Furrly Posted January 28, 2021 Share Posted January 28, 2021 I load 10.6 gr for 115 JHP ..very small amount of spillage nothing major.. Nothing is available right now.. Link to comment Share on other sites More sharing options...
zombywoof Posted January 28, 2021 Share Posted January 28, 2021 The latest batch I just received is a little on the slow side. I did one test run with my DVC-O 8.7 grains with 125 blue 1250 fps. Link to comment Share on other sites More sharing options...
himurax13 Posted January 28, 2021 Share Posted January 28, 2021 3 hours ago, zombywoof said: The latest batch I just received is a little on the slow side. I did one test run with my DVC-O 8.7 grains with 125 blue 1250 fps. 9.8 gets me 1380 with powder coated 125. I go .2 more with Hollow Points. Link to comment Share on other sites More sharing options...
Posvar Posted January 28, 2021 Share Posted January 28, 2021 With my Limcat KKM barrel guns with three popple holes I was at 10.0g at 1.165 and it was 172PF (this was 124g JHP PD) Link to comment Share on other sites More sharing options...
Posvar Posted January 28, 2021 Share Posted January 28, 2021 17 hours ago, regor said: For those who switched to MP from HS6, what was your change in charge weight? I've seen plenty of people comment that it burns clean (HS6 makes my Czechmate filthy), but is there any substantial change in feel? What is powder fill like in a 9mm case? I'm running 8.5gr of HS6, which leaves me a reasonable amount of room in the case so I don't have any spillage issues from the case plate indexing and I don't think the load is compressed based on my measurements. Also how is availability vs HS6? Seems like MP is cheaper but charge weights are higher so cost savings is negligible. Had to go up to 10g on my guns for SW MP. Still lots of room in the case. I tried HS6 and it was FILTHY and the impact hit me weird in my hand. Tried all different loads from 168-173PF and it was just odd. SW MP felt really nice with a nice predictable impulse in your hand. Dot tracked much less side to side versus HS6. Also, the gun got very very hot quickly with HS6 and I needed two guns to practice with. Powder in a 9mm case was not even close to full. Plenty of room compared to 3N38, etc. Around here in Southeast MP is pretty easy to get. Link to comment Share on other sites More sharing options...
d3ydx3 Posted March 21, 2022 Share Posted March 21, 2022 On 2/1/2020 at 11:46 AM, hurley326 said: Is anyone else running this powder on a Mark 7 Evolution/Revolution? I think because it’s such a fine grain powder it’s causing inconsistent powder drops for me. I’m getting some at 10.1 grains and others at 8 grains. Curious if you ever got SWMP measure reliably in the Mark 7 mechanical powder measure? I've used AA7 previously in it and had zero issues, but bought some SWMP a few months ago. My charges vary +/- 0.5-1gr. Seems that it will run the same charge for several cycles, but eventually throws out something off. Had a case this morning where it was repeatedly dropping 10.1gr consistently, and then I come back a few hours later only to find it is dropping a 4ish gr charge now. My lot is 115 which was very clumpy out of the jug. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now