Hammer1 Posted July 15, 2014 Share Posted July 15, 2014 . Forget the production rate comparisons for a moment. How much more joy do you get when reloading with a Dillon 1050 than when reloading the same cartridge with a Dillon 650 ? . Link to comment Share on other sites More sharing options...
Boxerglocker Posted July 17, 2014 Share Posted July 17, 2014 Given that both machines are set up right and serviced properly. The 1050 by far is more enjoyable for me. Especially .223, eliminating the primer pocket swaging required off the machine if using a 650. The priming on the down stroke is what I really like. Link to comment Share on other sites More sharing options...
Torogi Posted July 17, 2014 Share Posted July 17, 2014 (edited) I'd be honest and say, i dont enjoy reloading at all. It is a chore. I chose Dillon because it works, 650 and 1050. Mr. Bulletfeeder, RF100. To make everything faster. That being said, like previous post says, 1050 is easier to work with provided that everything is set to work all the time. Upward priming has its advantages on the 650, but the swaging helps a lot with smoothness of a 100 count cycle without stopping for crimped pockets. Downstroke priming is nice too but personally its not worth the price difference if its the only reason to upgrade (like me). The travel is shorter between the toolhead and shellplate which is nice. Ill be on the lookout for an RL, i heard its even shorter. My opinion is largely based on loading pistol ammo. Edited July 17, 2014 by Torogi Link to comment Share on other sites More sharing options...
jmorris Posted July 17, 2014 Share Posted July 17, 2014 Depends, I would rather load rounds that don't need to be swaged with this 650 rather than a stock 1050. An automated 1050 is joyless when it is loading though, I am generally not in the room while it is loading. Link to comment Share on other sites More sharing options...
Tom Freeman Posted July 17, 2014 Share Posted July 17, 2014 If I win the lottery I will never again load a single round of ammo. Till then I am perfectly content to load on my high volume ammo on my 1050 and precision rifle ammo on my 550. Link to comment Share on other sites More sharing options...
DWFAN Posted July 17, 2014 Share Posted July 17, 2014 I get much more joy from loading on the 1050 vs my Hornady LnL. But I agree with Reece and Tom. Loading is a chore. Link to comment Share on other sites More sharing options...
safeactionjackson Posted July 18, 2014 Share Posted July 18, 2014 Personally I believe the s1050 provides a easier/simpler experience once setup, of course I'm not speaking to caliber conversions. s1050 is currently setup for 9mm only and it has run pretty much flawlessly. ~g Link to comment Share on other sites More sharing options...
Mikelindsey Posted August 14, 2014 Share Posted August 14, 2014 I've had an XL 650 for about 8 months and loaded about 100 rounds in each of .40, .45, & 223. I thought I'd really get into this buying every upgrade available even the non Dillon niceties like the new primer dump bottle I have several thousand cases, bullets, primers and powders, electronic calipers and scales and large tumbler and I could go on. Prob 3k worth of gear. I wish I would have just put the money into finished new rounds. Really considering selling every thing. Just buying the ammo and having more trigger time. It's not a money saving thing for me I'd rather not spend the time reloading. Think I could get $2k for all? Link to comment Share on other sites More sharing options...
datguy Posted August 15, 2014 Share Posted August 15, 2014 I have a S1050 with bulletfeeder. I can load 100 rounds in 6 minutes without rushing. I quite enjoy the whole process, especially in the 1050. Link to comment Share on other sites More sharing options...
warpspeed Posted August 15, 2014 Share Posted August 15, 2014 I love using the 1050 to load. Hands down. The single pull forward with no push to prime is sweet. Link to comment Share on other sites More sharing options...
jaredr Posted August 15, 2014 Share Posted August 15, 2014 if cost is no issue, the 1050 beats the 650 hands down. Link to comment Share on other sites More sharing options...
ScottyPotty Posted August 15, 2014 Share Posted August 15, 2014 I want a 1050 but I load 12 different calibers and both my 650 work so well. But I'm always tempted Link to comment Share on other sites More sharing options...
rjacobs Posted August 15, 2014 Share Posted August 15, 2014 The joys of loading on the 1050 beat every other Dillon hands down. The joys of buying caliber conversions are not present. No joy can be had when spending 300-400 bucks on a caliber conversion and tool head. But if you dont need to load 12 calibers, a 1050 is awesome. I have mine setup for 9mm, 223, and 300BLK with 3 tool heads, and 2 shell plates. I have a small rifle case feeder and a small pistol case feeder that I share between my 2 1050's since they are so easy to yank out and swap. Link to comment Share on other sites More sharing options...
ZombieHunter Posted August 16, 2014 Share Posted August 16, 2014 I've had an XL 650 for about 8 months and loaded about 100 rounds in each of .40, .45, & 223. I thought I'd really get into this buying every upgrade available even the non Dillon niceties like the new primer dump bottle I have several thousand cases, bullets, primers and powders, electronic calipers and scales and large tumbler and I could go on. Prob 3k worth of gear. I wish I would have just put the money into finished new rounds. Really considering selling every thing. Just buying the ammo and having more trigger time. It's not a money saving thing for me I'd rather not spend the time reloading. Think I could get $2k for all? Why would you buy that setup if you've only loaded 300 rounds in 8 months? You'd have been better off buying a single stage or a cheaper 550. I'm guessing you have no interest in tuning your own loads to a desired power factor and to your specific gun(s)? That is a major advantage vs. factory ammo. Link to comment Share on other sites More sharing options...
lvipscshooter Posted September 2, 2014 Share Posted September 2, 2014 I have both presses, and like some above, do not enjoy reloading. That said, when both machines are adjusted and tuned perfectly, I would pick the 1050 every time. Priming on the downstroke and in my opinion, more consistency with OAL and crimp on my 38SC loads. I have run @ 25k rounds through my1050 so far this year. Link to comment Share on other sites More sharing options...
DEP44 Posted September 3, 2014 Share Posted September 3, 2014 . Forget the production rate comparisons for a moment. How much more joy do you get when reloading with a Dillon 1050 than when reloading the same cartridge with a Dillon 650 ? . I'd say 37% more joy. Having 3 positions on the crank is a big one for me. Processing military 308 takes a long stroke and loading only a short stroke as it's a way lighter process. Add the primer seating on the upstroke and the pocket swager and there's no going back. Link to comment Share on other sites More sharing options...
COF Posted September 3, 2014 Share Posted September 3, 2014 Depends, I would rather load rounds that don't need to be swaged with this 650 rather than a stock 1050. An automated 1050 is joyless when it is loading though, I am generally not in the room while it is loading. What kind of bullet feeder are you using? Link to comment Share on other sites More sharing options...
jmorris Posted September 3, 2014 Share Posted September 3, 2014 It's a GSI feeder but I built the collator and mount myself. Link to comment Share on other sites More sharing options...
dvc4you Posted September 4, 2014 Share Posted September 4, 2014 (edited) I went from a 550 to an RL1050 with Mr. Bulletfeeder, I load 38SC, 9x19 and 40, Reloading is a PIA, so the faster I do it the better, as someone mentioned, 100 rounds in six minutes is easy. The big advantage is the additional stations (for example for 38SC: station 1 38SC Dillon die, station 2 EGW undersize die) and doing all operations in the down stroke. Edited September 4, 2014 by dvc4you Link to comment Share on other sites More sharing options...
GDIS46 Posted September 4, 2014 Share Posted September 4, 2014 (edited) I'm not even qualified to comment on this since I have never used nor owned a 650 but here is my two cents worth anyway. I went from a Lyman Spartan single stage press to two Super 1050s. One is set up for small primers and the other for large primers. So if you ask how much more joy is the Super 1050...... In my experience, the difference between those two is similar to "Walking to Town" versus "Driving a McLaren P1 to Town" !!! Edited September 4, 2014 by GDIS46 Link to comment Share on other sites More sharing options...
jmorris Posted September 4, 2014 Share Posted September 4, 2014 Reloading is a PIA, so the faster I do it the better I can load manually faster than my automated machine. Kind of a turtle vs hair thing though, it only takes a break when it needs to be filled or there is a problem. Link to comment Share on other sites More sharing options...
jmorris Posted September 4, 2014 Share Posted September 4, 2014 (edited) It takes twice as long to load 100 vs manually but is much less work. Edited September 4, 2014 by jmorris Link to comment Share on other sites More sharing options...
GDIS46 Posted September 7, 2014 Share Posted September 7, 2014 (edited) Reloading is a PIA, so the faster I do it the better I can load manually faster than my automated machine. Kind of a turtle vs hair thing though, it only takes a break when it needs to be filled or there is a problem. John, I love your computer control system for your 1050! Do you have the details/instructions on how I could build one for myself or do you sell them??? Edited September 7, 2014 by GDIS46 Link to comment Share on other sites More sharing options...
RangerTrace Posted September 7, 2014 Share Posted September 7, 2014 For me, speaking specially about pistol rounds, I prefer the 650, by a large margin over the 1050. Keeping in mind, my 650 was set up by lee Neel for 40 and the 1050's I've used are high use machines at Infinity. My 650 is a sexy bitch compared to those worn out whores!! Link to comment Share on other sites More sharing options...
jmorris Posted September 7, 2014 Share Posted September 7, 2014 John, I love your computer control system for your 1050! Do you have the details/instructions on how I could build one for myself or do you sell them??? This is the thread I posted when I first put it together. No real details or "prints", it was more of a thrown together project. The most time consuming part was learning how to program the PLC and display. I originally was going to just use a latching relay and time delay relay then have any fault unlatch it (using LED's to indicate which one), to stop the machine. I wound up using the PLC really to learn more about them and it also gives more feed back. I have other projects ahead of making the system for sale but will post it in the appropriate place if I make them in the future. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now