MemphisMechanic Posted June 27, 2018 Share Posted June 27, 2018 The Q5 Match. It’s better than sex. Darn right. Link to comment Share on other sites More sharing options...
PokerNGuns Posted June 28, 2018 Share Posted June 28, 2018 Is there another option for a rear sight on the Q5 yet? Or is that called a red dot haha Link to comment Share on other sites More sharing options...
jayjay1 Posted July 16, 2018 Share Posted July 16, 2018 Didn´t find a comment about red dot options yet, might be I´ve overseen it, if so I´m sorry. Can you talk me about red dot options? I think Kim Hwansik runs a Delta Point? I´m looking for a red dot for my getting older eyes. It should have a wide glass area, being lightweight, low-mounted, parallax-free. Thought about the Shield RMS, but don´t have experience with it. And for IPSC: How big should the Dot be, accounting to my aging eyes? I´m thankful for every opinion. Link to comment Share on other sites More sharing options...
MemphisMechanic Posted July 16, 2018 Share Posted July 16, 2018 (edited) @jayjay1 ... On the first question the leading cantidate these days is the DeltaPoint Pro. I run one in 2.5MOA and love the thing. That said, after two matches in carry optics I have a standard PPQ’s slide on the way to a machinist to mill the optic down into it. I strongly dislike how high dots ride on top of the Q5’s adapter plates, so it’ll be my Production gun from now on. Ironic. The Shield optic is anything but equipped with a large window; that sucker is TINY. Other options to look at would be the Cmore RTS 2, and the Viper & Venom from Vortex. Edited July 16, 2018 by MemphisMechanic Link to comment Share on other sites More sharing options...
dansedgli Posted July 17, 2018 Share Posted July 17, 2018 I saw a comparision and the glass size wasn't much different. The overall size was much smaller though. I've got 2 DPP's but was thinking about one to go on a shadow 2 for PDO. They look much better. Link to comment Share on other sites More sharing options...
jayjay1 Posted July 17, 2018 Share Posted July 17, 2018 8 hours ago, MemphisMechanic said: @jayjay1 ... On the first question the leading cantidate these days is the DeltaPoint Pro. I run one in 2.5MOA and love the thing. That said, after two matches in carry optics I have a standard PPQ’s slide on the way to a machinist to mill the optic down into it. I strongly dislike how high dots ride on top of the Q5’s adapter plates, so it’ll be my Production gun from now on. Ironic. The Shield optic is anything but equipped with a large window; that sucker is TINY. Other options to look at would be the Cmore RTS 2, and the Viper & Venom from Vortex. Hi MemphisMechanic, thank you for taking the time. I´m shooting IPSC on the old continent, if I would mill the slide I would be upgraded by the RO: "Welcome to Open!" That´s what makes the Shield RMS sexy, it has its own very thin adapter plate which is much lighter and lower as the original plates of the Q5. So the DPP would ride HIGH on mine, no milling allowed. It cost´s about 500 bucks here. The C-More RTS 2 is at about the same price, I didn´t have it on my list till now, thanks for that. Vortex Venom and Viper are running about 280 bucks over here, if you can get one, which is not that easy. Are all of them compatible with the adapter plates of the Q5? I will do some further research about these Dots, thanks again. Link to comment Share on other sites More sharing options...
Matt1 Posted July 17, 2018 Share Posted July 17, 2018 Shannon Smith was talking CO & red dots on the latest Firearms Nation podcastSent from my iPhone using Tapatalk Link to comment Share on other sites More sharing options...
MemphisMechanic Posted July 17, 2018 Share Posted July 17, 2018 If you are only going to shoot one gun, the high ride of the DPP on a Q5 isn’t a problem. On top of an adapter plate, *every* red dot sits high enough that you need to re-learn your index: on the draw you have to drop the gun in front of your eye 2 cm in order to find the dot. It’s not a big deal, but I want my gun milled since it is legal here, and lets me switch back to my iron-sighted guns more smoothly. Link to comment Share on other sites More sharing options...
jayjay1 Posted July 18, 2018 Share Posted July 18, 2018 Matt1, thanks I listened it. MemphisMechanic: Well, I´m about to shoot only one pistol with red dot now. But I do shoot some pistol with irons on it also. Will this be a problem, switching forth and back from irons to red dot? Link to comment Share on other sites More sharing options...
MemphisMechanic Posted July 19, 2018 Share Posted July 19, 2018 I don't know; I shot the Q5 with a high-mounted dot to try it out, and then went back to Production. I just know I really like shooting guns with dots recessed into the slide a lot more... but I don't have enough experience to answer that. Link to comment Share on other sites More sharing options...
Almo Posted July 27, 2018 Share Posted July 27, 2018 MemphisMechanic, In an earlier post you say you've been running 13# since day one. But, in a later post, you say you've settled on 15#. See page 15 of this thread. Did you change or is that a typo? Link to comment Share on other sites More sharing options...
MemphisMechanic Posted July 27, 2018 Share Posted July 27, 2018 Typo. I’m still using a 13 pound spring! Link to comment Share on other sites More sharing options...
jaep1911 Posted August 18, 2018 Share Posted August 18, 2018 Just installed a Sprinco trigger spring kit. I do not have a fancy pull gauge but the pull seems to have gone down by a pound. The trigger return is still positive. I like it. Link to comment Share on other sites More sharing options...
je85 Posted August 18, 2018 Share Posted August 18, 2018 2 hours ago, jaep1911 said: Just installed a Sprinco trigger spring kit. I do not have a fancy pull gauge but the pull seems to have gone down by a pound. The trigger return is still positive. I like it. Nice!! Must be new? I went with the home depot spring pack and misc spring for the firing pin safety plunger. Of course a little polishing helps.. Has a nice reset like a 2lb cz trigger. Link to comment Share on other sites More sharing options...
jaep1911 Posted August 18, 2018 Share Posted August 18, 2018 19 hours ago, je85 said: Nice!! Must be new? I went with the home depot spring pack and misc spring for the firing pin safety plunger. Of course a little polishing helps.. Has a nice reset like a 2lb cz trigger. It is not new. has been around for some time. I shot with it today and liked it. Link to comment Share on other sites More sharing options...
Jeff O Posted August 27, 2018 Share Posted August 27, 2018 On 4/4/2018 at 5:31 PM, MemphisMechanic said: I’ve been running a 13lb Wilson 1911 spring in my Q5 since the day I set it up for matches and never had an issue with it. 13 feels light as far as “stay in battery” force, when you first install and test it by hand. For sure. But it feels no weaker than an M&P or Glock with the same spring. And all three run fine with it in my experience, when fed good ammo. Memphis, what guide rod are you running/ Couldn't find the info looking back....... Link to comment Share on other sites More sharing options...
MemphisMechanic Posted August 27, 2018 Share Posted August 27, 2018 Link to comment Share on other sites More sharing options...
MemphisMechanic Posted August 27, 2018 Share Posted August 27, 2018 Custom turned it. Link to comment Share on other sites More sharing options...
je85 Posted August 27, 2018 Share Posted August 27, 2018 I went with a Jager Gen 4 Uncaptured Hardened Steel Guide Rod Heavy Extended G34/G35 http://jagerproducts.com/index.php?main_page=product_info&cPath=35&products_id=114&zenid=eavbe3ocv9d0j8tke0lq8fa194 The dimensions are perfect. The washer that comes with it wont work. I used a stainless washer. 13lb spring works but if worried go with 14lb. Link to comment Share on other sites More sharing options...
je85 Posted September 6, 2018 Share Posted September 6, 2018 Has anyone mounted a Jpoint or a Shield red dot on the Q5? Do any of the mounting plates work? I know Shield makes a lower adapter plate but its very expensive and hard to get. Link to comment Share on other sites More sharing options...
MemphisMechanic Posted September 6, 2018 Share Posted September 6, 2018 (edited) On 8/27/2018 at 6:00 PM, je85 said: I went with a Jager Gen 4 Uncaptured Hardened Steel Guide Rod Heavy Extended G34/G35 http://jagerproducts.com/index.php?main_page=product_info&cPath=35&products_id=114&zenid=eavbe3ocv9d0j8tke0lq8fa194 The dimensions are perfect. The washer that comes with it wont work. I used a stainless washer. 13lb spring works but if worried go with 14lb. What 13lb spring were you running with this? Aftermarket flat wire springs like the IMSI won’t fit a rod that fat. Edited September 6, 2018 by MemphisMechanic Link to comment Share on other sites More sharing options...
je85 Posted September 6, 2018 Share Posted September 6, 2018 1 hour ago, MemphisMechanic said: What 13lb spring were you running with this? Aftermarket flat wire springs like the IMSI won’t fit a rod that fat. Wolf glock spring trimmed down. Link to comment Share on other sites More sharing options...
MemphisMechanic Posted September 6, 2018 Share Posted September 6, 2018 (edited) 23 minutes ago, je85 said: Wolf glock spring trimmed down. Okay that makes sense. I think a full-length round wire spring would go into coil-bind before the slide was fully to the rear on a Walther. Edited September 6, 2018 by MemphisMechanic Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now