
I currently use a Dillon 1050 to trim and size with. Station 1 I used a Dillon universal decapping die Station 2 swage Station 6 trim with Dillon rt1200 trimmer Next remove lube in tumbler Next when I go to reload the bullets, setup a lee collet die in station one and adjust mandrel and neck tension. This also removes or cleans out the flash hole that might have stuck media in it. Here is YouTube video of some guy showing a lee collet die -
More questions about the Dillon RT1200
BullyDog replied to SWThomas's topic in Dillon Precision Reloading Equipment
I use a universal decapping die, then the RT1200 trimmer on the first step. The second step is to use a lee collet die to set neck tension and clean out flash hole. -
Do I really need a balance beam scale?
BullyDog replied to JLeeCZ's topic in Dillon Precision Reloading Equipment
I have and rcbs chargemaster and a couple of beam scales. I am thinking of getting a second digital scale from Dillon to double check my loads. It's been a while since I used my beam scales, but they are here for when there is no power or something fails. -
I bought the paint from weldingsupply.com for cheap and my setup is right on.
-
Super 1050 primer Kaboom causes?
BullyDog replied to rowdyb's topic in Dillon Precision Reloading Equipment
Wow never heard of this happening before. The only thing I can think of is your primer tube was not tight. I am talking the threaded nut on top was loose. -
They say the neck should reach 650 degrees when it's at the right temp.
-
I do not have the paint. I will pick up some this weekend. I have read a lot, and watched several videos.
-
I just got done testing a few .223 cases. What do you think? Do they look right? I never let them get cherry red. Sent from my iPad using Tapatalk HD
-
Anybody find or know where to get the following H335 H4865 RL 15 Varget A2230
-
Go figure, I have a RL 1050 and a S 1050. RL 1050 is running small primer setup and the S 1050 is running large primer setup. Today I decided to load .223 on the S 1050, only to forget I do not have a extra small primer setup. I normally load my .223 on the RL press, but the only thing is with the shorter stroke I can not use my redding competition seater die. Not worth it breaking down two presses just to change the primer setup. So I went to order a small primer setup for my S 1050 today, and my question is: why do they charge so much for this setup?
-
Anyone running a 1050 with a lee collet neck sizing die? How do you have it set up for trim and reload? I just bought some for my rifle cases, and I am trying to figure out the best method to use them on this press. Before or after I trim the cases?
-
.308 Redding Comp Seater problem on 1050
BullyDog replied to roxfo's topic in Dillon Precision Reloading Equipment
I have this same problem with redding competition seater on RL1050 What is the work around? -
1050 Powder Inspection Station
BullyDog replied to mcracco's topic in Dillon Precision Reloading Equipment
Here is my setup. Found this 9mm color camera at Home Depot on clearance for $59.00 Works great with a zip tie to the case feeder stand. Currently I have it setup to inspect 45 acp, when I use it on the rifle cases I just insert it in the powder check die. I used a set of rubber o-rings to hold it in place. Sent from my iPad using Tapatalk HD -
Personally I would double what you shoot for any given year. You never know what might come down the road.
-
Doesn't say something on the side of the die? What it is? Never seen that either.