Prov1x

The loads I have for my glock 35 worked great in the tanfo. 4.5g of titegroup with a 180g xtreme HP with an OAL of 1.135".... I chrono'd the load through the tanfo and was getting 170PF with it. Same experience here. The Henning magwell is pretty soft and the limited amount I dryfired with it has caused quite a few dings! Sent from my LG-D850 using Tapatalk Yeah I started with the load data I saw on here that people were using for their M&P's and glocks. But with the same amount at 4.6gr of vvn320, I am getting no where close to pf. And my plans changed, sick kid at home now so I won't get back to the range today. Is there any coating or finish to put on the Henning Magwell to make the inside of it harder?

What type of load data did you get yours to make pf? I am still working on getting a load adjusted accordingly and have only put about 75 rounds through mine since I got it completed. I am using 180gr MG CMJ bullets loaded to 1.145oal (yes they run reliably in the short amount of rounds I have tried) with VVN320. In my custom 2011 and my 1911 I am running the same bullet but at 1.185oal with 5.2gr of VVN320 at 170pf. Since I have to shorten the oal of the round I started with 4.6gr and 4.7gr but not close to pf yet. They are hitting right around 888-900fps. I loaded up some 4.9gr and some 5.1gr loads to test out today to see if I can get to 170pf, which is where I like to be. But the gun shoots well and is very accurate, no malfunctions or anything like that so far. The one thing I'm not sure of is the Henning magwell seems to be a bit soft. Just in practicing dry fire and reloads the magwell has some dings in it and the back part of the magwell has a little groove dug into it where the retaining pin has rubbed it while doing mag changes. I'm going to take my 2011 out and compare the two today. I'm not sure I can justify having a 4k$ gun sitting in the safe when I can have 2 limited guns for 2800$ and have the exact backup gun to my main one....decisions decisions...and I am mainly a production and single stack shooter too but that McLearn gun is really really nice!

I am loading to 1.13 with 124gr rn xtreme bullets. No problems.

Did you shorten the rounds as described above?

14.58039 is what I'm calculating for the HHF. Let me know what you end up with when the April run happens. It should be about 92.4331% SINGLESTACK Classifiers Date Number Club F Percent Entered 3/22/15 06-03 ATA PRACTICAL SHOOTERS Y 92.4331

My grips I got from stoeger came with torx.

Signup here http://matchsignup.org/match/default.php?matchid=379 It's going to be a great match!

Good catch, did you order the wrong lengths?

My trigger was delivered today. Ordered March 30th and delivered April 8, 9 days. Seems very reasonable coming from overseas.

I think Ben would probably still be the favorite seeing how he hasn't been beaten by a U.S. shooter at Nationals in 3-4 years...or definitely Eric if he decides to come back and shoot again.

I ordered mine on march 31st and by april 2nd it was in the u.s. That is all it says now too. I haven't got it yet but I know I will, it just takes time.

For Can You Count CM 06-03 in Single Stack I know the classifiercalc doesn't do it correctly or cmcalc. The last two times I have shot it I scored 100 points in 8.10 seconds and a 12.3457 hit factor...cm or cc had it at 75%ish and it actually came out to a 84.6733% This month 100 points in 7.42 seconds and a 13.4771 hit factor...cm or cc had it at 80%ish and it actually came out to a ? (since the updates hasn't been ran for April yet) but I am guessing based off of the last % difference that it should be in the low 90% range.?

I tried a pair on my cz and they crack pretty easily if you really try to snug them down.

That means it's probably in customs. You will get it.

Nobody has single action triggers available over here, semi curved short finger, at the moment. And they just came out with a steel version, again not available here at the moment, so I went ahead and placed an order.

https://www.dropbox.com/s/gsjk5wgpnfi7kpo/IMG_0457.MOV?dl=0 Is that the titan hammer?

I have ordered from him in the past and just placed an order on Monday as well. Usually it takes about 10 to 12 days to show up at your house.

This ^ Pin should stop pretty quickly.

Clipping the plunger a link is all Ive ever done. Never heard they made a plunger spring. What benefit does this give? Lightens the trigger pull because the trigger bar isn't having to exert as much force to depress the plunger. But I have found if you go too light, with the pen spring, it makes the reset mushy.

3.8gr of N320 with 125mghp is what I was loading for my stock 2 at 131pf.

When is someone going to post a how to video or demo pics? ;-)

Do you use any snap caps, brass or anything else in dry fire?

I have not had to fit the firing pin block on either of my stock 2 or 3. Both have the henning pin. I think the fitting issue comes when you switch sears and hammers.

All you need is 4 classifiers on record to get a classification. Sorry, I misread your initial post as you already had a few classifiers, not just one. Minor in limited, depending on your skill level, if you are shooting fast enough and get all A's then it won't matter. :-) I would just shoot for accuracy if you are new to the sport because if you drop one C in minor, you are already giving up 2 points.

Classifiers, not qualifiers, and 4 of your highest, out of your first 6, will get you classified. Shooting minor in production, single stack or limited?