AirBorne Posted February 11, 2013 Share Posted February 11, 2013 I'm positive this has been covered but searched and couldn't find it. My question: Is there a good cleaning solvent for use in removing lead from the barrel? I used Hoppe's Elite and spent quite a while getting the barrel clean. Does anyone anyone have any experience with this matter. I'd prefer not to use a bore brush to clean said barrel since I've heard it can damage it. Yes I did break down and use the brush so that I could get it cleaned today. Any ideas are welcome and solutions to this problem is good for at least a six pack of Bud or Heineken. Thanks Link to comment Share on other sites More sharing options...
herky Posted February 11, 2013 Share Posted February 11, 2013 When I shot lead, I had good luck with a system called "Foul Out II", made by Outers. Somewhat involved, as it is an electrochemical system. I'm sure a web search will turn up some info. Link to comment Share on other sites More sharing options...
skip62 Posted February 11, 2013 Share Posted February 11, 2013 I don't like brushes either. I use Birchwood-Casey Lead Remover & Polishing cloth and cut it into patches. RB-17 works good too. Easiest thing for me is shoot a few jacketed bullets at the end of the shooting session. Not usually possible after a match though. Link to comment Share on other sites More sharing options...
AirBorne Posted February 11, 2013 Author Share Posted February 11, 2013 (edited) skip62 I've heard that both ways, one way was you can clean alot of it out by shooting jacketed bullets the other is if you shoot jacketed bullets after shooting lead you really pack the lead into the rifling. I don't have a clue which is correct so am hesitant to shoot jacketed rounds afterwards. Edited February 11, 2013 by AirBorne Link to comment Share on other sites More sharing options...
OldSchool45 Posted February 11, 2013 Share Posted February 11, 2013 I'm not quite sure how a bronze brush could hurt a steel barrel. Lead typically requires a mechanical scrubbing action to remove, unless you're using the old (hazardous) liquid mercury method, or the aforementioned electrolysis method. That said, the Lewis Lead Remover does a good job. It uses a brass or bronze screen that is pressed into the barrel grooves by an expandable rubber mandrel and pulled through the barrel. But all-in-all, a bronze brush with a good bore solvent will do a decent job of removing lead from all but the most fouled of barrels. Sent from my Verizon phone using Tapatalk Link to comment Share on other sites More sharing options...
anachronism Posted February 11, 2013 Share Posted February 11, 2013 Copper "Chore Boy" pot scrubbers wrapped around an old bronze brush will take the lead out quickly. It just takes a few strands wound, so the Chore Boy will last a long time. The scrubber and the brush are both considerably softer than jacketed bullet jackets, so you'd really have to apply yourself to damage a barrel. The only thing I know that'll dissolve lead is mercury. Link to comment Share on other sites More sharing options...
Reinz Posted February 11, 2013 Share Posted February 11, 2013 When I shot lead, I had good luck with a system called "Foul Out II", made by Outers. Somewhat involved, as it is an electrochemical system. I'm sure a web search will turn up some info. Or Foul Out III, whichever you can get your hands on, best money spent! No scrubbing by the way! Link to comment Share on other sites More sharing options...
Cd662 Posted February 11, 2013 Share Posted February 11, 2013 I've heard these arguments a lot. I don't understand how brushing with a metal that is softer than steel can damage said steel. I'm not being sarcastic, if someone can point this out to me, I'd like to know. Link to comment Share on other sites More sharing options...
goldfish Posted February 11, 2013 Share Posted February 11, 2013 I shoot jacketed rounds at end of practice and sometimes mixed them in every few rounds in the mags. Link to comment Share on other sites More sharing options...
grapemeister Posted February 11, 2013 Share Posted February 11, 2013 I rarely put anything down the barrel other than a dry bore brush when shooting lead. Once in a blue moon I'll use a little Breakfree. Even after a 200 or 300 round practice session, the bore brush is usually all I need. Link to comment Share on other sites More sharing options...
Reinz Posted February 13, 2013 Share Posted February 13, 2013 I've heard these arguments a lot. I don't understand how brushing with a metal that is softer than steel can damage said steel. I'm not being sarcastic, if someone can point this out to me, I'd like to know. I agree! I almost posted the same statement, but I am really sold on the Outer's Foul Out system. I don't like to scrub. Link to comment Share on other sites More sharing options...
anachronism Posted February 14, 2013 Share Posted February 14, 2013 I have have a Foul Out II. It does work well, but the Chore Boy trick is much faster. Link to comment Share on other sites More sharing options...
rback Posted February 14, 2013 Share Posted February 14, 2013 I use the bejeezus out of a bronze brush and MPro7 every 2-300 rounds. Barrel still looks like new inside. I haven't foud anything that will remove lead without scrubbing. Link to comment Share on other sites More sharing options...
Reinz Posted February 14, 2013 Share Posted February 14, 2013 I have have a Foul Out II. It does work well, but the Chore Boy trick is much faster. You are right, you generally have to let the Foul Out set overnight to do it's job. Or if you are in a position where you can keep an eye on it during the day; sometitmes it takes 4-6 hours. But, you can not be in a hurry with the Foul Out, that's for sure. Link to comment Share on other sites More sharing options...
Jaxshooter Posted February 15, 2013 Share Posted February 15, 2013 (edited) If you are worried about using a brush on the barrel go buy a copper pot scrubber. Cut it in pieces and run it in the bore. You can use Kroil or Break Free with the copper scruber and the lead will come out very eaisly. ( This is the way Wilson Combat recommends cleaning the barrels on their guns) I switched to Black Bullets INtl instead of lead and eliminated the problem with leading. The cost of BBI bullets is not much more than lead. It is alot better than cleaning a leaded barrel. Edited February 15, 2013 by Jaxshooter Link to comment Share on other sites More sharing options...
PinoyShooter06 Posted October 10, 2013 Share Posted October 10, 2013 I don't like brushes either. I use Birchwood-Casey Lead Remover & Polishing cloth and cut it into patches. RB-17 works good too. Easiest thing for me is shoot a few jacketed bullets at the end of the shooting session. Not usually possible after a match though. plus 1. Link to comment Share on other sites More sharing options...
ltcboy Posted October 20, 2013 Share Posted October 20, 2013 If you are worried about using a brush on the barrel go buy a copper pot scrubber. Cut it in pieces and run it in the bore. You can use Kroil or Break Free with the copper scruber and the lead will come out very eaisly. ( This is the way Wilson Combat recommends cleaning the barrels on their guns) I switched to Black Bullets INtl instead of lead and eliminated the problem with leading. The cost of BBI bullets is not much more than lead. It is alot better than cleaning a leaded barrel.I let the barrel soak in Kroil over night and then use the bronze wool wrapped around the old bore brush. I have actually chucked this knto a cordless drill and SLOWLY spun the brush in and out of the bore. Within minutes, its lead free and clean. I love Kroil.Mike Link to comment Share on other sites More sharing options...
v1911 Posted October 20, 2013 Share Posted October 20, 2013 I can shoot 200-300 rounds and only need an oiled patch to clean my barrel. If you're getting leading, there's something wrong. Link to comment Share on other sites More sharing options...
JohnnyD Posted October 22, 2013 Share Posted October 22, 2013 I can shoot 200-300 rounds and only need an oiled patch to clean my barrel. If you're getting leading, there's something wrong. Yes, most likely too small of bullets or they are being swaged down when seated/crimped. You have to really flare most cases to seat lead without swaging them down at all. Link to comment Share on other sites More sharing options...
BulletWhisperer Posted October 23, 2013 Share Posted October 23, 2013 50/50 vinegar/peroxide only with stainless barrels. For sure some will argue , and state their thrown away barrel because of the mixture . Link to comment Share on other sites More sharing options...
Babaganoosh Posted October 23, 2013 Share Posted October 23, 2013 Distilled water and sonic cleaner. Link to comment Share on other sites More sharing options...
Racer377 Posted October 23, 2013 Share Posted October 23, 2013 Kroil or some other penetrating oil, soak for 15-20 minutes. Wrap a "Chore boy" (copper scrubbing pad, found in cleaning supply aisle of local Walmart/Meijer/misc. Grocery store) around a brass bristle bore brush so that it fits nice and snug in the bore. Even the thickest leading will come right out. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now