Julien Boit Posted April 23, 2013 Share Posted April 23, 2013 Hi all, I have a technical question that may sound weird but here it goes : Is it possible to change a factory carbine length gas system to a rifle length gas system ? I have this in my mind for quite some time and I want to have opinions, here is how I would do : - Plug the current gas port in the barrel with a steel ball , and modify the current gas block to have a screw on top of the steel ball to secure it. - Drill a new gas port at the right location (rifle length). - Put a new gas block at the new location (maybe an adjustable one). - Make a new gas tube that would pass by the old gas block and go back into the upper receiver (Taking a rilfe length tube should do the trick with some bending). What you guys think about that ? This is purely theoric (for the moment ?) but do you think it is doable ? I know putting a new barrel with the right gas system woule be easier, but hey, I have spare time ;-) Link to comment Share on other sites More sharing options...
grouse Posted April 23, 2013 Share Posted April 23, 2013 Not worth it. Sell the barrel and buy a new one Link to comment Share on other sites More sharing options...
mpom Posted April 24, 2013 Share Posted April 24, 2013 unless you have a machine shop and the skill to do this, your money would be better spent in buying a new rifle gas barrel and gas block, in my opinion. mark Link to comment Share on other sites More sharing options...
caspian guy Posted April 24, 2013 Share Posted April 24, 2013 I gotta ask why? having said that if I had to do it, I think I'd tap the existing gas port for a short grub screw. Then I'd install it with permanent locktite. following that I'd probably turn a small collar on my lathe to slide over the barrel to cover the plug and lock it down ( maybe use a set screw on the bottom of the collar to secure it). You could probably use a small low profile gas block as a collar if you wanted. I think adco does something like this and maybe puts a tack weld on the plug to keep it from backing out? You could email them and ask... My other question would be is the diameter where you were planning on putting the new gas port large enough for a standard gasblock? (I suppose if it wasn't you could turn it down to the next smallest size, or make a custom gas block)? Link to comment Share on other sites More sharing options...
Julien Boit Posted April 24, 2013 Author Share Posted April 24, 2013 unless you have a machine shop and the skill to do this That's my day job . Link to comment Share on other sites More sharing options...
Bearcave Posted April 24, 2013 Share Posted April 24, 2013 Brownells has a pigtail gas tube, rifle length tube for carbine length gas port. Don't know about the export part if you are in France. You have the machine shop handy may be able to make one of them. Link to comment Share on other sites More sharing options...
broke_again Posted April 25, 2013 Share Posted April 25, 2013 Is the barrel the correct diameter at the point you want to put the new gas block location? Link to comment Share on other sites More sharing options...
Julien Boit Posted April 25, 2013 Author Share Posted April 25, 2013 (edited) Is the barrel the correct diameter at the point you want to put the new gas block location? Barrel is .750 at this location. Edited April 26, 2013 by Julien Boit Link to comment Share on other sites More sharing options...
Chuck Anderson Posted April 25, 2013 Share Posted April 25, 2013 How long is the barrel? Most I've seen with carbine gas are 16" or shorter. That's not long enough for a rifle gas system. The port would have to be larger than usual because of the short dwell time past the port. You'd end up with all, and more, of the issues of a carbine system just at greater expense. The shortest rifle gas barrels I've seen are 17" and most are 18"+. Link to comment Share on other sites More sharing options...
Julien Boit Posted April 26, 2013 Author Share Posted April 26, 2013 The barrel is a 14.5 inches M4 profile. I aslo thought about putting a pigtail gas tube and/or an adjustable gas block. Link to comment Share on other sites More sharing options...
caspian guy Posted April 26, 2013 Share Posted April 26, 2013 At 14.5" I think you'd have a hard time making anything longer than midlength work. (even that would likely be under gased). Link to comment Share on other sites More sharing options...
Chuck Anderson Posted April 26, 2013 Share Posted April 26, 2013 You can do a pigtail but definitely not a rifle length gas system. You'd only have about 2.5 inches of barrel after the port. Even the 7.5 inch barrels which are a pain to tune right have 3.5. Even swapping to a mid length would not give you any benefit. Link to comment Share on other sites More sharing options...
Julien Boit Posted April 26, 2013 Author Share Posted April 26, 2013 All these thoughts lead me to one question : What's the most important, the gas tube length, or the position of the port in the barrel ? I mean, if the port is still located at the same spot (carbine length) but the gas tube is longer, is there any effect ? Link to comment Share on other sites More sharing options...
Steve RA Posted April 26, 2013 Share Posted April 26, 2013 I doubt it. Link to comment Share on other sites More sharing options...
Alaskapopo Posted April 27, 2013 Share Posted April 27, 2013 All these thoughts lead me to one question : What's the most important, the gas tube length, or the position of the port in the barrel ? I mean, if the port is still located at the same spot (carbine length) but the gas tube is longer, is there any effect ? It increases the dwell time and can help with the gun being over gassed or so the theory goes. I have never used one. Pat Link to comment Share on other sites More sharing options...
Croomrider Posted May 2, 2013 Share Posted May 2, 2013 I have done something similar to what you are trying to do and it worked fine. To plug the old gas port, just drill & tap 10-32 or something similar, but do not break through into the barrel which would open the hole in the barrel. Run an appropriate set screw in with red locktite and grind flush if desired. You can then locate the gas port where ever you want. I even made my own gas tube out of some thick walled SS tubing. I then experimented with the size of the port hole into the barrel to get the action to function smoothly without being violent. This is not rocket science and there are plenty of combinations that will work just fine. As a machinist, just go with your gut and don't let the part swappers tell you it won't work! Mike Link to comment Share on other sites More sharing options...
DaveTimm Posted May 4, 2013 Share Posted May 4, 2013 If I missed it I apologize as I'm on my phone but what is your goal? Do something different, softer felt recoil, cycling etc. One has to not only look at pressure of the has but also the dwell time. While not many would argue the pressure is high with carbine length, the dwell time is near perfect. It's a very reliable system. You certainly can proceed with the process but with that short of a dwell time you'd have to make that gas port huge. A big company use to make 16" disapators, 16 barrel with rifle length gas system and they had tons of issues. With a 14.5 itd be even worse. If your looking to soften felt recoil look at buffer and springs, comps etc. you might also really like the JP silent spring system. Link to comment Share on other sites More sharing options...
gixxerjunky Posted May 4, 2013 Share Posted May 4, 2013 Just sell your barrel and get a 14.5 middy. That's what I run with a H2 buffer without issue so far. I am running a DD barrel if that matters. Link to comment Share on other sites More sharing options...
Sako92S Posted May 7, 2013 Share Posted May 7, 2013 1. Sell the barrel and get new one or 2. Change the gas system to mid length. Use low profile gas block upside down on your old carbine gas place and then drill new hole for mid length gas. I changed my system opposed way. The Remington barrel was 22" and it was cut down to 14,5" and new middy gas system was installed. This is how it shoots now on 150m with 51gr Lapua CE bullet. Link to comment Share on other sites More sharing options...
PatUSAF Posted May 12, 2013 Share Posted May 12, 2013 You can do a pigtail but definitely not a rifle length gas system. You'd only have about 2.5 inches of barrel after the port. Even the 7.5 inch barrels which are a pain to tune right have 3.5. Even swapping to a mid length would not give you any benefit. Does the pigtail soften the recoil when installed on a carbine length system? Brownells makes it seem like its for solving FTF problems Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now