ErikW Posted October 13, 2005 Share Posted October 13, 2005 I shot a bunch of rounds through my 17 yesterday, cleaned it today, greased it with Slide Glide #3, and re-assembled it. The trigger wouldn't go forward. I re-assembled it with the trigger forward, and when dry-fired, it doesn't return. What did I do wrong, or what's broke? Link to comment Share on other sites More sharing options...
BritinUSA Posted October 13, 2005 Share Posted October 13, 2005 Simplest cause could be some dirt/debris inside it somewhere, if you have some compressed air I would squirt that into it to see if it dislodges the problem. Otherwise, no idea.... Link to comment Share on other sites More sharing options...
eric nielsen Posted October 13, 2005 Share Posted October 13, 2005 Take the top end off, look at the back where the trigger hold-back spring is. Pull forward on the actual [plastic] trigger - a little - and see if the whole trigger bar pops back under spring tension. If it doesn't, the hold-back spring is broke. Link to comment Share on other sites More sharing options...
Nik Habicht Posted October 13, 2005 Share Posted October 13, 2005 Erik, if that doesn't solve it, take some pictures of the gun..... Link to comment Share on other sites More sharing options...
AikiDale Posted October 14, 2005 Share Posted October 14, 2005 cleaned it today, greased it What did I do wrong? <{POST_SNAPBACK}> You cleaned and greased it. Glocks never need cleaning. Everytime you clean one it pukes. (in my limited experience) Link to comment Share on other sites More sharing options...
carinab Posted October 14, 2005 Share Posted October 14, 2005 Did you lose a spring cup or perhaps not get them on quite right? How much of a tear down did you do? 31 parts...shouldn't take long to check them all. BTW, you almost made your topic title an actual sentence in german - Mein Glock ist kaput. Link to comment Share on other sites More sharing options...
Rob Boudrie Posted October 14, 2005 Share Posted October 14, 2005 If it's a conventional Glock trigger (3, 5 or 8lb), my guess is that it is the coil trigger return spring. This is a $.50 part is most likley broken or not connected to both the trigger bar and ejector housing. Did you do a detail strip the lower when you took it apart for cleaning? Link to comment Share on other sites More sharing options...
ErikW Posted October 14, 2005 Author Share Posted October 14, 2005 Pidgin Deutsch is more fun, ja? All I did was take off the top end. I've never gone any farther other than when I installed a 3.5 connector. The one spring visible in the back is working. Link to comment Share on other sites More sharing options...
Flexmoney Posted October 14, 2005 Share Posted October 14, 2005 Tear it down. Clean and inspect. While you are at it, do the $0.25 trigger job. http://www.alpharubicon.com/mrpoyz/glock/ I clean with simple green, hot water and a tooth brush. Run some Q-tips in the striker tunnel to get that gunk out (regularly). Hair dryer to dry it all up. Lube all the proper areas (as per manual). Link to comment Share on other sites More sharing options...
Sean Gaines Posted October 14, 2005 Share Posted October 14, 2005 It is your trigger spring in the main housing near the connector.had the same problem during a match, and the gun would still shoot, but when slide came back the striker wouldn't catch on the cruciform consistantly. But if I held the gun a certain way the striker would catch. without the spring(thats glock for you, eat dirt and shoot rocks). DNF the stage. Went to the truck put in a new one and finished the match. Oh and by the way it was a wolf extra power trigger spring that broke, went back to factory one and have had no problems since. Link to comment Share on other sites More sharing options...
ErikW Posted October 14, 2005 Author Share Posted October 14, 2005 OK I am really hosed now. I took it apart and cleaned in there, with the same result. I even compared how it all looked to my carry gun, fine. Then I put it back together sans connector. Dumb. Well now I can't pull the trigger to get the slide off. Link to comment Share on other sites More sharing options...
Sean Gaines Posted October 14, 2005 Share Posted October 14, 2005 uh oh, what did ya do Erik?if you cant pull the trigger the slide wont come off, unless you come in from the back plate of the slide and push down on the cruciform to engage the strker(iits like pulling the trigger) but you may have to destroy your back plate to get to the cruciform Link to comment Share on other sites More sharing options...
iainmcphersn Posted October 14, 2005 Share Posted October 14, 2005 (edited) You should be able to lock the slide back and remove the back plate more or less normally. Pull the striker/firing pin and then remove the slide. Edited October 14, 2005 by iainmcphersn Link to comment Share on other sites More sharing options...
Sean Gaines Posted October 14, 2005 Share Posted October 14, 2005 You should be able to lock the slide back and remove the back plate more or less normally. Pull the striker/firing pin and then remove the slide. <{POST_SNAPBACK}> Your absolutely right I was thinking of a stuck slide. Yeah you can rack the slide back and then proceede to take off the back plate and then take out the striker and internals, once you have done that than you can relase the slide stop and take the slide off. Link to comment Share on other sites More sharing options...
ErikW Posted October 14, 2005 Author Share Posted October 14, 2005 I got the slide off by locking it open, then removing the striker. Re-assembling it, it works. There must have been a piece of something, but I didn't see any grit or bristle of my cleaning brush. The spring is fine. Link to comment Share on other sites More sharing options...
mcoliver Posted October 14, 2005 Share Posted October 14, 2005 Now that it's already working, don't ever clean it by yourself again...ever. Link to comment Share on other sites More sharing options...
Clay1 Posted October 14, 2005 Share Posted October 14, 2005 I think that it is the other way around. Get use to cleaning that thing once in a while and tearing it down and then you will be more use to it. Here is a good site with many great pictures on detail stripping a Glock: http://www.topglock.com/info/info.htm I had a similar problem when I did the 25 trigger job and bent my connector while removing it. Embarrassing but this is the thread: http://www.brianenos.com/forums/index.php?...topic=25551&hl= Make sure when you take the connector in and out you don't pry on it but push it out from the off side through the little square hole. Lessons learned. Rick Link to comment Share on other sites More sharing options...
the duck of death Posted October 17, 2005 Share Posted October 17, 2005 Many rounds thru my G23 and other than the slide it's never taken apart, here's what I do: THE FRAME Spray with Simple Green and scrub with a toothbrush. THE SLIDE Take it apart and spray with Simple Green then scrub with a toothbrush. Clean the Striker hole with a Q tip. Look down the striker hole to make sure none of the Q tip remains. It is important to take the slide apart so it can be properly dried. THE BARREL Spray with Simple Green & run a paper towel patch down the barrel soaked in Simple Green. Then a couple of patches with Hoppe's #9. THE RINSE Use moderately hot water and rinse in the sink. THE DRYING Use a hair dryer to dry the parts DO NOT get the plastic too hot. Push a dry paper towel patch down the barrel until dry. THE OILING Follow the outline in the manual. I use synthetic motor oil for lub. Link to comment Share on other sites More sharing options...
vincent Posted October 17, 2005 Share Posted October 17, 2005 Wow you guys clean the inside of the barrel on a Glock? I've never had anything that didn't just come out with a few passes of the freebie plastic brush. I don't use any solvent on the gun anywhere and haven't ever had a need. For a basically stock Glock I use a pretty simple procedure: Field strip. Wipe off the excess crud every 1000 rounds with dry cloth. Brush out barrel with plastic brush, scrape chamber with dry cloth over brass punch if needed. Add a bit of lube in the prescribed spots. Re-assemble. Every 5000 rounds, detail strip the entire gun since it is so easy. Wipe off all parts with dry cloth and inspect. Clean firing pin channel with dry Q-tip. Re-assemble and then add a bit of lube in the prescribed spots. Clean magazines with mag brush and dry cloth. Clean the mags whenever you drop them in sand or other fine dirt. Whenever recoil spring fails the "press check" test replace it and to be safe replace the firing pin spring and trigger return spring at the same time. Replace magazine springs every year or so. Glocks don't like too much attention and really don't like lube in the firing pin channel. Lots of oil is not your friend with a Glock. Link to comment Share on other sites More sharing options...
atmar Posted October 18, 2005 Share Posted October 18, 2005 Lots of oil is not your friend with a Glock. <{POST_SNAPBACK}> that's why i use automotive grease Link to comment Share on other sites More sharing options...
Harmon Posted October 18, 2005 Share Posted October 18, 2005 (edited) i shot glocks untill i got the SVI and you cant put too much oil in them... i found the gun tracked better when the recoil spring assembly was soaked in 50 wt oil. little oil on barrel but the trigger parts and slide rails got hosed with oil... i cant remember any malfunctions caused by oil. Other than it doesn need much oil to operate, why else would you not oil one? Edited October 18, 2005 by harmongreer Link to comment Share on other sites More sharing options...
vincent Posted October 18, 2005 Share Posted October 18, 2005 why else would you not oil one Getting a lot of lube in the firing pin channel can slow the firing pin down and cause misfires. Link to comment Share on other sites More sharing options...
jessej Posted October 18, 2005 Share Posted October 18, 2005 i never thought Erik could break a glock "put down the glock and step away from the bench!" Link to comment Share on other sites More sharing options...
racerba Posted October 20, 2005 Share Posted October 20, 2005 ...why else would you not oil one? <{POST_SNAPBACK}> Oil attracks dirt which will keep it in the gun which can cause malfunctions. Gumming up the firing pin channel, as Vince said, is one problem. Gumming up the connector is another. If you regularly clean out your Glock after every 100 rounds, then by all means, soak it with all the oil you want. Lightly oiling the Glock, you can go through thousands of rounds without thorough cleaning. Glocks do not need much oil - so why over oil it? Nothing in life is bad for you unless you overdo it. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now